Abstract
Ball end magnetorheological finishing (BEMRF) is a novel method for nanofinishing of ferromagnetic as well as nonmagnetic materials. With increasing demands of precision finished products in various markets, the quality of surface finish and production rate are of prime importance. For products having complex geometries, this need intensifies as the manual finishing methods are incapable of producing uniform finish throughout the complex geometry of the surface. This paper describes the finishing of 3D surfaces using five-axis CNC BEMRF process in a fully automated manner such that a uniform finish is obtained throughout the workpiece. This eliminates the labor-intensive efforts and the subjective errors involved in manual finishing operations and increases the production rate of the finished products. A customized five-axis CNC controller is developed that enables the sequential and precise control of motion as well as process parameters in the BEMRF machine. The magnetizing current which governs the forces responsible for finishing in BEMRF process is controlled in-process through CNC part program using a specially defined “E” code for magnetizing current. A dedicated graphical user interface is also developed in Visual C# for the control of BEMRF process, enabling the user to make use of BEMRF machine without going into the complexities of the system. Using the customized five-axis CNC controller, automated finishing of a freeform mild steel workpiece is done. The finishing results obtained by the automated five-axis BEMRF machine shows uniformly finished surface profile (up to order of nanometer) on the mild steel test specimen.
Similar content being viewed by others
References
Singh AK, Jha S, Pandey PM (2011) Design and development of nanofinishing process for 3D surfaces using ball end MR finishing tool. Int J Mach Tool Manuf 51(2):142–151. https://doi.org/10.1016/j.ijmachtools.2010.10.002
Singh AK, Jha S, Pandey PM (2012) Magnetorheological ball end finishing process. Mater Manuf Process 27(4):389–394. https://doi.org/10.1080/10426914.2011.551911
Singh AK, Jha S, Pandey PM (2012) Nanofinishing of a typical 3D ferromagnetic workpiece using ball end magnetorheological finishing process. Int J Mach Tool Manuf 63:21–31. https://doi.org/10.1016/j.ijmachtools.2012.07.002
Saraswathamma K, Jha S, Rao PV (2015) Experimental investigation into ball end magnetorheological finishing of silicon. Precis Eng 42:218–223. https://doi.org/10.1016/j.precisioneng.2015.05.003
Singh AK, Jha S, Pandey PM (2012) Nanofinishing of fused silica glass using ball-end magnetorheological finishing tool. Mater Manuf Process 27(10):1139–1144. https://doi.org/10.1080/10426914.2011.654159
Khan DA, Alam Z, Jha S (2016) Nanofinishing of copper using ball end magnetorheological finishing (BEMRF) process, Proceedings of the ASME 2016 International Mechanical Engineering Congress and Exposition. https://doi.org/10.1115/IMECE2016-65974
Beverly CR, Tanner RI (1992) Numerical analysis of three-dimensional Bingham plastic flow. J Non-Newtonian Fluid Mech 42(1-2):85–115. https://doi.org/10.1016/0377-0257(92)80006-J
Alam Z, Jha S (2017) Modeling of surface roughness in ball end magnetorheological finishing (BEMRF) process. Wear 374-375C:54–62. https://doi.org/10.1016/j.wear.2016.11.039
Sidpara AM, Jain VK (2012) Nanofinishing of freeform surfaces of prosthetic knee implant. Proc Inst Mech Eng B J Eng Manuf 226(11):1833–1846. https://doi.org/10.1177/0954405412460452
Kumar S, Jain VK, Sidpara A (2015) Nanofinishing of freeform surfaces (knee join implant) by rotational-magnetorheological abrasive flow finishing (R-MRAFF) process. Precis Eng 42:165–178. https://doi.org/10.1016/j.precisioneng.2015.04.014
Nagdeve L, Jain VK, Ramkumar J (2016) Experimental investigations into nano-finishing of freeform surfaces using negative replica of the knee joint. Procedia CIRP 42:793–798. https://doi.org/10.1016/j.procir.2016.02.321
Iqbal F, Jha S (2017) Nanofinishing of free form surfaces using BEMRF. In: Jain VK (ed) Nanofinishing science and technology: basic and advanced finishing and polishing processes. CRC press, Florida
Jha S, Jain VK (2006) Nano-finishing techniques. In: Mahalik NP (ed) Micromanufacturing and nanotechnology. Springer, Berlin. https://doi.org/10.1007/3-540-29339-6_8
Sidpara A, Jain VK (2013) Analysis of forces on the freeform surface in magnetorheological fluid based finishing process. Int J Mach Tools Manuf 69:1–10. https://doi.org/10.1016/j.ijmachtools.2013.02.004
Bi ZM (2011) Development and control of a 5-axis reconfigurable machine tool. J Robot 583072:9. https://doi.org/10.1155/2011/583072
Park S, Kim SH, Cho H (2006) Kernel software for efficiently building, reconfiguring, and distributing an open CNC controller. Int J Adv Manuf Technol 27(7-8):788–796. https://doi.org/10.1007/s00170-004-2243-z
Hu T, Zhang C, Liu R, Li P (2009) Design and implementation of an open CNC core at the shop floor level. Int J Adv Manuf Technol 40(5-6):541–552. https://doi.org/10.1007/s00170-007-1365-5
Parker Hannifin (2009) ComACRServer6 user’s guide. http://divapps.parker.com/divapps/emn/pdf/ACR/ComACRServer6_User_Guide.pdf. Accessed 9 June 2016
Huo D, Cheng K, Wardle F (2010) Design of a five-axis ultra-precision micro-milling machine—UltraMill. Part 1: holistic design approach, design considerations and specifications. Int J Adv Manuf Technol 47(9-12):867–877. https://doi.org/10.1007/s00170-009-2128-2
Alam Z, Iqbal F, Jha S (2015) Automated control of three axis CNC ball end magneto-rheological finishing machine using PLC. Int J Autom Control 9(3):201–210. https://doi.org/10.1504/IJAAC.2015.070956
Stradling AW (1993) The physics of open-gradient dry magnetic separation. Int J Miner Process 39:19–29
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Alam, Z., Iqbal, F., Ganesan, S. et al. Nanofinishing of 3D surfaces by automated five-axis CNC ball end magnetorheological finishing machine using customized controller. Int J Adv Manuf Technol 100, 1031–1042 (2019). https://doi.org/10.1007/s00170-017-1518-0
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-017-1518-0