Skip to main content
SpringerLink
Log in

Accelerated aging investigation of silicone rubber/silica composites for coating of high-voltage insulators

  • Original Paper
  • Published:
Electrical Engineering Aims and scope Submit manuscript

Abstract

Room temperature vulcanized silicone rubber (RTV-SiR) is a prominent polymeric material for coating of high-voltage insulators. Like other polymeric materials, silicone rubber also exhibits aging in outdoor applications. Silica is one of the most effective additives for properties’ enhancement of polymeric materials. To analyze the effect of silica on the aging behavior of RTV-SiR, we prepared its two silica-based composites with 10% micro \(+\)5% nano and 15% microsilica. Prepared samples are subjected to accelerated stresses such as ultraviolet radiation, acid rain, heat, and fog for 9000 h in a specially fabricated chamber. For timely analysis of the samples, scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), leakage current monitoring and Swedish Transmission Research Institute hydrophobicity analyses are used along with continuous visual inspection. In the course of time, all samples showed gradual decrease in transparency. Increase in leakage current was highest in case of the neat SiR (SiR-0) and lowest in case of the hybrid composite (SiR-2). Initial values of leakage current for SiR-0, SiR-1 and SiR-2 were 0.5, 0.5 and 0.3 \(\upmu \)A, respectively, and after aging the increased leakage current values were 0.9, 0.8 and 0.6 \(\upmu \)A. From FTIR, the lowest decrease in the intensities of absorption peaks of important groups in SiR-2 were recorded. In SiR-0, the peaks of symmetric C–H stretching of \(\hbox {CH}_{3}\) and Si–\(\hbox {CH}_{3}\) symmetric bending after 9000 h were 91.7 and 94.6% of virgin, respectively. In SiR-1 and SiR-2, symmetric C–H stretching of \(\hbox {CH}_{3}\) exhibited an increase which was 120 and 110%, respectively, while Si–\(\hbox {CH}_{3}\) symmetric bending remained 95% of virgin in SiR-1 and nearly 97% in SiR-2 after 9000 h. Final hydrophobicities of SiR-0 and SiR-1 were HC-2, while comparatively SiR-1 had higher hydrophobicity class of HC-1. SEM results also exposed least changes in the surface of hybrid composite. Silica revealed great impact on the aging behavior of silicone rubber which was highest in the case of the hybrid composite.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10

Similar content being viewed by others

References

  1. Hawley KA (1931) Development of the Porcelain Insulator. Trans Am Inst Electr Eng 50(1):47–51

    Article  Google Scholar 

  2. Mackevich J, Shah M (1997) Polymer outdoor insulating materials. Part I: comparison of porcelain and polymer electrical insulation. IEEE Electr Insul Mag 13(3):5–12

    Article  Google Scholar 

  3. Yang L, Hao Y, Li L, Zhao Y (2012) Comparison of pollution flashover performance of porcelain long rod, disc type, and composite UHVDC insulators at high altitudes. IEEE Trans Dielectr Electr Insul 19(3):1053–1059

    Article  Google Scholar 

  4. Gorur RS, Cherney E, de Tourreil C, Dumora D, Harmon R, Hervig H, Tay R (1995) Protective coatings for improving contamination performance of outdoor high voltage ceramic insulators. IEEE Trans Power Deliv 10(2):924–933

    Article  Google Scholar 

  5. Tocháček J, Vrátníčková Z (2014) Polymer life-time prediction: the role of temperature in UV accelerated ageing of polypropylene and its copolymers. Polym Test 36:82–87

    Article  Google Scholar 

  6. Li Z, Moon KS, Yao Y, Hansen K, Watkins K, Morato L, Wong CP (2013) Carbon nanotube/polymer nanocomposites: sensing the thermal aging conditions of electrical insulation components. Carbon 65:71–79

    Article  Google Scholar 

  7. Wang W, Yue C, He D, Yang K, Chen S (2014) A comparative analysis of dielectric properties of oil–paper insulation and polymer materials before and after thermal aging. Sci China Technol Sci 57(4):738–746

