Abstract
Recycling of printed circuit boards (PCBs) is complicated by the presence of flame retardants containing halogen and phosphorus, as the degradation products of these retardants reduce the quality of the produced gases and liquids. Moreover, during thermal treatment, corrosive and toxic compounds are released and the volatilization of undesirable metals incorporated in the PCB matrix is enhanced. To combat this problem, we investigated the effects of calcium hydroxide (Ca(OH)2) on the thermal decomposition of both phenol and epoxy resin paper-laminated PCBs containing tetrabromobisphenol-A. Pyrolysis experiments revealed a maximum removal of 94 % HBr, 98 % brominated phenols, and 98 % phosphorus from the gaseous and liquid pyrolysis products. In addition, Br-induced metal volatilization was inhibited, improving the recovery amount in the solid fraction. Thermogravimetry–mass spectrometry revealed that Ca(OH)2 enhanced the evolution of phenolic compounds produced from the PCB matrix, mainly below 300 °C, while the fixation of brominated compounds took place primarily above 300 °C.
Similar content being viewed by others
References
Huisman J (2012) Eco-efficiency evaluation of WEEE take-back systems. Waste electrical and electronic equipment (WEEE) handbook, pp 93–119
Veit HM, Diehl TR, Salami AP, Rodrigues JS, Bernardes AM, Tenorio JA (2005) Utilization of magnetic and electrostatic separation in the recycling of printed circuit boards scrap. Waste Manag 25:67–74
Zhu P, Chen Y, Wang LY, Qian GY, Zhou M, Zhou J (2012) A new technology for separation and recovery of materials from waste printed circuit boards by dissolving bromine epoxy resins using ionic liquid. J Hazard Mater 239–240:270–278
Chen Y, Chen Z, Xiao S, Liu H (2008) A novel thermal degradation mechanism of phenol–formaldehyde type resins. Thermochim Acta 476:39–43
Wang J, Jiang H, Jiang N (2009) Study on the pyrolysis of phenol-formaldehyde (PF) resin and modified PF resin. Thermochim Acta 496:136–142
Barontini F, Cozzani V (2006) Formation of hydrogen bromide and organobrominated compounds in the thermal degradation of electronic boards. J Anal Appl Pyro 77:41–55
Grause G, Furusawa M, Okuwaki A, Yoshioka T (2008) Pyrolysis of tetrabromobisphenol-A containing paper laminated printed circuit boards. Chemosphere 71:872–878
Barontini F, Cozzani V, Marsanich K, Raffa V, Petarca L (2004) An experimental investigation of tetrabromobisphenol A decomposition pathways. J Anal Appl Pyro 72:41–53
Barontini F, Marsanich K, Petarca L, Cozzani V (2004) The thermal degradation process of tetrabromobisphenol A. Ind Eng Chem Res 43:1952–1961
Luda MP, Balabanovich AI, Zanetti M (2010) Pyrolysis of fire retardant anhydride-cured epoxy resins. J Anal Appl Pyro 88:39–52
Terakado O, Ohhashi R, Hirasawa M (2011) Thermal degradation study of tetrabromobisphenol A under the presence metal oxide: comparison of bromine fixation ability. J Anal Appl Pyro 91:303–309
Terakado O, Ohhashi R, Hirasawa M (2013) Bromine fixation by metal oxide in pyrolysis of printed circuit board containing brominated flame retardant. J Anal Appl Pyro 103:216–221
Bhaskar T, Tanabe M, Muto A, Sakata Y (2006) Pyrolysis study of a pvdc and hips-br containing mixed waste plastic stream: effect of the poly(ethylene terephthalate). J Anal Appl Pyro 77:68–74
Bhaskar T, Matsui T, Kaneko J, Uddin MA, Muto A, Sakata Y (2002) Novel calcium based sorbent (Ca–C) for the dehalogenation (Br, Cl) process during halogenated mixed plastic (PP/PE/PS/PVC and HIPS-Br) pyrolysis. Green Chem 4:372–375
Martin-Sampedro R, Eugenio ME, Moreno JA, Revilla E, Villar JC (2014) Integration of a kraft pulping mill into a forest biorefinery: pre-extraction of hemicellulose by steam explosion versus steam treatment. Bioresour Technol 153:236–244
