Abstract
The effect of stability of the body-centered cubic (bcc) β phase on the dynamic fracture behavior of Ti-6Al-4V alloy at room temperature and 77 K has been studied. The presence of a highly unstable β phase in the quenched alloy leads to a decrease in both the dynamic fracture toughness and the crack propagation energy, and this decrease bccomes more pronounced when test temperature is reduced to 77 K. Somewhat improved fracture characteristics were obtained by applying anneal procedure to receive a fully stable β phase. The highest fracture toughness as well as the greatest crack propagation resistance were observed in the air-cooled grade, where the lattice parameter of the bcc phase was intermediate between those pertaining to quenched and annealed Ti-6Al-4V alloys. The effect is attributed to the vanadium content in the β phase, which is sufficiently high to suppress deformation-induced transformation. On the other hand, the V content should be low enough to retard ductile-brittle transition, typical for the bcc metals at cryogenic temperatures. As a result, marked toughening can be achieved, so that the lowest application temperature of high-strength titanium alloys containing the bcc phase can be decreased significantly.
Similar content being viewed by others
References
R.L. Tobler and R.P. Reed:Advances Cryogenic Engineering Materials, Plenum Press, New York, NY, 1982, vol. 28, pp. 83–92.
J. Charles, A. Lutts, and A. Berghezan:Advances Cryogenic Engineering Materials, Plenum Press, New York, NY, 1982, vol. 28, pp. 105–14.
R.P. Reed:Austenitic Steels at Low Temperatures, Plenum Press, New York, NY, 1983, pp. 41–67.
T. Kobayashi and H. Yamamoto:Metall. Trans. A, 1988, vol. 19A, pp. 319–27.
M. Niinomi, T. Kobayashi, I. Inagaki, and A.W. Thompson:Metall. Trans. A, 1990, vol. 21A, pp. 1733–44.
C.J. Guntner and R.P. Reed:Trans. ASM, 1962, vol. 55, pp. 399–419.
T.W. Duerig, G.T. Terlinde, and J.C. Williams:Metall. Trans. A, 1980, vol. 11A, pp. 1987–98.
T. Kobayashi, M. Niinomi, Y. Koide, and K. Matsunuma:Trans. Jpn. Inst. Met., 1986, vol. 27, pp. 775–83.
M.A. Imam and CM. Gilmore:Metall. Trans. A, 1983, vol. 14A, pp. 233–40.
V.S. Tomsinsky, M.I. Shyshkina, and L.L. Ershova:Technol. Legkich Splavov, 1974, (10), pp. 35–39 (in Russian).
B. Hadjsassi and P. Lehr:Mec. Mater. Electr., 1977, vol. 60, pp. 3–13.
M. Grujicic and C.P. Narayan:Mater. Sci. Eng., 1992, vol. A151, pp. 217–26.
T. Kobayashi:Eng. Fract. Mech., 1984, vol. 19, pp. 67–79.
T. Kobayashi, I. Yamamoto, and M. Niinomi:Eng. Fract. Mech., 1986, vol. 24, pp. 773–82.
S. Glazunov and B. Kolachev, eds.:Metallographyya Titanoveach Splavov, Metallurgy, Moscow, 1980, p. 87 (in Russian).
T. Kobayashi, K. Takai, and H. Maniwa:Trans. ISM, 1967, vol. 7, pp. 115–25.
T. Tsuchida and H. Kosuge:Science and Technology of Light Alloys, 1991, The Japan Institute of Light Alloys, Tokyo, pp. 211–16.
D.A. Wigley:Mechanical Properties of Materials at Low Temperatures, Plenum Press, New York, NY, 1971, p. 332.
H. Albert and I. Pfeiffer:Z. Metallkd., 1976, vol. 67, pp. 356–60.
J.L. Murray:Phase Diagrams of Binary Titanium Alloys, ASM INTERNATIONAL, Metal Park, OH, 1990, p. 325.
C.R. Brooks:Heat Treatment, Structure and Properties of Nonferrous Alloys, ASM, Metals Park, OH, 1982.
S. HanActa, T. Yoshio, K. Nishimura, and O. Izumi:Proc. Sixth World Conf. on Titanium, Cannes, 1988, P. Lacombe, R. Tricot, and G. Beranger, eds., pp. 105–10.
S.G. Fedotov:Titanium Science and Technology, Plenum Press, New York, NY, 1973, pp. 871–81.
J.H. bcchtold:Acta Metall., 1955, vol. 3, pp. 249–54.
S. HanActa and O. Izumi:Metall. Trans. A, 1987, vol. 18A, pp. 265–71.
W.M. Garrison, Jr., N.R. Moody:J. Phys. Chem. Solids, 1987, vol. 48 (11), pp. 1035–74.
Standard Method of Test for Elastic-Plastic Fracture Toughness, JSME, Tokyo, 1981, JSME 001-1981, p. 67 (in Japanese).
Z. Nishiyama:Martensitic Transformation, Academic Press, New York, NY, 1978, p. 269.
T.W. Duerig, J. Albrecht, D. Riechter, and P. Fischer:Acta Metall., 1982, vol. 30, pp. 2161–72.
M. Young, E. Levine, and H. Margolin:Metall. Trans., 1974, vol. 5, pp. 1891–98.
H.J. Rack, D. Kalish, and K.D. Fike:Mater. Sci. Eng., 1970, vol. 5, pp. 181–98.
A.I.P. Nwobu, H.F. Flower, and D.R.F. West:Proc. Sixth World Conf. on Titanium, Cannes, 1988, P. Lacombe, R. Tricot, and G. Beranger, eds., pp. 1583–87.
S. Ishiyama, S. HanActa, and O. Izumi:ISU Int., 1991, vol. 31 (8), pp. 807–13.
G.T. Gray, III and P.S. Follansbee:Proc. Sixth World Conf. on Titanium, Cannes, 1988, P. Lacombe, R. Tricot, and G. Beranger, eds., pp. 117–22.
Author information
Authors and Affiliations
Additional information
Formerly Assistant Professor, Department of Production Systems Engineering, Toyohashi University of Technology
Rights and permissions
About this article
Cite this article
Akmoulin, I.A., Niinomi, M. & Kobayashi, T. Dynamic fracture behavior of Ti-6Al-4V alloy with various stabilities of βphase. Metall Mater Trans A 25, 1655–1666 (1994). https://doi.org/10.1007/BF02668531
Received:
Issue Date:
DOI: https://doi.org/10.1007/BF02668531