Abstract
Fatigue and fatigue-creep crack growth rate in a bimetal of continuous caster rolls for different loading frequencies and waveforms is investigated with the use of stress, deformation and energy criteria of fracture mechanics.
Similar content being viewed by others
References
L.A. James (1972) ArticleTitleThe effect of frequency upon the fatigue-crack growth of type 304 stainless steel at 1000F ASTM STP 513 218–29
N. Merah T. Bui-Quoc M. Bernard (1999) ArticleTitleCreep-fatigue crack growth in notched SS-304 plates at 600°C Engineering Fracture Mechanics 63 39–55 Occurrence Handle10.1016/S0013-7944(99)00004-1
Y.M. Baik K.S. Kim (2001) ArticleTitleThe combined effect of frequency and load level on fatigue crack growth in stainless steel 304 International Journal of Fatigue 23 417–425 Occurrence Handle10.1016/S0142-1123(00)00109-2
G. Onofrio G.A. Osinkolu M. Marchionni (2004) ArticleTitleEffects of loading waveform on fatigue crack growth of Udimet 720 Li superalloy International Journal of Fatigue 26 203–209 Occurrence Handle10.1016/S0142-1123(03)00170-1
Yasniy P., Maruschak P., Hlado V. (2005). Effect of temperature, frequency and loading waveform on fatigue crack growth in bimaterial of the roll for continuous casting machines. Int. Sci. Conf. Progressives Technologies and Materials, Poland, Rzeszow, 2005, 91-92.
V. Lupinc G. Onofrio (1995) ArticleTitleThe effect of creep and oxidation on high-temperature fatigue crack propagation in (001)-loaded CMSX-2 superalloy single crystals Materials Science and Engineering A202 76–83
Nakayama Y., Miura N., Takahashi Y., Date S., Shimakawa T., Toya Y.( 1998). Development of fatigue and creep crack propagation law for 316FR stainless steel in consideration of FBR operating condition. Fatigue, Facture, and High Тemperature Design Methods in Pressure Vessel and Piping. ASME 365, 191-198.
R. Pippan K. Flechsig F. Riemelmoser (2000) ArticleTitleFatigue crack propagation behavior in the vicinity of an interface between material with different yield stresses Materials Science and Engineering. A 283 225–233 Occurrence Handle10.1016/S0921-5093(00)00703-6
E1290-89 (1992). Standard test method for crack-tip opening displacement (CTOD) fracture toughness measurement.
I. Barsoum K.S. Ravi Chandran (2003) ArticleTitleStress intensity factor solutions for cracks in finite-width three layer laminates with and without residual stress effects Engineering Fracture Mechanics 70 2015–2031 Occurrence Handle10.1016/S0013-7944(02)00260-6
X. Gomez J. Echeberria (2000) ArticleTitleMicrostructure and mechanical properties of low alloy steel T11-austenitic stainless steel 347 bimetallic tubes Materials Science and Technology 16 187–193
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Yasniy, P., Maruschak, P. & Lapusta, Y. Experimental Study of Crack Growth in a Bimetal Under Fatigue and Fatigue-Creep Conditions. Int J Fract 139, 545–552 (2006). https://doi.org/10.1007/s10704-006-0102-7
Issue Date:
DOI: https://doi.org/10.1007/s10704-006-0102-7