Abstract
The effect of shallow cryogenic treatment (SCT) on the microstructure and mechanical properties of Al7075-T6 is investigated in the present work. The alloy was subjected to shallow CT at −80 °C for 72 h. Mechanical tests such as Vickers hardness test, tensile, and fatigue tests were performed on both native and treated samples. It was observed that the mechanical properties such as hardness, yield strength, and ultimate tensile strength increased by about 30, 17, and 7%, respectively, for the treated sample. The treated alloy was characterized by using the techniques such as optical microscopy, electron back scattered diffraction (EBSD), energy-dispersive x-ray spectroscopy (EDS), and transmission electron microscopy (TEM) to observe the changes in the microstructural features. EBSD results show precipitation, better distribution of second-phase particles, and higher dislocation density in the treated alloy as compared to the untreated alloy. The treatment imparts improved hardness and strength to the alloy due to precipitation hardening and high dislocation density. Fracture morphologies of the treated and the native samples were characterized by using scanning electron microscopy and it was observed that the striations were denser in the treated sample justifying the higher fatigue strength.
Similar content being viewed by others
References
J.C. Williams and E.A. Starke, Progress in Structural Materials for Aerospace Systems, Acta Mater., 2003, 51, p 5775–5799. doi:10.1016/j.actamat.2003.08.023
Y.H. Zhao, X.Z. Liao, Z. Jin, R.Z. Valiev, and Y.T. Zhu, Microstructures and Mechanical Properties of Ultrafine Grained 7075 Al Alloy Processed by ECAP and Their Evolutions During Annealing, Acta Mater., 2004, 52, p 4589–4599. doi:10.1016/j.actamat.2004.06.017
R. Smallman and A. Ngan, Physical Metallurgy and Advanced Materials, Vasa, 2011
N. Mahathaninwong, T. Plookphol, J. Wannasin, and S. Wisutmethangoon, T6 Heat Treatment of Rheocasting 7075 Al Alloy, Mater. Sci. Eng. A, 2012, 532, p 91–99. doi:10.1016/j.msea.2011.10.068
K.E. Lulay, K. Khan, and D. Chaaya, The Effect of Cryogenic Treatments on 7075 Aluminum Alloy, J. Mater. Eng. Perform., 2002, 11, p 479–480. doi:10.1361/105994902770343683
P. Baldissera and C. Delprete, Deep Cryogenic Treatment: A Bibliographic Review, Open Mech. Eng. J., 2008, 2, p 1–11. doi:10.2174/1874155X00802010001
J. Liu, G. Li, D. Chen, and Z. Chen, Effect of Cryogenic Treatment on Deformation Behavior of As-Cast az91Mg Alloy, Chin. J. Aeronaut., 2012, 25, p 931–936. doi:10.1016/S1000-9361(11)60464-0
P. Chen, T. Malone, R. Bond, and P. Torres, Effects of Cryogenic Treatment on the Residual Stress and Mechanical Properties of an Aerospace Aluminum Alloy, Proc. 4th Conf. Aerosp. Mater. Process. Environ. Technol., 2001
A. Bensely, D. Senthilkumar, D. Mohan Lal, G. Nagarajan, and A. Rajadurai, Effect of Cryogenic Treatment on Tensile Behavior of Case Carburized Steel-815M17, Mater. Charact., 2007, 58, p 485–491. doi:10.1016/j.matchar.2006.06.019
P. Baldissera, Deep Cryogenic Treatment of AISI, 302 Stainless Steel: Part I—Hardness and Tensile Properties, Mater. Des., 2010, 31, p 4725–4730. doi:10.1016/j.matdes.2010.05.013
W. Zhang, P. Bai, J. Yang, H. Xu, J. Dang, and Z. Du, Tensile Behavior of 3104 Aluminum Alloy Processed by Homogenization and Cryogenic Treatment, Trans. Nonferrous Metals Soc. China, 2014, 24(8), p 2453–2458. doi:10.1016/S1003-6326(14)63370-7
P. Das, R. Jayaganthan, T. Chowdhury, and I.V. Singh, Fatigue Behaviour and Crack Growth Rate of Cryorolled Al 7075 Alloy, Mater. Sci. Eng. A, 2011, 528, p 7124–7132. doi:10.1016/j.msea.2011.05.021
F. Bouzada, M. Cabeza, P. Merino, and S. Trillo, Effect of Deep Cryogenic Treatment on the Microstructure of an Aerospace Aluminum Alloy, Adv. Mater. Res., 2012, 445, p 965–970
C. Li, N. Cheng, Z. Chen, N. Guo, and S. Zeng, Deep-Cryogenic-Treatment-Induced Phase Transformation in the Al-Zn-Mg-Cu Alloy, Int. J. Miner. Metall. Mater., 2015, 22, p 68–77. doi:10.1007/s12613-015-1045-7
H. Panchakshari, D. Girish, and M. Krishn, Effect of Deep Cryogenic Treatment on, Microstructure, Mechanical and Fracture Properties of Aluminium-Al 203 Metal Matrix Composites, Int. J. Soft Comput. Eng., 2012, 1(340), p 340–346
J.K. Park and A.J. Ardell, Microstructures of the Commercial 7075 Al Alloy in the T651 and T7 Tempers, Metall. Trans. A, 1983, 14, p 1957–1965. doi:10.1007/BF02662363
J.K. Park and A.J. Ardell, Precipitate Microstructure of Peak-Aged 7075 Al, Scr. Metall., 1988, 22, p 1115–1119. doi:10.1016/S0036-9748(88)80114-5
J. Gjønnes and C.J. Simensen, The Precipitate, Acta Metall., 1970, 18, p 881–890
A.F. Liu, Mechanics and Mechanisms of Fracture: An Introduction, ASM International, Materials Park, 2005
S. Jia, D. Zhang, and L. Nastac, Experimental and Numerical Analysis of the 6061-Based Nanocomposites Fabricated Via Ultrasonic Processing, J. Mater. Eng. Perform., 2015, 24(6), p 2225–2233
Acknowledgment
The authors would like to thank Prof. M. Kamaraj, Mr. T. Raghaviah, Mr. R. Murugesan, Department of Metallurgical and Materials Engineering, IIT Madras, and Mr. R. Sathish, St. Joseph’s College of Engineering, for their valuable support toward this work.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Mohan, K., Suresh, J.A., Ramu, P. et al. Microstructure and Mechanical Behavior of Al 7075-T6 Subjected to Shallow Cryogenic Treatment. J. of Materi Eng and Perform 25, 2185–2194 (2016). https://doi.org/10.1007/s11665-016-2052-1
Received:
Revised:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11665-016-2052-1