Abstract
The authors report on laser micro-cutting results for stainless steel foils with the aid of a 100 W fiber laser. This novel laser source combines a high output power in relation to conventional laser sources for micro-processing applications with an excellent beam quality (M2=1.1). Different material thicknesses were evaluated (100 μm to 300 μm). Processing was carried out with cw operation of the laser source, and with nitrogen and oxygen as assisting gases. Besides the high processing rate of oxygen assisted cutting, a better cutting performance in terms of a lower kerf width was obtained.
Similar content being viewed by others
References
F. Röser, A. Liem, S. Höfer, H. Zellmer, S. Nolte, J. Limpert, A. Tünnermann, T. Schreiber, J. Phys. B 38, 681 (2005)
J. Limpert, H. Zellmer, U. Griebnera, S. Unger, G. Korna, D. Nickel, A. Liem, A. Tünnermann, Opt. Commun. 1–6, 309 (2001)
V. Reichel, J. Kirchhof, H. Bartelt, H.-R. Müller, K. Mörl, S. Unger, EPS-QEOD Europhoton Conf. on Solid-State and Fiber Coherent Light Sources (2004)
D. Burns, A.J. Kemp, G.J. Valentine, Prog. Quantum Electron. 28, 205 (2004)
J. Canning, Opt. Laser. Eng. 44, 647 (2006)
H. Zellmer, A. Tünnermann, J. Limpert, A. Liem, Electron. Lett. 39, 1460 (2003)
V. Gapontsev, in LASE 2004 (Photonics West, San Jose, CA)
A.A. Isineev, V.B. Kravchenko, V.P. Gapontsev, S.M. Matitsin, Opt. Laser Technol. 14, 189 (1982)
J.H. Sahu, J. Nilsson, D.J. Richardson, W.A. Clarkson, C.C. Renaud, J.A. Alvarez-Chavez, Conf. on Lasers and Electro-Optics (Optic. Soc. Amer., 2001)
A.G. Getman, A.B. Rulkov, S.V. Popov, J.R. Taylor, V.P. Gapontsev, A.V. Avdokhin, M.Y. Vyatkin, Adv. Solid-State Photonics, 19th Topical Meeting (2004)
F. Vollertsen, F. Wagner, M. Grupp, in Proc. LIM2005 (BLZ, 2005), pp. 769–772
H. Hügel, Opt. Laser. Eng. 34, 213 (2000)
H. Rohde, in Microcutting of Metals with Pulsed Nd:YAG Lasers, 1st edn. (Ready, Orlando, FL, USA, 2001), pp. 448–450
H.J. Booth, Thin Solid Films 453–454, 450 (2004)
K. Dickmann, M. Baumeister, Appl. Phys. A 81, 561 (2005)
K. Dickmann, M. Baumeister, in Proc. of the LiM (2005)
B. Whitney, Y.-C. Ku, J. Fox, K. Kleine, S. Jones, US Patent (2005)
T. Hoult, R. Press, Photonics Spectra (Laurin Publishing Co., Inc., Pittsfield, MA, USA, 2005), pp. 46–47
C. Engineer, D. Kothwala, A. Raval, A. Choubey, Mater. Sci. Eng. A 386, 331 (2004)
D. Petring, PhD thesis (RWTH Aachen, 1995)
Author information
Authors and Affiliations
Corresponding author
Additional information
PACS
42.82.Cr; 42.62.Cf; 81.05.Bx
Rights and permissions
About this article
Cite this article
Baumeister, M., Dickmann, K. & Hoult, T. Fiber laser micro-cutting of stainless steel sheets. Appl. Phys. A 85, 121–124 (2006). https://doi.org/10.1007/s00339-006-3687-9
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00339-006-3687-9