Abstract
This paper is motivated by the fact that machining of Inconel 718 involves rapid tool wear and poor surface integrity. We investigate the performance of ceramic cutting inserts in turning of Inconel 718 by virtue of two different assisted machining conditions, plasma preheating- and cryogenic cooling-assisted technologies. The plasma nozzle placed in front of the cutting zone is used to soften the materials before machining. The liquid nitrogen flow located in the cutting area is used to reduce the cutting temperatures in the contact area. The cutting experiments are set for reducing tool wear and improving surface integrity, including surface roughness and micro-hardness beneath workpiece surface. With these two assisted techniques, the tool wear including flank wear and notch wear and the surface microstructure including surface roughness and micro-hardness are assessed and compared with conventional machining. Tool wear reduction and surface integrity improvement can be obtained with these two assisted technologies in turning of Inconel 718 with ceramic cutting inserts. The main causation of notch wear of the ceramic cutting inserts may be the hardened layer beneath the surface. By comparing these two assisted cutting techniques with opposite effects on the cutting tool and workpiece, it has been found that the surface roughness is reduced by 50 %, the micro-hardness is smaller, and the tool life is extended up to more than 40 % over conventional machining.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Rahman M, Seah W, Teo T (1997) The machinability of Inconel 718. J Mater Process Technol 63(1):199–204
Liao Y, Lin H, Wang J (2008) Behaviors of end milling Inconel 718 superalloy by cemented carbide tools. J Mater Process Technol 201(1):460–465
Ezugwu E (2005) Key improvements in the machining of difficult-to-cut aerospace superalloys. Int J Mach Tools Manuf 45(12):1353–1367
Altin A, Nalbant M, Taskesen A (2007) The effects of cutting speed on tool wear and tool life when machining Inconel 718 with ceramic tools. Mater Des 28(9):2518–2522
Zhu D, Zhang X, Ding H (2013) Tool wear characteristics in machining of nickel-based superalloys. Int J Mach Tools Manuf 64:60–77
Lo Casto S, Lo Valvo E, Lucchini E, Maschio S, Piacentini M, Ruisi V (1999) Ceramic materials wear mechanisms when cutting nickel-based alloys. Wear 225:227–233
Hong X (1990) Wear behaviour and wear mechanism of ceramic tools in machining hardened alloy steel. Wear 139(2):439–451
Brandt G (1986) Flank and crater wear mechanisms of alumina-based cutting tools when machining steel. Wear 112(1):39–56
Fan Y, Hao Z, Zheng M, Sun F, Yang S (2013) Study of surface quality in machining nickel-based alloy Inconel 718. Int J Adv Manuf Technol 69(9–12):2659–2667
Sun S, Brandt M, Dargusch M (2010) Thermally enhanced machining of hard-to-machine materials—a review. Int J Mach Tools Manuf 50(8):663–680
Novak J, Shin Y, Incropera F (1997) Assessment of plasma enhanced machining for improved machinability of Inconel 718. J Manuf Sci Eng 119(1):125–129
Kong X, Yang L, Zhang H, Zhou K, Wang Y (2014) Cutting performance and coated tool wear mechanisms in laser-assisted milling K24 nickel-based superalloy. Int J Adv Manuf Technol. 77(9-12):1–13
Vagnorius Z, Sørby K (2011) Effect of high-pressure cooling on life of SiAlON tools in machining of Inconel 718. Int J Adv Manuf Technol 54(1–4):83–92
De Lacalle LL, Sánchez J, Lamikiz A, Celaya A (2004) Plasma assisted milling of heat-resistant superalloys. J Manuf Sci Eng 126(2):274–285
Anderson M, Patwa R, Shin YC (2006) Laser-assisted machining of Inconel 718 with an economic analysis. Int J Mach Tools Manuf 46(14):1879–1891
Yildiz Y, Nalbant M (2008) A review of cryogenic cooling in machining processes. Int J Mach Tools Manuf 48(9):947–964
Wang Z, Rajurkar K (2000) Cryogenic machining of hard-to-cut materials. Wear 239(2):168–175
Wang Z, Rajurkar K, Fan J, Lei S, Shin Y, Petrescu G (2003) Hybrid machining of Inconel 718. Int J Mach Tools Manuf 43(13):1391–1396
Kaynak Y (2014) Evaluation of machining performance in cryogenic machining of Inconel 718 and comparison with dry and MQL machining. Int J Adv Manuf Technol 72(5–8):919–933
Khamsehzadeh H (1991) Behaviour of ceramic cutting tools when machining superalloys. PhD Thesis, University of Warwick
Senthil Kumar A, Raja Durai A, Sornakumar T (2006) Wear behaviour of alumina based ceramic cutting tools on machining steels. Tribol Int 39(3):191–197
Senthil Kumar A, Raja Durai A, Sornakumar T (2006) The effect of tool wear on tool life of alumina-based ceramic cutting tools while machining hardened martensitic stainless steel. J Mater Process Technol 173(2):151–156
Aruna M, Dhanalaxmi V, Mohan S (2010) Wear analysis of ceramic cutting tools in finish turning of Inconel 718. Int J Eng Sci Technol 2(9):4253–4262
Bushlya V, Zhou J, Avdovic P, Ståhl J-E (2013) Wear mechanisms of silicon carbide-whisker-reinforced alumina (Al2O3–SiC w) cutting tools when high-speed machining aged Alloy 718. Int J Adv Manuf Technol 68(5–8):1083–1093
Ståhl JE (2012) Metal cutting—theories and models. Seco Tools, Fargesta, Lund
Zhuang K, Zhu D, Zhang X, Ding H (2014) Notch wear prediction model in turning of Inconel 718 with ceramic tools considering the influence of work hardened layer. Wear 313(1):63–74
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Zhuang, K., Zhang, X., Zhu, D. et al. Employing preheating- and cooling-assisted technologies in machining of Inconel 718 with ceramic cutting tools: towards reducing tool wear and improving surface integrity. Int J Adv Manuf Technol 80, 1815–1822 (2015). https://doi.org/10.1007/s00170-015-7153-8
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-015-7153-8