Abstract
In this work we investigate the feasibility of two-directional switching of an initially curved or pre-buckled electrostatically actuated microbeams using a single electrode fabricated from the same structural layer. The distributed electrostatic force, which is engendered by the asymmetry of the fringing fields in the deformed state, acts in the direction opposite to the deflection of the beam and can be effectively viewed as a reaction of a nonlinear elastic foundation with stiffness parameterized by the voltage. The reduced order model was built using the Galerkin decomposition with linear undamped modes of a straight beam as base functions and verified using the results of the numerical solution of the differential equation. The electrostatic force was approximated by means of fitting the results of three-dimensional numerical solution of the electrostatic problem. Static stability analysis reveals that the presence of the restoring electrostatic force may result in the suppression of the snap-through instability as well as in the appearance of additional stable configurations associated with higher buckling modes of the beam that are not observed in “mechanically” loaded structures. We show that two-directional switching of a pre-buckled beam between two stable configurations cannot be achieved using quasistatic loading. Furthermore, we show that switching is both associated with the dynamic snap-through mechanism and possible within certain interval of actuation voltages. Using a single-degree-of-freedom (lumped) model, estimation voltage boundaries are obtained. Theoretical results illustrate the feasibility of the suggested operational principle as an efficient mechanism in the arena of non-volatile mechanical memory devices.
Similar content being viewed by others
References
Buchaillot, L., Millet, O., Quévy, E., Collard, D.: Post-buckling dynamic behavior of self-assembled 3D microstructures. Microsyst. Technol. 14, 69–78 (2007)
Casals-Terré, J., Fargas-Marques, A., Shkel, A.M.: Snap-action bistable micromechanisms actuated by nonlinear resonance. J. Microelectromech. Syst. 17, 1082–1093 (2008)
Das, K., Batra, R.C.: Pull-in and snap-through instabilities in transient deformations of microelectromechanical systems. J. Micromech. Microeng. 19, 035008 (2009)
Das, K., Batra, R.C.: Symmetry breaking, snap-through and pull-in instabilities under dynamic loading of microelectromechanical shallow arches. Smart Mater. Struct. 18, 115008 (2009)
Gerson, Y., Krylov, S., Ilic, B.R.: Electrothermal bistability tuning in a large displacement micro-actuator. J. Micromech. Microeng. 20, 112001 (2010)
Krylov, S., Ilic, B.R., Schreiber, D., Seretensky, S., Craighead, H.G.: Pull-in behavior of electrostatically actuated bistable microstructures. J. Micromech. Microeng. 18, 055026 (2008)
Krylov, S., Dick, N.: Dynamic stability of electrostatically actuated initially curved shallow microbeams. Contin. Mech. Thermodyn. 22, 445–468 (2010)
Michael, A., Kwok, C.Y.: Design criteria for bi-stable behavior in a buckled multi-layered MEMS bridge. J. Micromech. Microeng. 16, 2034–2043 (2006)
Pane, I.Z., Asano, T.: Investigation on bistability and fabrication of bistable prestressed curved beam. Jpn. J. Appl. Phys. 47, 5291–5296 (2008)
Ouakad, H.M., Younis, M.I.: The dynamic behavior of MEMS arch resonators actuated electrically. Int. J. Non-Linear Mech. 45, 704–713 (2010)
Qui, J., Lang, J.H., Slocum, A.H.: A curved beam bistable mechanism. J. Microelectromech. Syst. 13, 137–146 (2004)
Seunghoon, P., Dooyoung, H.: Pre-shaped buckled-beam actuators: Theory and experiments. Sens. Actuators A, Phys. 148, 186–192 (2008)
Saif, M.T.A.: On a tunable bistable MEMS—Theory and experiment. J. Microelectromech. Syst. 9, 157–170 (2000)
