Abstract
Disappointing results for total ankle replacement have been explained by poor knowledge of the mechanics of the intact and replaced joints. Dynamic simulation tools have the capacity to simulate dynamic conditions that occur in human joints. The Working Model 2D tool was used to simulate the mechanics of the intact and replaced ankle joints, based on previously validated mathematical models. Elementary objects were used to model ligaments, articular surfaces, retinacula and muscle-tendon units. The performance of several pairs of prosthetic articular surfaces was also analysed. According to the results of these simulations, rolling as well as sliding motion occurs in the natural ankle, governed by a ligamentous linkage. Elongation of the tibiocalcaneal and calcaneofibular ligaments was found to be 1.5% and 4.8%, respectively. A 13% change in lever arm length occurred for both the tibialis anterior and gastrocnemius muscles during ankle flexion. Unlike the currently available three-component designs, the newly proposed convex-tibial ligament-compatible prosthesis was found to be able to restore the original mobility and physiological function of the ligaments. This prosthesis combines freedom from restraint with congruity of the components throughout the range of flexion.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Bauer, G., andKinzl, L. (1996): ‘Arthrodesis of the ankle joint’,Orthopade,25, pp. 158–165
Buechel, F. F., Pappas, M. J., andIorio, L. I. (1988): ‘New Jersey low contact stress total ankle replacement: Biomechanical rationale and review of 23 cementeless cases’,Foot Ankle,8, pp. 279–290
Calderale, P. M., Garro, A., Barbiero, R., Fasolio, G., andPipino, F. (1983): ‘Biomechanical design of the total ankle prosthesis’,Eng. Med.,12, pp. 69–80
Charlebois, S. J., andDiAngelo, D. J. (1997a): ‘Development of a linkage model to study the role of the cruciate and collateral ligaments of the knee’. Proceedings of the 21st Annual Meeting of American Society of Biomechanics, Clemson University, South Carolina
Charlebois, S. J., andDiAngelo, D. J. (1997b): ‘Computer simulation studies of ACL loading mechanics’. Proceedings of the 21st Annual Meeting of the American Society of Biomechanics, Clemson University, South Carolina
DiAngelo, D. J., Foley, K. T., Vossel, K. A., Rampersaud, Y. R., andJansen, T. H. (2000): ‘Anterior cervical plating reverses load transfer through multilevel strut-grafts’,Spine,25, pp. 783–795
Foley, K. T., DiAngelo, D. J., Rampersaud, Y. R., Vossel, K. A., andJansen, T. H. (1999): ‘Thein vitro effects of instrumentation on multilevel cervical strut-graft mechanics’,Spine,24, pp. 2366–2376
Garcia, M., Chatterjee, A., Ruina, A., andColeman, M. (1998): ‘The simplest walking model: stability, complexity, and scaling’,J. Biomech. Eng.,120, pp. 281–288
Giannini, S., Leardini, A., andO'Connor, J. J. (2000): ‘Total ankle replacement: review of the designs and of the current status’,Foot Ankle Surg.,6, pp. 77–88
Godest, A. C., De Cloke, C. S., Taylor, M., Gregson, P. J., Keane, A. J., Sathasivan, S., andWalker, P. S. (2000): ‘A computational model for the prediction of total knee replacement kinematics in the sagittal plane’,J. Biomech.,33, pp. 435–442
Goodfellow, J. W., andO'Connor, J. J. (1978): ‘The mechanics of the knee and prosthesis design’,J. Bone Joint. Surg. (Br),60, pp. 358–369
Katcherian, D. A. (1998): ‘Treatment of ankle arthrosis’,Clin. Orthop. Rel. Res.,349, pp. 48–57
Kitaoka, H. B., andPatzer, G. L. (1996): ‘Clinical results of the Mayo total ankle arthroplasty’,J. Bone Joint Surg. (Am),78, pp. 1658–1664
Kempson, G. E., Freeman, M. A. R., andTuke, M. A. (1975): ‘Engineering considerations in the design of an ankle joint’,J. Biomed. Eng.,10, pp. 166–180
Kofoed, H. A. (1986): ‘A new total ankle joint prosthesis’, inKossowky, R., andKossowsky, N. (Eds): ‘Material sciences and implant orthopaedic surgery’ (Martinus Nijhoff, Dordrecht, 1986), pp. 75–84
Lachiewicz, P. F. (1994): ‘Total ankle arthroplasty: indications, techniques, and results’,Orthopaed. Rev.,23, pp. 315–320
Leardini, A., O'Connor, J. J., Catani, F., Martelli, S., andGiannini, S. (1998): ‘The kinematics of the ankle in the sagittal plane’,J. Biomech.,31, Suppl. 1, pp. 10
Leardini, A., O'Connor, J. J., Catani, F., andGiannini, S. (1999a): ‘Kinematics of the human ankle complex in passive flexion — a single degree of freedom system’,J. Biomech.,32, pp. 111–118
Leardini, A., O'Connor, J. J., Catani, F., andGiannini, S. (1999b): ‘A geometric model of the human ankle joint’,J. Biomech.,32, pp. 585–591
Leardini, A., O'Connor, J. J., Catani, F., andGiannini, S. (2000): ‘The role of the passive structures in the mobility and stability of the human ankle joint: a literature review’,Foot Ankle Int.,21, pp. 602–615
Leardini, A., Catani, F., Giannini, S., andO'Connor, J. J. (2001a): ‘Computer-assisted design of the sagittal shapes for a novel total ankle replacement’,Med. Biol. Eng. Comput.,39, pp. 168–175
Leardini, A., Stagni, R., andO'Connor, J. J. (2001b): ‘Mobility of the subtalar joint in the intact ankle complex’,J. Biomech.,34, pp. 805–809
Pyevich, M. T., Saltzman, C. L., Callaghan, J. J., andAlvine, F. G. (1998): ‘Total ankle arthroplasty: a unique design. Two to twelve-year follow-up’,J. Bone Joint Surg. (Am),80, pp. 1410–1420
Rush, J. (1996): ‘Management of the rheumatoid ankle and hindfoot’,Current Orthopaed.,10, pp. 174–178
Van Deursen, D. L., Lengsfeld, M., Snijders, C. J., Evers, J. J., andGoossens, R. H. (2000): ‘Mechanical effects of continuous passive motion on the lumbar spine in seating’,J. Biomech.,33, pp. 695–699
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Leardini, A., Moschella, D. Dynamic simulation of the natural and replaced human ankle joint. Med Bio Eng Comput 40, 193–199 (2002). https://doi.org/10.1007/BF02348124
Received:
Accepted:
Issue Date:
DOI: https://doi.org/10.1007/BF02348124