    Article  Google Scholar 

  8. Amin M, Amin S (2014) Aging research on SiR And TPE insulators (an overview). Rev Adv Mater Sci 36:29–39

    Google Scholar 

  9. Pickett JE, Coyle DJ (2013) Hydrolysis kinetics of condensation polymers under humidity aging conditions. Polym Degrad Stab 98(7):1311–1320

    Article  Google Scholar 

  10. Amin M, Akbar M, Matsuoka R (2006) Effect of UV_radiation, temperature and SALT Fog on polymeric insulators. In: IEEE 8th international conference on properties & applications of dielectric materials, IEEE, pp 611–614

  11. Deroiné M, Le Duigou A, Corre YM, Le Gac PY, Davies P, César G, Bruzaud S (2014) Accelerated ageing and lifetime prediction of poly (3-hydroxybutyrate-co-3-hydroxyvalerate) in distilled water. Polym Test 39:70–78

    Article  Google Scholar 

  12. Cangialosi D, Boucher VM, Alegría A, Colmenero J (2013) Physical aging in polymers and polymer nanocomposites: recent results and open questions. Soft Matter 9(36):8619–8630

    Article  Google Scholar 

  13. Marzec A, Laskowska A, Boiteux G, Zaborski M, Gain O, Serghei A (2014) Study on weather aging of nitrile rubber composites containing imidazolium ionic liquids. In: Macromolecular symposia, vol 342, No 1, pp 25–34

  14. Vilar G, Fernández-Rosas E, Puntes V, Jamier V, Aubouy L, Vázquez-Campos S (2013) Monitoring migration and transformation of nanomaterials in polymeric composites during accelerated aging. J Phys Conf Ser 429(1):012044 (IOP Publishing)

  15. Zhu YJ, Zhang J, Jing B, Tan YB (2013) Ageing effect on steady rheological behavior in oilfield water of water-soluble, hydrophobically associating polymer. Adv Mater Res 781:431–435 (Trans Tech Publications)

  16. Manfred W, Siegfried N (1961) U.S. Patent No. 2,999,077. U.S. Patent and Trademark Office, Washington, DC

  17. Grill A, Patel VV, Gates SM (2002) U.S. Patent No. 6,479,110. U.S. Patent and Trademark Office, Washington, DC

  18. Braley S (1968) The silicones as subdermal engineering materials. Ann N Y Acad Sci 146(1):148–157

    Article  Google Scholar 

  19. Reynders JP, Jandrell IR, Reynders SM (1999) Review of aging and recovery of silicone rubber insulation for outdoor use. IEEE Trans Dielectr Electr Insul 6(5):620–631

    Article  Google Scholar 

  20. Meguriya N (2003) U.S. Patent No. 6,552,096. U.S. Patent and Trademark Office, Washington, DC

  21. Nakamura T, Hirabayashi S (1996) U.S. Patent No. 5,582,885. U.S. Patent and Trademark Office, Washington, DC

  22. Shimizu K, Watanabe T, Hamada M (1982) U.S. Patent No. 4,360,566. U.S. Patent and Trademark Office, Washington, DC

  23. Brown JB, Fryer MP, Randall P, Lu M (1953) Silicones in plastic surgery: laboratory and clinical investigations, a preliminary report. Plast Reconstr Surg 12(5):374–376

    Article  Google Scholar 

  24. Lothongkam C, Siebler D, Heidmann G, Plath R, Gockenbach E (2014) The influence of thermal aging on AC dielectric strength of transparent silicone rubbers for HV insulation. In: Proceedings of 2014 international symposium on electrical insulating materials (ISEIM), IEEE, pp 346–349

  25. Bian S, Jayaram S, Cherney EA (2012) Electrospinning as a new method of preparing nanofilled silicone rubber composites. IEEE Trans Dielectr Electr Insul 19(3):777–785

    Article  Google Scholar 

  26. Kim SH, Cherney EA, Hackam R (1991) Suppression mechanism of leakage current on RTV coated porcelain and silicone rubber insulators. IEEE Trans Power Deliv 6(4):1549–1556

