This article focuses on the effect of equal channel angular pressing (ECAP) on the fracture behavior of a commercially pure (CP) Ti. Standard mechanical tensile and fracture tests are performed at room temperature and 250 °C to determine the tensile mechanical properties and the J-∆a curves. The effect of temperature on the fracture properties, namely, the fracture toughness, the slope of the J-∆a curves, the total crack growth resistance, and the stability of the crack propagation before and after ECAP is investigated. Quantitative analysis of the fracture surfaces is performed using an automatic fracture surface analysis system. The energy required to form the fracture surface is estimated. The yield stress and the ultimate tensile stress are significantly increased by ECAP. However, similar to the case of other strengthening procedures, the fracture toughness decreases after ECAP.
Similar content being viewed by others
References
R.Z. Valiev, Y. Estrin, Z. Horita, T.G. Langdon, M.J. Zehetbauer, and Y.T. Zhu: J. Met., 2006, vol. 4, pp. 33–39.
F. Wetscher, A. Vorhauer, R. Stock, and R. Pippan: Mater. Sci. Eng. A, 2004, vols. 387–389, pp. 809–16.
T. Hebesberger, H.P. Stuwe, A. Vorhauer, F. Wetscher, and R. Pippan: Acta Mater., 2005, vol. 53, pp. 393–402.
A. Vorhauer, S. Kleber, and R. Pippan: Mater. Sci. Eng. A., 2005, vols. 410–411, pp. 281–84.
R.Z. Valiev, A.V. Sergueeva, and A.K. Mukherjee: Scripta Mater., 2003, vol. 49, pp. 669–74.
K.S. Kumar, H. Van Swygenhoven, and S. Suresh: Acta Mater., 2003, vol. 51, pp. 5743–74.
E. Ma: J. Met., 2006, vol. 58, pp. 49–58.
Y.H. Zhao, X.Z. Liao, S. Cheng, E. Ma, and Y.T. Zhu: Adv. Mater., 2006, vol. 18, pp. 2280–84.
Y.M. Wang and E. Ma: Mater. Sci. Eng. A, 2004, vols. 375–377, pp. 46–52.
R.Z. Valiev, R.K. Islamgaliev, and I.V. Alexandrov: Prog. Mater. Sci., 2000, vol. 45, pp. 103–89.
R.Z. Valiev and T.G. Langdon: Prog. Mater. Sci., 2006, vol. 51, pp. 881–981.
A.P. Zhilyaev and T.G. Langdon: Prog. Mater. Sci., 2008, vol. 53, pp. 893–979.
M. Faleschini, H. Kreuzer, D. Kiener, and R. Pippan: J. Nucl. Mater., 2007, vols. 367–370, pp. 800–05.
A. Hohenwarter and R. Pippan: Proceedings of the Hael Mughrabi Honorary Symposium at 2008 TMS Annual Meeting, Warrendale, PA, 2008, pp. 183–88.
G. Purcek, O. Saray, I. Karaman, and T. Kucukomeroglu: Mater. Sci. Eng. A, 2008, vol. 490, pp. 403–10.
V.V. Stolyarov, R.Z. Valiev, and Y.T. Zhu: Appl. Phys. Lett., 2006, vol. 88, p. 041905.
V.V. Stolyarov, Y.T. Zhu, I.V. Alexandrov, T.C. Lowe, and R.Z. Valiev: Mater. Sci. Eng. A, 2003, vol. 343, pp. 43–50.
“ASTM E1820-01, Standard Test Method for Measurement of Fracture Toughness,” Annual Book of Standards, ASTM, Philadelphia, PA, 2001.
J. Stampfl and O. Kolednik: Int. J. Fracture, 2000, vol. 101, pp. 321–45.
S. Scherer and O. Kolednik: Microscopy and Analysis, 2001, vol. 70, p. 15.
A. Tatschl and O. Kolednik: Mater. Sci. Eng. A, 2003, vol. 339, pp. 265–80.
I. Sabirov and O. Kolednik: Scripta Mater., 2005, vol. 53, pp. 1373–78.
O. Kolednik: Adv. Eng. Mater., 2006, vol. 8, pp. 1079–83.
I. Sabirov, D. Duschlbauer, H.E. Pettermann, and O. Kolednik: Mater. Sci. Eng. A, 2005, vol. 393, pp. 275–85.
I. Sabirov, O. Kolednik, R.Z. Valiev, and R. Pippan: Acta Mater., 2005, vol. 53, pp. 4919–30.
H.P. Stuwe: Eng. Fract. Mech., 1980, vol. 13, p. 231.
D.F. Thomason: Ductile Fracture of Materials, Pergamon Press, Oxford, United Kingdom, 1990.
Y.G. Ko, D.H. Shin, K.T. Park, and C.S. Lee: Scripta Mater., 2006, vol. 54, pp. 1785–89.
F. Dalla Torre, H. Van Swygenhoven, and M. Victoria: Acta Mater., 2002, vol. 50, pp. 3957–70.
H. Van Swygenhoven: Science, 2004, vol. 304, pp. 273–76.
S. Nemat Nasser, W.G. Guo, and J.Y. Cheng: Acta Mater., 1999, vol. 47, pp. 3705–20.
Acknowledgments
The authors acknowledge gratefully the financial support of this work by the Austrian Fonds zur Förderung der wissenschaftlichen Forschung under Project No. S10402-N16.
Author information
Authors and Affiliations
Corresponding author
Additional information
Manuscript submitted July 15, 2009.
An erratum to this article can be found at http://dx.doi.org/10.1007/s11661-010-0178-6
Rights and permissions
About this article
Cite this article
Sabirov, I., Valiev, R., Semenova, I. et al. Effect of Equal Channel Angular Pressing on the Fracture Behavior of Commercially Pure Titanium. Metall Mater Trans A 41, 727–733 (2010). https://doi.org/10.1007/s11661-009-0111-z
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11661-009-0111-z