Abstract
Improving fracture performance and sintering procedure of alumina/silicon carbide nano ceramic is considered. To do this, some experimental variables such as sintering conditions and silicon carbide volume fraction were optimized. In this study, several tests were conducted on the nano ceramic samples which prepared in different conditions to achieve the best fracture properties. The main concern is the properties which are important against projectile impacts. Flexural strength, fracture toughness, Vickers hardness, and energy dissipation factor for different samples were measured, and optimum sintering conditions were obtained.
Similar content being viewed by others
References
Nazari A, Abdinejad VR (2012) Artificial neural networks for prediction Charpy impact energy of Al6061/SiCp-laminated nanocomposites. Neural Comput Appl. doi:10.1007/s00521-012-0996-0
Wang HZ, Gao L, Guo JK (2000) The effect of nanoscale SiC particles on the microstructure of AlZ03 ceramics. Ceram Int 26:391–396
Seong-Min C, Hideo A (2005) Nanocomposites-a new material design concept. Sci Technol Adv Mater 6:2–10
Pezzoti G, Muller WH (2001) Strengthening mechanisms in Alz03/SiC nanocomposites. Comput Mater Sci 22:155–168
Medvedovski E (2006) Alumina-mullite ceramics for structural applications. Ceram Int 32:369–375
Neshpor VC, Zaitsev GP, DovgaI EJ, et al (1994) Armour ceramics ballistic efficiency evaluation. In: Proceedings of the 8th CIMTEC on ceramics: charting the future (Ed. P. Vincenzini), Florence, Italy, 2395–2401 (Technas.r.l)
Kinsler LE, Frey AR, Coppens AB, Sanders JV (2000) Fundamentals of acoustics, 4th edn. Wiley, New York
Wang J, Lim SY, Ng SC, Chew CH, Gan LM (1998) Dramatic effect of a small amount of MgO addition on the sintering of Alz03-5 vol % SIC nanocomposite. Mater Lett 33:273–277
Rittidech A, Portia L, Bongkarn T (2006) The relationship between microstructure and mechanical properties of Al2O3MgO ceramics. Mater Sci Eng A 438–440:395–398
Niihara K, Nakahira A (1988) Strengthening of oxide ceramics by SiC and Si3Ni4 dispersion. In: Proceedings of the 3rd international symposium on ceramic materials and components for engines 3rd international symposium, Las Vegas, pp 27–30, 919–926
Wang HZ, Gao L, Gui LH, Guo JK (1998) Preparation and properties of intragranular Al2O3- SiC nanocomposites. Nanostruct Mater 10(6):947–953
ASTM B311-93 (2002) Test method for density determination for powder metallurgy (P/M) materials containing less than two percent porosity, developed by Subcommittee, B09.11. Book of Standards, 02.05
ASTM C1161-02c (2008) Standard test method for flexural strength of advanced ceramics at ambient temperature, developed by Subcommittee, C28.01. Book of Standards, 15.01
ASTM C1327-08 (2008) Standard test method for Vickers indentation hardness of advanced ceramics, developed by Subcommittee, C28.01. Book of Standards, 15.01
ASTM C790-07 (2007) Standard test method for flexural properties of unreinforced and reinforced plastics and electrical insulating materials, developed by Subcommittee, C20.10, Book of Standards, 08.01
Anatis GR, Chantikul P, Lawn BR, Marshall DB (1981) A critical evaluation of indention techniques for measuring fracture toughness: I, direct crack measurements. J Am Ceram Soc 64:533–538
Asadi A, Sadough A, Jabbari A (2011) Heat treatment of Al2O3-SiC-MgO nanoceramic and optimizing the fracture performance. Int J Physical Sci 6:5253–5260
Asadi A, Sadough A, Jabbari A (2011) Investigation of the impact behavior of A12O3-SiC-MgO nanoceramic/metal laminated composite. J Mech Sci Technol 25:2179–2184
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Kordani, N., vanini, A.S., Asadi, A. et al. Optimization of fracture behavior of alumina/silicon carbide nano ceramic. Neural Comput & Applic 23, 2379–2385 (2013). https://doi.org/10.1007/s00521-012-1195-8
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00521-012-1195-8