Summary
A transverse surface crack is known to add to the shaft a local flexibility due to the stress-strain singularity in the vicinity of the crack tip. This flexibility can be represented by way of a 6 × 6 matrix describing the local flexibility in a short shaft element which includes the crack. This matrix has off-diagonal terms which cause coupling of motion along the directions which are indicated by the off-diagonal terms. Not all motions are coupled, however. To study the coupling of torsion and shear, a 3 × 3 flexibility matrix is used which includes the appropriate terms. Due to the shear terms of the Timoshenko beam equation of the shaft, bending vibration is finally coupled to torsional vibration. This effect is the subject of this investigation, which is of particular importance in turbomachinery operation. The equations of motion of a Timoshenko beam shaft with three degrees of freedom are derived. The free vibration of the shaft and the influence of the crack on the vibrational behaviour of the shaft is studied. The relation of the eigenvalues of the system, to the crack depth and the slenderness ratio of the shaft is derived. Moreover forced vibration analysis of the cracked shaft is performed. The significant influence of the bending vibration on the torsional vibration spectrum, and vice-versa, is demonstrated. It is believed that this effect can be very useful for rotor crack identification in service, which is of importance to turbomachinery.
Übersicht
Bekanntlich verringert ein von der Oberfläche in den Querschnitt reichender Riß infolge der Spannungs- und Verzerrungssingularität an der Rißspitze örtlich die Steifigkeit einer Welle. Dies kann mit Hilfe einer 6 × 6-Nachgiebigkeitsmatrix für ein kurzes Wellenstück, das den Riß enthält, beschrieben werden. Die Matrix enthält Elemente außerhalb der Diagonalen, wodurch eine Kopplung der Bewegungen in die Richtungen erfolgt, welche das Element anzeigt. Nicht alle Bewegungen sind dabei verknüpft. Zur Untersuchung der Kopplung von Torsion und Querschub wird eine 3 × 3-Nachgiebigkeitsmatrix benutzt, die die betreffenden Elemente enthält. Infolge der Querkraft-Terme in der Timoshenko-Balkengleichung werden letztendlich Biegef- und Torsionsschwingungen gekoppelt. Dieser Effekt ist Gegenstand der Untersuchung. Die Bewegungsgleichungen eines Timoshenko-Balkens mit 3 Freiheitsgraden werden hergeleitet. Die freien Schwingungen der Welle und der Einfluß des Risses auf das Schwingungsverhalten werden untersucht. Die Beziehungen zwischen Eigenformen, Rißtiefe und Schlankheitsgrad der Welle werden hergeleitet. Darüber hinaus werden erzwungene Schwingungen der angerissenen Welle untersucht. Der deutliche Einfluß der Biegeschwingung auf das Spektrum der Torsionsschwingung und umgekehrt wird aufgezeigt. Dieser Effekt ist bei Turbomaschinen bedeutsam, da er für die Identifizierung von Rotorrissen beim Betrieb nützlich sein müßte.
Similar content being viewed by others
References
Grabowski, B.; Mahrenholtz, O.: Theoretical and experimental investigations of shaft vibrations in turbomachinery excited by cracks. IFToMM Conference on Rotordynamics Problems in Power Plants, Roma, 1982, pp. 507–514
Nillson, L. R. K.: On the vibration behaviour of a cracked rotor. IFToMM Conf. Roma 1982, pp. 515 -524
Schmied, J.; Kramer, E.: Vibrational behaviour of a rotor with cross sectional crack. IMechE 1984, C279/84, pp. 183–192
Bachschmied, N.; Diana, G.: The Influence of unbalance on cracked rotors. IMechE 1984, C304/84, pp. 193–198
Papadopoulos, C. A.; Dimarogonas, A. D.: Coupled longitudinal and bending vibrations of a cracked rotating shaft. J. Sound Vibr. (to appear)
Dimarogonas, A. D.; Papadopoulos, C. A.: Vibration of cracked shafts in bending. J. Sound Vibr. 91 (1983) 583–593
Mayes, I. W.; Davies, W. G. R.: Analysis of the response of a multi rotor-bearing system containing a transverse crack in a rotor. Design and Production Engineering Technical Conference, Dearborn, Mich. ASME 83-DET-84, Sept. 1983
Inagaki, T.; Kanki, H.; Shiraki, K.: Transverse vibrations of a general cracked-rotor bearing system. ASME Paper 81-DET-45, Design Engineering Technical Conference, Sept. 1981
Dimarogonas, A. D.; Paipetis, S. A.: Analytical methods in rotor dynamics. London: Applied Science Pub. 1983
Tada, H.: The stress analysis of cracks handbook. Hellertown/PA: Del. Research Corp. 1973
Meirovitch, L.: Analytical methods in vibrations. London: Macmillan 1967
Dym, C. L.; Shames, I. H.: Solid mechanics. New York: McGraw Hill 1973
Timoshenko, S.: Vibration problems in engineering, 4th ed. Wiley 1974
Dimarogonas, A. D.: Vibration engineering. St. Paul: West Publishers 1976
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Papadopoulos, C.A., Dimarogonas, A.D. Coupling of bending and torsional vibration of a cracked Timoshenko shaft. Ing. arch 57, 257–266 (1987). https://doi.org/10.1007/BF00534404
Received:
Issue Date:
DOI: https://doi.org/10.1007/BF00534404