Abstract
The machining of a cone frustum as specified on the ISO 10791-7 standard is a widely accepted test to evaluate the performance of five-axis machining centers. By measuring the cross-sectional circularity of the cone, the contouring accuracy of a five-axis CNC machine tool can be assessed. A reduction of circularity is directly related to the improvement of the contouring accuracy in circular motions. The contouring accuracy can also be assessed by measuring the circularity of the circular motion path described by the tool center point of a five-axis CNC machine tool. A better circular tool center path entails an enhancement on the circularity of the traversal sections of the cone frustum. The majority of CNC actuators are AC servomotors that are precisely controlled via two closed loops: one for position and one for velocity. The circular contouring accuracy of a five-axis CNC machine tool can be improved by adjusting the loop gains and time constant of the velocity loop integration. Although higher gains enable the servomotors to attain the desired positions faster, the resulting contouring accuracy may not be satisfactory. Furthermore, excessively high gains could cause vibrations. The objective of this research is to establish a frequency domain approach for tuning the control parameters for each motion axis such that their frequency responses are matched within a range of frequencies, reducing the circularity value of the cross sections of a cone frustum. Results demonstrate the effect of tuning the control loop parameters based on the frequency response of each axis. Case studies were conducted to determine the variation in the circularity value when the control parameters of each axis were tuned to obtain similar frequency responses to the linear and rotary axes within a frequency range. Rates of improvement greater than 80% were achieved after using the proposed method to tune the control parameters of each motion axis.
Similar content being viewed by others
References
Hong C, Ibaraki S, Matsubara A (2011) Influence of position-dependent geometric errors of rotary axes on a machining test of cone frustum by five-axis machine tools. Precis Eng 35(1):1–11
Givi M, Mayer JRR (2016) Optimized volumetric error compensation for five-axis machine tools considering relevance and compensability. CIRP J Manuf Sci Technol 12:44–55
Lei WT, Paung IM, Yu CC (2009) Total ballbar dynamic tests for five-axis CNC machine tools. Int J Mach Tools Manuf 49(6):488–499
Tsutsumi M, Tone S, Kato N, Sato R (2013) Enhancement of geometric accuracy of five-axis machining centers based on identification and compensation of geometric deviations. Int J Mach Tools Manuf 68:11–20
Sato R, Nishio K, Shirase K, Campatelli G, Scippa A (2014) Influence of motion error of translational and rotary axes onto machined surface generated by simultaneous five-axis motion. In: Procedia CIRP. pp 269–274
Kato N, Tsutsumi M, Tsuchihashi Y, Sato R, Ihara Y (2013) Sensitivity analysis in ball bar measurement of three-dimensional circular movement equivalent to cone-frustum cutting in five-axis machining centers. J Adv Mech Des Syst Manuf 7(3):317–332
Yang SM, Lin KW (2016) Automatic control loop tuning for permanent-magnet AC servo motor drives. IEEE Trans Ind Electron 63(3):1499–1506
Kuo LY, Yen JY (2002) A genetic algorithm-based parameter-tuning algorithm for multi-dimensional motion control of a computer numerical control machine tool. Proc Inst Mech Eng B J Eng Manuf 216(3):429–438
Wang SM, Ouh SC, Yen CT (2014) An adaptive parameter tuning method with on-machine weight identification function for CNC machine tools. Appl Mech Mater 479-480:268–273
Ikegami T, Hirogaki T, Aoyama E (2016) Development of automatic servo tuning function in rotary axis with DDM for machine tools and its performance for stable machining. Mater Sci Forum 874:511–516
Kim D, Son DH, Jeon D (2012) Feed-system autotuning of a CNC machining center: rapid system identification and fine gain tuning based on optimal search. Precis Eng 36(2):339–348
Chang WY, Wu SJ (2016) Big data analysis of a mini three-axis CNC machine tool based on the tuning operation of controller parameters. Int J Adv Manuf Technol:1–7
Suzuki T, Akai T, Aoyama E, Ikegami T, Hirogaki T, Ogawa K (2015) Motion tuning method of linear axes and rotary axis under a constant cutting speed vector at end-milling point with a five-axis controlled machining center. In: ASME 2015 international mechanical engineering congress and exposition, IMECE 2015. American Society of Mechanical Engineers (ASME)
Lin MT, Wu SK (2013) Modeling and analysis of servo dynamics errors on measuring paths of five-axis machine tools. Int J Mach Tools Manuf 66:1–14
Lin MT, Wu SK (2013) Modeling and improvement of dynamic contour errors for five-axis machine tools under synchronous measuring paths. Int J Mach Tools Manuf 72:58–72
Sato R, Tsutsumi M (2012) Motion control techniques for synchronous motions of translational and rotary axes. Procedia CIRP 1:265–270
Sato R, Tsutsumi M (2011) Dynamic synchronous accuracy of translational and rotary axes. Int J Mechatron Manuf Syst 4(3–4):201–219
Lee K, Kim J (2000) Controller gain tuning of a simultaneous multi-axis PID control system using the Taguchi method. Control Eng Pract 8(8):949–958
Yeh SS, Hsu PL (2004) Perfectly matched feedback control and its integrated design for multi-axis motion systems. J Dyn Syst-T ASME 126(3):547–557
Yeh SS, Su SC (2010) Motion parameter tuning for servomotor packs based on learning automata method. J Chin Inst Eng 33(7):961–974
Ibaraki S, Sawada M, Matsubara A, Matsushita T (2010) Machining tests to identify kinematic errors on five-axis machine tools. Precis Eng 34(3):387–398
Standardization IOF (2014) ISO 10791–7: test conditions for machining centers – part 7: accuracy of finished test pieces. Geneva, Switzerland
Kato N, Tsutsumi M, Sato R (2013) Analysis of circular trajectory equivalent to cone-frustum milling in five-axis machining centers using motion simulator. Int J Mach Tools Manuf 64:1–11
Acknowledgements
This project was supported in part by the Ministry of Science and Technology, Taiwan, under Contract MOST104-2221-E-027-132 and MOST103-2218-E-009-027-MY2.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Hidalgo, D., Yeh, SS. Development of an analyzing and tuning technology for improving circularity of cone-frustum motions of five-axis CNC machine tools. Int J Adv Manuf Technol 97, 3283–3297 (2018). https://doi.org/10.1007/s00170-018-2156-x
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-018-2156-x