Skip to main content
SpringerLink
Log in

A Method for Direct Measurement of Multiaxial Stress-Strain Curves in Sheet Metal

  • Published:
Metallurgical and Materials Transactions A Aims and scope Submit manuscript

Abstract

A method has been developed that allows measurement of stress-strain curves for sheet metal being deformed in multiaxial tension. The strain state is imposed using a modification of the Marciniak in-plane biaxial stretching test. Resulting stresses are measured using a modified X-ray diffraction (XRD) residual stress measurement system. This system is flexible enough to allow spatial mapping of in-plane stress and measurement of stresses at specific locations of interest on the sample, such as developing localizations. Results are presented correlating measurements on a thin strip of AA5182 with data from standard uniaxial tension test. Also presented are experimentally determined curves for this material in balanced biaxial tension in both the rolling and transverse directions.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10

Similar content being viewed by others

References

  1. Stoughton T.B. (2001) J. Eng. Mater. Technol., 123:417–22

    Article  Google Scholar 

  2. Graf A., Hosford W. (1993) Metall. Mater. Trans. A, 24A:2503–12

    CAS  Google Scholar 

  3. Chen Z., Maekawa S., Takeda T. (1999) Metall. Mater. Trans. A, 30A:3069–78

    Article  CAS  Google Scholar 

  4. Kuwabara T., Yoshida K., Narihara K., Takahashi S. (2005) Int. J. Plasticity, 21:101–17

    Article  CAS  Google Scholar 

  5. G. Gutscher, H.-C. Wu, G. Ngaile, and T. Altan: J. Mater. Processing Technol., vol. 146, pp. 1–7

  6. Raghavan K.S. (1995) Metall. Mater. Trans. A, 26A:2075–20

    Article  CAS  Google Scholar 

  7. Kuwabara T., Van Bael A., Iizuka E. (2002) Acta Mater., 50:3717–29

    Article  CAS  Google Scholar 

  8. Banabic D. (2004) Annals CIRP 53(1):219–22

    Article  Google Scholar 

  9. Marciniak Z., Kuczynski K. (1967) Int. J. Mech. Sci., 9:609–20

    Article  Google Scholar 

  10. T. Foecke, S.W. Banovic, and R.J. Fields: JOM, 2001, pp. 27–30

  11. Banovic S.W., Foecke T. (2003) Metall. Mater. Trans. A, 34(3):657–71

    Article  Google Scholar 

  12. Noyan I.C., Cohen J.B. (1987) Residual Stress: Measurement by Diffraction and Interpretation. Springer-Verlag, New York, NY

    Google Scholar 

  13. J.A. Pineault, M. Belassel, and M.E. Brauss: ASM Metals Handbook, 10th ed., vol. 8, Mechanical Testing, 2002, ASM, Materials Park, OH, pp. 484–97

  14. Perry K., Noyan I.C., Rudnik P.J., Cohen J.B. (1984) Adv. X-ray Analysis, 27:159–70

    CAS  Google Scholar 

  15. “Standard Test Method for Uniaxial Tension Test,” ASTM E8, ASTM, Philadelphia, PA, 2000

  16. Gnaeupel-Herold T., Foecke T.J., Prask H.J., Fields R.J. (2004) Mater. Sci. Eng. A, 399(1–2):26–32

    Google Scholar 

  17. Gnaeupel-Herold T., Prask H.J., Fields R.J., Foecke T., Xia Z.C., Lienert U. (2004) Mater. Sci. Eng. A, 366(1):104–13

    Article  CAS  Google Scholar 

  18. “Standard Test Method for Verifying the Alignment of X-Ray Diffraction Instrumentation for Residual Stress Measurement,” ASTM E915, ASTM, Philadelphia, PA, 2002

  19. Picu R.C., Vincze G., Ozturk F., Gracio J.J., Barlat F., Manniatty A.M. (2005) Mater. Sci. Eng. A, 390:334–43

    Article  CAS  Google Scholar 

  20. “Standard Test Method for Determining the Effective Elastic Parameter for X-Ray Diffraction Method of Residual Stress,” ASTM E1426, ASTM, Philadelphia, PA, 2003

  21. Parmar A., Mellor P.B. (1978) Int. J. Mech. Sci., 20:385–91

    Article  Google Scholar 

  22. “Standard Test Method for Plastic Strain Ratio r for Sheet Metal,” ASTM E517, ASTM, Philadelphia, PA, 2000

  23. Parmar A., Mellor P.B. (1978) Int. J. Mech. Sci., 20:707–20

    Article  Google Scholar 

Download references

Author information

Authors and Affiliations

  1. Metallurgy Division, Department of Commence, National Institute of Standards and Technology, Technology Administration, Gaithersburg, MD, 20899, USA

    T. Foecke (Staff Materials Scientist), M.A. Iadicola (Staff Scientists), A. Lin (Guest Researcher) & S.W. Banovic (Staff Scientists)

Authors
  1. T. Foecke
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. M.A. Iadicola
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. A. Lin
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. S.W. Banovic
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to T. Foecke.

Additional information

Manuscript submitted March 21, 2006.

The U.S. Government's right to retain a non-exclusive, royalty-free license in and to any copyright is acknowledged

Rights and permissions

Reprints and permissions

About this article

Cite this article

Foecke, T., Iadicola, M., Lin, A. et al. A Method for Direct Measurement of Multiaxial Stress-Strain Curves in Sheet Metal. Metall Mater Trans A 38, 306–313 (2007). https://doi.org/10.1007/s11661-006-9044-y

Download citation

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s11661-006-9044-y

Keywords

Search

Navigation