Kumagai S, Grause G, Kameda T, Yoshioka T (2014) Simultaneous recovery of benzene-rich oil and metals by steam pyrolysis of metal-poly(ethylene terephthalate) composite waste. Environ Sci Technol 48:3430–3437
Montaudo G, Samperi F, Montaudo MS (2006) Characterization of synthetic polymers by MALDI-MS. Prog Polym Sci 31:277–357
Grause G, Kärrbrant R, Kameda T, Yoshioka T (2014) Steam hydrolysis of poly(bisphenol a carbonate) in a fluidized bed reactor. Ind Eng Chem Res 53:4215–4223
Kumagai S, Grause G, Kameda T, Takano T, Horiuchi H, Yoshioka T (2011) Decomposition of gaseous terephthalic acid in the presence of CaO. Ind Eng Chem Res 50:1831–1836
Grause G, Karakita D, Kameda T, Bhaskar T, Yoshioka T (2012) Effect of heating rate on the pyrolysis of high-impact polystyrene containing brominated flame retardants: fate of brominated flame retardants. J Mater Cycles Waste Manag 14:259–265
Zhang Q, Saito F, Ikoma T, Tero-Kubota S (2001) Effects of quartz addition on the mechanochemical dechlorination of chlorobiphenyl by using Cao. Environ Sci Technol 35:4933–4935
Zecchina A, Stone FS (1986) Adsorption and reaction of pyridine on alkaline earth oxides as studied by UV–visible diffuse reflectance spectroscopy. J Catal 101:227–237
Wang Z, Wang F, Cao J, Wang J (2010) Pyrolysis of pine wood in a slowly heating fixed-bed reactor: potassium carbonate versus calcium hydroxide as a catalyst. Fuel Process Technol 91:942–950
Shen DK, Gu S (2009) The mechanism for thermal decomposition of cellulose and its main products. Bioresour Technol 100:6496–6504
Lu Q, X-C Yang, C-Q Dong, Z-F Zhang, X-M Zhang, X-F Zhu (2011) Influence of pyrolysis temperature and time on the cellulose fast pyrolysis products: analytical Py-GC/MS study. J Anal Appl Pyro 92:430–438
Patwardhan PR, Dalluge DL, Shanks BH, Brown RC (2011) Distinguishing primary and secondary reactions of cellulose pyrolysis. Bioresour Technol 102:5265–5269
Wang S, Guo X, Liang T, Zhou Y, Luo Z (2012) Mechanism research on cellulose pyrolysis by Py-GC/MS and subsequent density functional theory studies. Bioresour Technol 104:722–728
Chu PP, H-D Wu, Lee C-T (1998) Thermodynamic properties of novolac-type phenolic resin blend with poly(ethylene oxide). J Polym Sci Part B 36:1647–1655
Wang F-Y, Ma CCM, Wu W-J (1999) Kinetic parameters of thermal degradation of polyethylene glycol-toughened novolac-type phenolic resin. J Appl Polym Sci 80:188–196
Cornelis G, Van Gerven T, Vandecasteele C (2012) Antimony leaching from MSWI bottom ash: modelling of the effect of pH and carbonation. Waste Manag 32:278–286
Lin Y-C, Cho J, Tompsett GA, Westmoreland PR, Huber GW (2009) Kinetics and mechanism of cellulose pyrolysis. J Phys Chem C 113:20097–20107
Ogata M, Kinjo N, Eguchi S, Kawata T, Urano T (1990) Effects of the molecular weights of raw epoxy resins on the physical properties of cured epoxy resins. Kobunshi Ronbunshu 47:639–647
Balabanovich AI, Hornung A, Merz D, Seifert H (2004) The effect of a curing agent on the thermal degradation of fire retardant brominated epoxy resins. Polym Degrad Stab 85:713–723
Acknowledgments
This work was partially supported by the Japanese Ministry of Education, Culture, Sports, Science, and Technology (MEXT) Grant-in-Aid for Scientific Research (A) (25241022).
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Kumagai, S., Grause, G., Kameda, T. et al. Thermal decomposition of tetrabromobisphenol-A containing printed circuit boards in the presence of calcium hydroxide. J Mater Cycles Waste Manag 19, 282–293 (2017). https://doi.org/10.1007/s10163-015-0417-4
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s10163-015-0417-4