Abstract
The wear of micro-grinding tools less than 1 mm in diameter is crucial for achieving acceptable surface quality and accurate dimension of the workpiece. To control wear behavior of the micro-grinding tools, an investigation through experiments was conducted on the machining and wear performance of various (D-shaped PCD, CVD, electroless plated, and electroplated) diamond micro-grinding tools on monocrystalline silicon workpiece in this study. The experiments showed that a CVD diamond micro-grinding tool had excellent machining performance, but its relatively large diameter limited its application range. An electroplated diamond micro-grinding tool had a good machining performance but displayed severe wear. To comprehensively understand its wear mechanism, a series of grinding experiments were further done. Its mechanism was analyzed through investigating the tool and machining process parameters. In order to accurately evaluate tool wear, the ratio of tool radius loss to average grain diameter (δ) and the ratio of the lost grain number to the total grain number (η) were proposed. The δ-ratio and η-ratio related to the wear limit of 600 mesh size micro-grinding tools having a diameter of 0.5 mm were 0.16–0.18 and 11.50–13.88%, respectively.
Similar content being viewed by others
References
Li W, Liu M, Ren YH, Chen QD (2019) A high-speed precision micro-spindle use for mechanical micro-machining. Int J Adv Manuf Technol 102(9-12):3197–3211
Chen S, Shen B, Chen Y et al (2017) Synergistic friction-reducing and anti-wear behaviors of graphene with micro-and nano-crystalline diamond films. Diam Relat Mater 73:25–32
Pratap A, Patra K, Dyakonov AA (2019) A comprehensive review of micro-grinding: emphasis on toolings, performance analysis, modeling techniques, and future research directions. Int J Adv Manuf Technol 104(1-4):63–102
Li W, Li ZP, Ren YH, Huang XM (2018) Error analysis of high-speed precision micro-spindle equipped with micro-tool in mechanical micro-grinding. Int J Adv Manuf Technol 97(1-4):599–609
Morgan CJ, Vallance RR, Marsh ER (2004) Micro machining glass with polycrystalline diamond tools shaped by micro electro discharge machining. J Micromech Microeng 14(12):1687–1692
Wei CJ, Hu DJ, Xu KZ et al (2011) Electrochemical discharge dressing of metal bond micro-grinding tools. Int J Mach Tool Manu 51(2):165–168
Aurich JC, Engmann J, Schueler GM et al (2009) Micro grinding tool for manufacture of complex structures in brittle materials. CIRP Ann Manuf Technol 58(1):311–314
Chen ST, Tsai MY, Lai YC et al (2009) Development of a micro diamond grinding tool by compound process. J Mater Process Technol 209(10):4698–4703
Arrabiyeh PA, Kirsch B, Aurich JC (2016) Development of micro pencil grinding tools via an electroless plating process. J Micro Nano Manuf 5(1):011002
Gäbler J, Pleger S (2010) Precision and micro CVD diamond-coated grinding tools. Int J Mach Tool Manu 50(4):420–424
Zhang Q, Zhao Q, To S et al (2017) Diamond wheel wear mechanism and its impact on the surface generation in parallel diamond grinding of RB-SiC/Si. Diam Relat Mater 74:16–23
Mao C, Zhang YC, Peng XX et al (2018) Wear mechanism of single cBN-WC-10Co fiber cutter in machining of Ti-6Al-4V alloy. J Mater Process Technol 259:45–57
Shen JY, Wang JQ, Jiang B et al (2015) Study on wear of diamond wheel in ultrasonic vibration-assisted grinding ceramic. Wear 332-333:788–793
Dai C, Ding W, Xu J et al (2017) Influence of grain wear on material removal behavior during grinding nickel-based superalloy with a single diamond grain. Int J Mach Tool Manu 113:49–58
Linke BS (2015) Review on grinding tool wear with regard to sustainability. J Manuf Sci Eng Trans ASME 137(6):060801
Li W, Zhou ZX, Yin SH et al (2016) Research status analysis and review of micro-grinding technology and micro-grinding machines. Aust J Mech Eng 52(17):10–19
Feng J, Kim BS, Shih A et al (2009) Tool wear monitoring for micro-end grinding of ceramic materials. J Mater Process Technol 209(11):5110–5116
Perveen A, Jahan MP, Rahman M et al (2012) A study on microgrinding of brittle and difficult-to-cut glasses using on-machine fabricated poly crystalline diamond (PCD) tool. J Mater Process Technol 212(3):580–593
Wen XL, Gong YD (2017) Modeling and prediction research on wear of electroplated diamond micro-grinding tool in soda lime glass grinding. Int J Adv Manuf Technol 91(9-12):3467–3479
Cheng J, Gong YD (2014) Experimental study of surface generation and force modeling in micro-grinding of single crystal silicon considering crystallographic effects. Int J Mach Tool Manu 77:1–15
Mao C, Zhou FJ, Hu YL et al (2019) Tribological behavior of cBN-WC-10Co composites for dry reciprocating sliding wear. Ceram Int 45:6447–6458
Acknowledgements
We also thank Ning He and Xiuqing Hao (Nanjing University of Aeronautics and astronautics), Tianfeng Zhou, and Qian Yu (Beijing Institute of Technology) for their assistance in fabricating micro-grinding tools.
Funding
The presented work was funded by the National Science Foundation of China (51675170, 51875192), China Postdoctoral Science Foundation (2016T90749, 2015M570676), and Fundamental Research Funds for the Central Universities. The authors acknowledge the financial supports.
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher’s note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Li, W., Ren, Y., Li, C. et al. Investigation of machining and wear performance of various diamond micro-grinding tools. Int J Adv Manuf Technol 106, 921–935 (2020). https://doi.org/10.1007/s00170-019-04610-4
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-019-04610-4