Abstract
In this paper, integrated BiCMOS amplifier and current-sensing circuits are introduced for high-performance DC–DC boost converter. By exploiting the advantage of BiCMOS technology, the high gain amplifier and accurately sensed inductor current are obtained in the feedback control circuit. The proposed current-sensing circuit adopts a current-mirror instead of op-amplifier as a voltage follower so that it would reduce power consumption with a smaller chip-size. Bipolar transistor is also applied in the differential pair and current sources of the error amplifier to obtain a fast transient response. Frequency response shows the amplifier gain with the compensator affects significantly on the stability of the converter. The chip is fabricated in 0.35 µm 2-poly 4-metal BiCMOS process. The measurement shows that the current-sensing circuit can operate with accuracy of higher than 90 % at the frequency from 10 to 200 kHz and the transient time of the error amplifier is controlled within 10 µs. The converter with chip-size of 1 mm2 operates at the output voltage of 4.5–9 V with the frequency of 0.01–1 MHz.
Similar content being viewed by others
References
Leung, C. F., Mok, P., & Leung, K. (2005). A 1-V integrated current-mode boost converter in standard 3.3/5-V CMOS technologies. IEEE Journal of Solid-State Circuits, 40(11), 2265–2274.
Lee, C. S., Kim, N. S. & Ko, H. H. (2011) Integrated 0.35 μm BiCMOS DC–DC boost converter. IEEE International Symposium. EMS 2011 (pp. 462–467).
Tao, X., & Xu, J. (2008). Integrated current-sensing circuit with offset-current cancellation for boost converters. IEEE International Conference on Communications, Circuits and Systems, 2008, 1328–1331.
Corsi, M. (1995). Current sensing schemes for use in BiCMOS integrated circuits. In Proceedings of the IEEE Bipolar/BiCMOS circuits and technology meeting, New York (pp. 55–57).
Lee, C. S., Kim, N. S., Gendensuren, M., Choi, J. H., & Choi, J. H. (2012). Integrated on-chip 0.35 μm BiCMOS current-mode DC–DC buck converter. International Journal of Electronics, 99(12), 1623–1634.
Cheng, K. H., Su, C. W., & Ko, H. H. (2008). A high-accuracy and high-efficiency on-chip current sensing for current-mode control CMOS DC–DC buck converter. IEEE International Conference on Electronics, Circuits, and Systems, 2008, 458–461.
Meyer, R. G., & Mack, D. (1994). A 1-GHz BiCMOS RF front-end IC. IEEE Journal of Solid-State Circuits, 29(3), 350–355.
Roh, J. (2005). High-performance error amplifier for fast transient DC–DC converters. IEEE Transactions on Circuits and Systems-II, 52(9), 591–595.
Erickson, R. W., & Maksimovic, D. (2001). Fundamentals of power electronics. Norwell: Kluwer.
Forghani-zadeh, H. P., & Rincon-Mora, G. A. (2007). An accurate, continuous, and lossless self-learning CMOS current-sensing scheme for inductor-based DC–DC converters. IEEE Journal of Solid-State Circuits, 42(3), 665–679.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Lee, CS., Ko, HH. & Kim, NS. Integrated current-mode DC–DC boost converter with high-performance control circuit. Analog Integr Circ Sig Process 80, 105–112 (2014). https://doi.org/10.1007/s10470-014-0310-4
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s10470-014-0310-4