Sulfridge, M., Saif, T., Miller, N., Meinhart, M.: Nonlinear dynamic study of a bistable MEMS: Model and experiment. J. Microelectromech. Syst. 13, 725–731 (2004)
Vangbo, M., Bäcklund, Y.: A lateral symmetrically bistable buckled beam. J. Micromech. Microeng. 8, 29–32 (1998)
Zhang, Y., Wang, Y., Li, Z., Huang, Y., Li, D.: Snap-through and pull-in instabilities of an arch-shaped beam under an electrostatic loading. J. Microelectromech. Syst. 16, 684–693 (2007)
Charlot, B., Sun, W., Yamashita, K., Fujita, H., Toshiyoshi, H.: Bistable nanowire for micromechanical memory. J. Micromech. Microeng. 18, 045005 (2008)
Halg, B.: On a micro-electro-mechanical nonvolatile memory cell. IEEE Trans. Electron Devices 37, 2230–2236 (1990)
Roodenburg, D., Spronck, J.W., van der Zant, H.S.J., Venstra, W.J.: Buckling beam micromechanical memory with on-chip readout. Appl. Phys. Lett. 94, 183501 (2009)
Rubin, J., Tiwari, S.: An electronic nonvolatile memory device based on electrostatic deflection of a bistable mechanical beam. Tech. Dig. of MRS Fall Meeting, Boston, 27 November–1 December 2006 (oral presentation) O3.10 (2006)
Southworth, D.R., Bellan, L.M., Linzon, Y., Craighead, H.G., Parpia, J.M.: Stress-based vapor sensing using resonant microbridges. Appl. Phys. Lett. 96, 163503 (2010)
Zhao, J., Jia, J., Wang, H., Li, W.: A novel threshold accelerometer with postbuckling structures for airbag restraint systems. IEEE Sens. J. 7(8), 1102–1109 (2007)
Li, H., Balachandran, B.: Buckling and free oscillations of composite microresonators. J. Microelectromech. Syst. 15, 42–51 (2006)
Li, H., Preidikman, S., Balachandran, B., Mote, C.D. Jr.: Nonlinear free and forced oscillations of piezoelectric microresonators. J. Micromech. Microeng. 16, 356–367 (2006)
Li, H., Piekarski, B., DeVoe, D.L., Balachandran, B.: Nonlinear oscillations of piezoelectric microresonators with curved cross sections. Sens. Actuators A, Phys. 144, 194–200 (2008)
Younis, M.I., Ouakad, H.M., Alsaleem, F.M., Miles, R., Cui, W.: Nonlinear dynamics of MEMS arches under harmonic electrostatic actuation. J. Microelectromech. Syst. 19, 647–656 (2010)
Linzon, Y., Krylov, S., Ilic, B., Southworth, D.R., Barton, R.A., Cipriany, B.R., Cross, J.D., Parpia, J.M., Craighead, H.G.: Real-time synchronous imaging of electromechanical resonator mode and equilibrium profiles. Opt. Lett. 35(15), 2654–2656 (2010)
Simitses, G.J., Hodges, D.H.: Fundamentals of Structural Stability. Elsevier, Amsterdam (2006)
Greason, W.D.: Analysis of charged device model (CDM) ESD in MEMS. J. Electrost. 68, 159–167 (2010)
Zhang, W., Turner, K.L.: Application of parametric resonance amplification in a single-crystal silicon micro-oscillator based mass sensor. Sens. Actuators A, Phys. 122, 23–30 (2005)
Turner, K.L., Miller, S.A., Hartwell, P.G., MacDonald, N.C., Strogatz, S.H., Adams, S.G.: Five parametric resonances in a micromechanical system. Nature 36, 149–152 (1998)
Rhoads, J.F., Shaw, S.W., Turner, K.L., Moehlis, J., DeMartini, B.E., Zhang, W.: Generalized parametric resonance in electrostatically actuated microelectromechanical oscillators. J. Sound Vib. 296, 797–829 (2006)
Lee, K.B.: Non-contact electrostatic microactuator using slit structures: Theory and a preliminary test. J. Micromech. Microeng. 17, 2186–2196 (2007)
Siyuan, H., Ridha, B.M.: Design, modeling, and demonstration of a MEMS repulsive-force out-of-plane electrostatic micro actuator. J. Microelectromech. Syst. 17(3), 532–547 (2008)
Hah, D., Patterson, P.R., Nguyen, H.D., Toshiyoshi, H., Wu, M.C.: Theory and experiments of angular vertical comb-drive actuators for scanning micromirrors. IEEE J. Sel. Top. Quantum Electron. 10, 505–513 (2004)
Su, J., Yang, Fay, H.P., Porod, W., Bernstein, G.G.: A surface micromachined offset-drive method to extend the electrostatic travel range. J. Micromech. Microeng. 20, 015004 (2010)