    Article  Google Scholar 

  27. Vas JV, Venkatesulu B, Thomas MJ (2012) Tracking and erosion of silicone rubber nanocomposites under DC voltages of both polarities. IEEE Trans Dielectr Electr Insul 19(1):91–98

    Article  Google Scholar 

  28. Bian S, Jayaram SH, Cherney EA (2012) Improvements to the erosion resistance of nanofilled silicone rubber composites by electrospinning. In: 2012 Annual report conference on electrical insulation and dielectric phenomena (CEIDP), IEEE, pp 741–744

  29. Amin M (2013) Methods for preparation of nano-composites for outdoor insulation applications. Rev Adv Mater Sci 34:173–184

    Google Scholar 

  30. Saldivar-Guerrero R, Hernández-Corona R, Lopez-Gonzalez FA, Rejón-García L, Romero-Baizabal V (2014) Application of unusual techniques for characterizing ageing on polymeric electrical insulation. Electr Power Syst Res 117:202–209

    Article  Google Scholar 

  31. Seyedmehdi SA, Zhang H, Zhu J (2012) Superhydrophobic RTV silicone rubber insulator coatings. Appl Surf Sci 258(7):2972–2976

    Article  Google Scholar 

  32. Du BX, Li ZL (2015) Hydrophobicity, surface charge and DC flashover characteristics of direct-fluorinated RTV silicone rubber. IEEE Trans Dielectr Electr Insul 22(2):934–940

    Article  Google Scholar 

  33. Momen G, Farzaneh M (2011) Survey of micro/nano filler use to improve silicone rubber for outdoor insulators. Rev Adv Mater Sci 27(1):1–13

    Google Scholar 

  34. Fabiani D, Montanari GC, Krivda A, Schmidt LE, Hollertz R (2010) Epoxy based materials containing micro and nano sized fillers for improved electrical characteristics. In: 2010 10th IEEE international conference on solid dielectrics, IEEE, pp 1–4

  35. Anhalt M, Weidenfeller B (2011) Influence of filler content, particle size and temperature on thermal diffusivity of polypropylene-iron silicon composites. J Appl Polym Sci 119(2):732–735

    Article  Google Scholar 

  36. El-Hag AH, Jayaram SH, Cherney EA (2004) Comparison between silicone rubber containing micro-and nano-size silica fillers [insulating material applications]. In: 2004 Annual report conference on electrical insulation and dielectric phenomena, 2004. CEIDP’04, IEEE, pp 385–388

  37. El-Hag AH, Simon LC, Jayaram SH, Cherney EA (2006) Erosion resistance of nano-filled silicone rubber. IEEE Trans Dielectr Electr Insul 13(1):122–128

    Article  Google Scholar 

  38. Du BX, Han T, Su JG (2014) Tree characteristics in silicone rubber/SiO\(_{2}\) nanocomposites under low temperature. IEEE Trans Dielectr Electr Insul 21(2):503–510

    Article  Google Scholar 

  39. Du BX, Li ZL (2014) Surface charge and dc flashover characteristics of direct-fluorinated SiR/SiO\(_{2}\) nanocomposites. IEEE Trans Dielectr Electr Insul 21(6):2602–2610

    Article  Google Scholar 

  40. Du BX, Han T, Su JG (2014) Effect of low temperature on tree characteristics in silicone rubber with different power frequency. IEEE Trans Dielectr Electr Insul 21(4):1880–1886

    Article  Google Scholar 

  41. Dimitropoulou M, Pylarinos D, Siderakis K, Thalassinakis E, Danikas M (2015) Comparative investigation of pollution accumulation and natural cleaning for different HV insulators. Eng Technol Appl Sci Res 5(2):764

    Google Scholar 

  42. Khattak A, Iqbal M, Amin M, Aging analysis of high voltage silicone rubber/silica nanocomposites under accelerated weathering conditions. Sci Eng Compos Mater (in press)

  43. Khattak A, Amin M (2016) Accelerated aging investigation of high voltage EPDM/silica composite insulators. J Polym Eng 36(2):199–209

