Abstract
The mechanical strength properties of the branchwood of Aningeria robusta and Terminalia ivorensis with diameters ranging from 10 to 25 cm were examined to determine the suitability of branchwood as raw material for downstream processing. The study precisely assessed the static bending strengths, compression strengths and shear strengths parallel to the grain of the branchwood and stemwood of T. ivorensis and A. robusta. It was observed that under static bending, the overall (sapwood and heartwood combined) modulus of rupture and modulus of elasticity of the branchwood of A. robusta and T. ivorensis were lower than that of their corresponding stemwood. The results further show that the overall compression and shear strengths parallel to the grain of the branchwood of A. robusta and T. ivorensis were higher than that of their corresponding stemwood. Under static bending, compression parallel to the grain, and shear parallel to the grain, the experimental results indicate that the sapwood of the branchwood from both T. ivorensis and A. robusta had lower strength values than that of their corresponding heartwood. Similar results were recorded for the stemwood of T. ivorensis where the heartwood had higher strength values than the sapwood. However, in the case of the stemwood of A. robusta, the sapwood had higher strength values than the corresponding heartwood.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Adam AR, Ofosu-Asiedu A, Dei Amoah C, Asante Asiamah A (1993) Wood waste and logging damage in Akuse and Afram Headwaters Forest Reserve. In: Report of ITTO project PD 74/90. Better utilization of tropical timber resources in order to improve sustainability and reduce negative ecological impact. FORIG, Kumasi, pp 46–51
British Standard Institution (1957) British Standard 373:1957. Testing small clear specimens of timber. BSI, London
Clarke SH (1937) The distribution, structure and properties of tension wood in beech (Fagus sylvatica L.) Forestry 11:85–91
Ishengoma RC, Nagoda L (1991) Solidwood: physical and mechanical properties, defects, grading and utilisation as fuel. University of Norway, pp123–151
Koch P (1964) Wood machining process. Ronald Press, pp 74–76
Metten CJ (1986) Structural timber design technology. Longman scientific and technical longman group UK. Longman House, Burnt Hill, England, pp 16–17
Okai R, Frimpong-Mensah K, Yeboah D (2003) Characterization of moisture content and specific gravity of branchwood and stemwood of Aningeria robusta and Terminalia ivorensis. Holz Roh Werkstoff 61:155–158
Panshin A, De Zeew C (1980) Textbook of wood technology, 4th edn. McGraw-Hill, New York
Pillow MY (1950) The presence of tension wood in Mahogany in relation to longitudinal shrinkage. US Forest Product Laboratory. Report no. D1763
Stalnaker JJ, Harris EC (1989) Structural design in wood structural engineering series. Van Nostrand Reinhold, New York, pp 120–127
Zenker R, Muller-Stoll WR (1966) Einfluss der Zugholzfasern auf die Festigkeiteigenschaften des Pappelholzes in nassem und trockenem Zustand. Holztechnologie 7:17–25
Acknowledgement
The authors wish to express their appreciation to the International Tropical Timber Organization (ITTO) for funding this work. Appreciation is also extended to the Technicians of the Engineering and Mechanical Processing Division of the Forestry Research Institute of Ghana (FORIG) for their assistance in conducting the experiment.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Okai, R., Frimpong-Mensah, K. & Yeboah, D. Characterization of strength properties of branchwood and stemwood of some tropical hardwood species. Wood Sci Technol 38, 163–171 (2004). https://doi.org/10.1007/s00226-004-0232-x
Received:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00226-004-0232-x