Agache, V., Legrand, B., Nakamura, K., Kawakatsu, H., Buchaillot, L., Toshiyoshi, H., Collard, D., Fujita, H.: Characterization of vertical vibration of electrostatically actuated resonators using atomic force microscope in noncontact mode. In: Proc. of the 13th Intern. Conf. on Solid-State Sensors, Actuators and Microsystems, Seoul, Korea, June 5–9, 2005, pp. 2023–2026 (2005)
Krylov, S., Molinazzi, N., Shmilovich, T., Pomerantz, U., Lulinsky, S.: Parametric excitation of flexural vibrations of microbeams by fringing electrostatic fields. In: Proc. of the ASME 2010 Int. Design Eng. Tech. Conf. and Comp. and Inf. Eng. Conf. IDETC/CIE 2010, August 15–18, 2010, Montreal, Quebec, Canada (2010)
Villagio, P.: Mathematical Models for Elastic Structures. Cambridge University Press, Cambridge (1997)
Chen, J.-S., Liao, C.-Y.: Experiment and analysis on the free dynamics of a shallow arch after an impact load at the end. J. Appl. Mech. 72, 54–61 (2005)
Emam, S.A., Nayfeh, A.H.: On the nonlinear dynamics of a buckled beam subjected to a primary-resonance excitation. Nonlinear Dyn. 35, 1–17 (2004)
Mallon, N.J., Fey, R.H.B., Nijmeijer, H., Zhang, G.Q.: Dynamic buckling of a shallow arch under shock loading considering the effects of the arch shape. Int. J. Non-Linear Mech. 41, 1057–1067 (2006)
Abu-Salih, S., Elata, D.: Experimental validation of electromechanical buckling. J. Microelectromech. Syst. 15(6), 1656–1662 (2006)
Elata, D., Abu-Salih, S.: Analysis of a novel method for measuring residual stress in micro-systems. J. Micromech. Microeng. 15, 921–927 (2005)
Krylov, S., Harari, I., Cohen, Y.: Stabilisation of electrostatically actuated microstructures using parametric excitation. J. Micromech. Microeng. 15(5), 1188–1204 (2006)
Krylov, S.: Parametric excitation and stabilization of electrostatically actuated microstructures. Int. J. Multiscale Comput. Eng. 6(6), 563–584 (2008)
Krylov, S., Gerson, Y., Nahmias, T., Keren, U.: Excitation of large amplitude parametric resonance by the mechanical stiffness modulation of a microstructure. J. Micromech. Microeng. 20, 015041 (2010)
Nayfeh, A.H., Younis, M.I., Abdel-Rahman, E.M.: Reduced-order models for MEMS applications. Nonlinear Dyn. 41, 211–236 (2005)
Bochobza-Degani, O., Elata, D., Nemirovsky, Y.: An efficient DIPIE algorithm for CAD of electrostatically actuated MEMS devices. J. Microelectromech. Syst. 11, 612–620 (2002)
Pelesko, J.A., Bernstein, D.H.: Modeling of MEMS and NEMS. Chapman&Hall, London (2002)
Shampine, L.F., Reichelt, M.W., Kierzenka, J.: Solving Boundary Value Problems for Ordinary Differential Equations in MATLAB with bvp4c. Available at www.mathworks.com/bvp_tutorial
Parnes, R.: Bending of an axially constrained beam. Int. J. Mech. Sci. 13, 285–290 (1970)
Dym, C.L.: Stability Theory and Its Applications to Structural Mechanics. Noordhoff, Leyden (1974)
Bazant, Z.P., Cedolin, L.: Stability of Structures. Elastic, Inelastic, Fracture and Damage Theories. Dover, Mineola (2003)
Simitses, G.J.: Dynamic Stability of Suddenly Loaded Structures. Springer, New York (1989)
Haberman, R., Rand, R., Yuster, T.: Resonant capture and separatrix crossing in dual-spin spacecraft. Nonlinear Dyn. 18, 159–184 (1999)
Haberman, R., Rand, R.: Sequences of orbits and the boundaries of the basin of attraction for two double heteroclinic orbits. Int. J. Non-Linear Mech. 34, 1047–1059 (1999)
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Krylov, S., Ilic, B.R. & Lulinsky, S. Bistability of curved microbeams actuated by fringing electrostatic fields. Nonlinear Dyn 66, 403–426 (2011). https://doi.org/10.1007/s11071-011-0038-y
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11071-011-0038-y