    Article  Google Scholar 

  44. Schneider HM, Guidi WW, Burnham JT, Gorur RS, Hall JF (1993) Accelerated aging and flashover tests on 138 kV nonceramic line post insulators. IEEE Trans Power Deliv 8(1):325–336

    Article  Google Scholar 

  45. Chen Z, Rao Z, Lin C, Chen C, Jia Z, Lu H, Yang Z (2014) Non-destructive condition assessment of silicone rubber composite insulators. In: 2014 IEEE conference on electrical insulation and dielectric phenomena (CEIDP), IEEE, pp 494–497

  46. Olave C, Trinidad P, Molina I, Sundararajan R (2005) Influence of acid rain + multistress conditions on the long term performance of 28 kV polymeric insulators. In: CEIDP’05. 2005 Annual report conference on electrical insulation and dielectric phenomena, 2005, IEEE, pp 341–344

  47. Guide STRI (1992) Hydrophobicity classification guide. Guide 1(92):1

    Google Scholar 

  48. Kim JH (1999) Hydrophobicity loss and recovery of silicone HV insulation. IEEE Trans Dielectr Electr Insul 6(5):695–702

    Article  MathSciNet  Google Scholar 

  49. Meyer LH, Cabral SH, Araújo E, Cardoso G, Liesenfeld N (2006) Use of nano-silica in silicone rubber for ceramic insulators coatings in coastal areas. In: Conference record of the 2006 IEEE international symposium on electrical insulation, 2006, IEEE, pp 474–477

  50. Kumagai S, Yoshimura N (2000) Evaluation of leakage current on various types of polymeric materials used for HV outdoor insulation in salt-fog condition. Trans Inst Electr Eng Jpn A Publ Fundam Mater Soc 120(11):1051–1055

  51. Rajini V, Udayakumar K (2009) Degradation of silicone rubber under AC or DC voltages in radiation environment. IEEE Trans Dielectr Electr Insul 16(3):834–841

    Article  Google Scholar 

  52. Ramirez-Vazquez I, Nava R (2013) Application of nano particles for the modification of high voltage insulators. IEEE Trans Dielectr Electr Insul 20(6):2262–2269

    Article  Google Scholar 

  53. Zhuravlev LT (1989) Structurally bound water and surface characterization of amorphous silica. Pure Appl Chem 61(11):1969–1976

    Article  Google Scholar 

  54. Khan Y, Al-Arainy AA, Malik NH, Qureshi MI, Al-Ammar AE (2010) Loss and recovery of hydrophobicity of EPDM insulators in simulated arid desert environment. In: Power and energy engineering conference (APPEEC), IEEE, pp 1–4

  55. Rajkumar K, Dwivedi C, Thavamani P, Jeyanthi P, Pazhanisamy P (2013) Effect of nanosilica on ethylene propylene Diene monomer rubber nanocomposites. Int J Innov Res Dev 2(5):831–841

  56. Okel TA, Waddell WH (1995) Effect of precipitated silica physical properties on silicone rubber performance. Rubber Chem Technol 68(1):59–76

    Article  Google Scholar 

Download references

Author information

Authors and Affiliations

  1. Department of Electrical Engineering, Ghulam Ishaq Khan Institute (GIKI) of Engineering Sciences and Technology, Topi, Pakistan

    Muhammad Amin

  2. Department of Electrical Engineering, COMSATS Institute of Information Technology (CIIT), Wah, Pakistan

    Abraiz Khattak

  3. Department of Electrical Engineering, City University of Science and IT (CUSIT), Peshawar, Pakistan

    Abraiz Khattak

  4. Department of Electrical Engineering, University of Engineering and Technology (UET), Taxila, Pakistan

    Muhammad Ali

Authors
  1. Muhammad Amin
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Abraiz Khattak
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Muhammad Ali
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Abraiz Khattak.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Amin, M., Khattak, A. & Ali, M. Accelerated aging investigation of silicone rubber/silica composites for coating of high-voltage insulators. Electr Eng 100, 217–230 (2018). https://doi.org/10.1007/s00202-016-0498-7

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s00202-016-0498-7

Keywords

Search

Navigation