Abstract
The manufacture and maintenance of large parts in ships, trains, aircrafts, and so on create an increasing demand for mobile machine tools to perform in-situ operations. However, few mobile robots can accommodate the complex environment of industrial plants while performing machining tasks. This study proposes a novel six-legged walking machine tool consisting of a legged mobile robot and a portable parallel kinematic machine tool. The kinematic model of the entire system is presented, and the workspace of different components, including a leg, the body, and the head, is analyzed. A hierarchical motion planning scheme is proposed to take advantage of the large workspace of the legged mobile platform and the high precision of the parallel machine tool. The repeatability of the head motion, body motion, and walking distance is evaluated through experiments, which is 0.11, 1.0, and 3.4 mm, respectively. Finally, an application scenario is shown in which the walking machine tool steps successfully over a 250 mm-high obstacle and drills a hole in an aluminum plate. The experiments prove the rationality of the hierarchical motion planning scheme and demonstrate the extensive potential of the walking machine tool for in-situ operations on large parts.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Uriarte L, Zatarain M, Axinte D, et al. Machine tools for large parts. CIRP Annals, 2013, 62(2): 731–750
Bostelman R, Hong T, Marvel J. Survey of research for performance measurement of mobile manipulators. Journal of Research of the National Institute of Standards and Technology, 2016, 121: 342–366
Suárez R, Palomo-Avellaneda L, Martinez J, et al. Development of a dexterous dual-arm omnidirectional mobile manipulator. IFAC-PapersOnLine, 2018, 51(22): 126–131
Olazagoitia J L, Wyatt S. New PKM Tricept T9000 and Its Application to Flexible Manufacturing at Aerospace Industry. SAE Technical Paper 2007-01-3820, 2007
Law M, Rentzsch H, Ihlenfeldt S. Development of a dynamic substructuring framework to facilitate in situ machining solutions using mobile machine tools. Procedia Manufacturing, 2015, 1: 756–767
Hazel B, Côté J, Laroche Y, et al. In-situ robotic interventions in hydraulic turbines. In: Proceedings of the 2010 1st International Conference on Applied Robotics for the Power Industry. Montreal: IEEE, 2010, 11637498
Hazel B, Boudreault E, Côté J, et al. Robotic post-weld heat treatment for in situ repair of stainless steel turbine runners. In: Proceedings of the 2014 3rd International Conference on Applied Robotics for the Power Industry. Foz do Iguassu: IEEE, 2014, 14903693
Collado V, Arana J, Saenz A. A Crawling Portable Robot for Drilling Operations in Large Air Frame Components. SAE Technical Paper 2005-01-3337, 2005
Marguet B, Cibiel C, De Francisco Ó, et al. Crawler Robots for Drilling and Fastener Installation: An Innovative Breakthrough in Aerospace Automation. SAE Technical Paper 2008-01-2292, 2008
Pessi P, Wu H, Handroos H, et al. A mobile robot with parallel kinematics to meet the requirements for assembling and machining the ITER vacuum vessel. Fusion Engineering and Design, 2007, 82(15–24): 2047–2054
Irawan A, Nonami K. Optimal impedance control based on body inertia for a hydraulically driven hexapod robot walking on uneven and extremely soft terrain. Journal of Field Robotics, 2011, 28(5): 690–713
Santos P G D, Garcia E, Cobano J A, et al. SIL06: A six-legged robot for humanitarian de-mining tasks. In: Proceedings of World Automation Congress. Seville: IEEE, 2004, 15: 523–528
Kashiri N, Baccelliere L, Muratore L, et al. CENTAURO: A hybrid locomotion and high power resilient manipulation platform. IEEE Robotics and Automation Letters, 2019, 4(2): 1595–1602
Yang H, Krut S, Pierrot F, et al. On the design of mobile parallel robots for large workspace applications. In: Proceedings of ASME 2011 International Design Engineering Technical Conferences and Computers and Information in Engineering Conference. Volume 6: 35th Mechanisms and Robotics Conference, Parts A and B. Washington, D.C.: ASME, 2011, 767–776
Yang H, Krut S, Baradat C, et al. Locomotion approach of REMORA: A reonfigurable mobile robot for manufacturing Applications. In: Proceedings of 2011 IEEE/RSJ International Conference on Intelligent Robots and Systems. San Francisco: IEEE, 2011: 5067–5072
Rushworth A, Axinte D, Raffles M, et al. A concept for actuating and controlling a leg ofa novel walking parallel kinematic machine tool. Mechatronics, 2016, 40: 63–77
Olarra A, Axinte D, Uriarte L, et al. Machining with the WalkingHex: A walking parallel kinematic machine tool for in situ operations. CIRP Annals, 2017, 66(1): 361–364
Li Y G, Liu H T, Zhao X M, et al. Design of a 3-DOF PKM module for large structural component machining. Mechanism and Machine Theory, 2010, 45(6): 941–954
Tunc L T, Shaw J. Experimental study on investigation of dynamics of hexapod robot for mobile machining. International Journal of Advanced Manufacturing Technology, 2016, 84: 817–830
Barnfather J D, Goodfellow M J, Abram T. Positional capability ofa hexapod robot for machining applications. International Journal of Advanced Manufacturing Technology, 2017, 89(1–4): 1103–1111
Huang T, Wang P F, Zhao X M, et al. Design of a 4-DOF hybrid PKM module for large structural component assembly. CIRP Annals, 2010, 59(1): 159–162
Pan Y, Gao F. Kinematic Performance Analysis for Hexapod Mobile Robot Using Parallel Mechanism. In: Proceedings of ASME 2014 International Design Engineering Technical Conferences and Computers and Information in Engineering Conference. Volume 5A: 38th Mechanisms and Robotics Conference. Buffalo: ASME, 2014, V05AT08A089
Chen Z J, Gao F, Pan Y. Novel door-opening method for six-legged robots based on only force sensing. Chinese Journal of Mechanical Engineering, 2017, 30(5): 1227–1238
Zhao Y, Gao F, Hu Y. Novel method for six-legged robots turning valves based on force sensing. Mechanism and Machine Theory, 2019, 133: 64–83
Rao A B K, Rao P V M, Saha S K. Workspace and dexterity analyses of hexaslide machine tools. In: Proceedings of International Conference on Robotics and Automation. Taipei: IEEE, 2003, 3: 4104–4109
BS EN ISO 9283:1998 Manipulating Industrial Robots—Performance Criteria and Related Test Methods. 1998
Acknowledgements
This work was funded by the National Natural Science Foundation of China (Grant No. U1613208), the National Key Research and Development Plan of China (Grant No. 2017YFE0112200), and the European Union’s Horizon 2020 Research and Innovation Programme under the Marie Sklodowska-Curie grant agreement No. 734575.
Author information
Authors and Affiliations
Corresponding author
Electronic supplementary material
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made.
The images or other third party material in this article are included in the article’s Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder.
To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Liu, J., Tian, Y. & Gao, F. A novel six-legged walking machine tool for in-situ operations. Front. Mech. Eng. 15, 351–364 (2020). https://doi.org/10.1007/s11465-020-0594-2
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11465-020-0594-2