Abstract
In the present study, microstructure and mechanical properties of A356 alloy including various amounts (0.2 to 1.2 wt pct) of iron were investigated. The alloys were produced by conventional gravity sand casting method. In order to determine the effect of iron addition to A356, optical and scanning electron microscopes (SEM/EDS) were used for microstructural examinations, and X-ray diffraction (XRD) analysis was carried out for phase characterization. Tensile tests were also conducted in order to determine effect of the Fe content on mechanical properties. It was found that as the Fe content of A356 was increased, the secondary dendrite arm spacing (SDAS) was decreased and the morphology of Al-Si eutectic became finer. From XRD examinations, different iron-based intermetallic compounds (β-Al5FeSi and α-Al8Fe2Si) formations were observed. It was also observed that as iron content increased, α-Al8Fe2Si intermetallic was transformed into β-Al5FeSi intermetallic. The tensile test results revealed that tensile strength and elongation values were reduced by increasing Fe content. It was also determined that β-Al5FeSi intermetallics were more negatively effective on tensile strength than α-Al8Fe2Si intermetallics.
Similar content being viewed by others
References
W.S. Miller, L. Zhuang, J. Bottema, A.J. Wittebrood, P. De Smet, A. Haszler, A. Vieregge: Mater. Sci. and Eng. A, 2000, vol. 280, pp. 37–49.
G. Eisaabadi B, P. Davami, S.K. Kim, N. Varahram, Y.O. Yoon, and G.Y. Yeom: Mater. Sci. Eng. A, 2012, vol. 558, pp. 134–43.
X. Dai, X. Yang, J. Campbell, J. Wood: Mater. Sci. and Eng. A, 2003, vol. 354, pp. 15-325.
T. Tunçay, S. Tekeli, and D. Özyürek: J. Fac. Eng. and Archit. Gaz. 2013, vol. 28, pp. 241-249.
Q.G. Wang, C.J. Davıdson, J.R. Grıffıths, and P.N. Crepeau: Metall. Mater. Trans. B, 2006, vol. 37, pp. 887-895.
D. Dispinar and J. Campbell: Mater. Sci. and Eng. A, 2011, vol.528, pp. 3860-3865.
D. Dispinar, Akhtar S., Nordmark A., Di Sabatino M., and Arnberg L: Mater. Sci. Eng. A, 2010, vol 527, pp. 3719–25.
T. Tunçay, D. Özyürek: J. Fac. Eng. and Archit. Gaz. 2014, vol. 29, pp. 271-279.
G.E. Bozchaloei, N. Varahram, P. Davami, S.K. Kim: Mater. Sci. and Eng. A, 2012, vol. 548, pp. 99-105.
G. Eisaabadi B., P. Davami, S.K. Kim, and M. Tiryakioğlu: Mater. Sci. Eng. A, 2013, vol. 579, pp. 64–70.
J. Campbell: Mater. Sci. and Technol., 2006, vol. 22, pp 127-145.
M.D. Peres, C.A. Siqueira, A. Garcia: J. Alloys Compd., 2004, vol. 381, pp. 168–181.
V. Vander, F. George. ASM Handbook, Volume 09 - Metallography and Microstructures, 1 ed., ASM International, Materials Park, OH, 2004, pp. 711–51.
Q.G.Wang, C.J. Davidson: J. Mater. Sci., 2001, vol. 36, pp. 739– 750.
L. Lu, and A.K. Dahle: Metall. Mater. Trans. A, 2005, vol. 36, pp. 819-835.
Z. Ma, A.M. Samuel, F.H. Samuel, H.W. Doty, S. Valtierra: Mater. Sci. and Eng. A, 2008, vol 490, pp. 36–51.
Z. Ma, A.M. Samuel, F.H. Samuel, H. W. Doty: A.F.S. Transactions, 2003, vol. 111, pp. 255-265.
J. Campbell: Metall. Mater. Trans. B, 2006, vol. 37, pp. 857-863.
J. A. Taylor, D. H. St John, J. Barresi, M. J. Couper: Int. J. of Cast Met. Res., 2000, vol. 12, pp. 419-430.
Q.G. Wang, C.H. Cáceres: Mater. Sci. and Eng. A, 1998, vol. 241, pp. 72–82.
Q.G Wang, C.H Cáceres and J. R. Griffiths: Mater. Sci. and Eng. A, 2003, vol. 34, pp. 2901-2912.
A.M. Samuel, H.W. Doty, S. Valtierra, F.H. Samuel: Mater. & Des., 2014, vol. 53, pp. 938–946.
N. R. Green, J. Campbell: Metall. Mater. Trans. A, 1993, vol. 173, pp. 261-266.
M. Tiryakioğlu, J. Campbell: Metall. Mater. Trans. A, 2010, vol 41, pp. 3121-3129.
A.M. Samuel, H.W. Doty, S. Valtierra, F.H. Samuel: Mater. & Des., 2014, vol. 53, pp. 938–946.
M. H. Mulazimoglu, A. Zaluska, J. E. Gruzleski, F. Paray: Metall. Mater. Trans. A, 1996, vol. 27, pp. 929-936.
L. Sanghwan, K. Bonghwan, L. Sangmok: Mater. Trans., 2011, vol. 52, pp. 1053-1062.
S.G. Shabestari: Mater. Sci. and Eng. A, 2004, vol. 383, pp. 289-298.
X. Cao, J. Campbell: Metall. Mater. Trans. A, 2004, vol. 35, pp. 1425-1435.
X. Cao, J. Campbell: Metall. Mater. Trans. A, 2003, vol. 34, pp. 1409-1420.
X. Cao, J. Campbell: Int. J. of Cast Met. Res., 2004, vol. 17, pp. 1-11.
J. Campbell: Metall. Mater. Trans. B, 2006, vol. 37, pp. 857-863.
H. Zahedi, M. Emamy, A. Razaghian, M. Mahta, J. Campbell, M. Tiryakioğlu: Metall. Mater. Trans. A, 2007, vol. 38, pp. 659-670.
T. Sivarupan, J. A. Taylor, and C.H. Cáceres: Metall. Mater. Trans. A, 2015, vol. 46, pp. 2082-2107.
T. Sivarupan, J. A. Taylor, and C.H. Cáceres: Metall. Mater. Trans. A, 2013, vol. 44, pp. 4071-4080.
Acknowledgments
The authors wish to acknowledge the financial support provided by Karabük University Scientific Research Project Department (KBU-BAP-14/1-YL-013) for this study.
Author information
Authors and Affiliations
Corresponding author
Additional information
Manuscript submitted June 9, 2016.
Rights and permissions
About this article
Cite this article
Tunçay, T., Bayoğlu, S. The Effect of Iron Content on Microstructure and Mechanical Properties of A356 Cast Alloy. Metall Mater Trans B 48, 794–804 (2017). https://doi.org/10.1007/s11663-016-0909-1
Received:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11663-016-0909-1