Fluid and enthalpy production during regional metamorphism

Abstract

Models for regional metamorphism have been constructed to determine the thermal effects of reaction enthalpy and the amount of fluid generated by dehydration metamorphism. The model continental crust contains an average of 2.9 wt % water and dehydrates by a series of reactions between temperatures of 300 and 750° C. Large scale metamorphism is induced by instantaneous collision belt thickening events which double the crustal thickness to 70 km. After a 20 Ma time lag, erosion due to isostatic rebound restores the crust to its original thickness in 100 Ma. At crustal depths greater than 10 km, where most metamorphism takes place, fluid pressure is unlikely to deviate significantly from lithostatic pressure. This implies that lower crustal porosity can only be maintained if rock pores are filled by fluid. Therefore, porosities are primarily dependent on the rate of metamorphic fluid production or consumption and the crustal permeability. In the models, permeability is taken as a function of porosity; this permits estimation of both fluid fluxes and porosities during metamorphism. Metamorphic activity, as measured by net reaction enthalpy, can be categorized as endothermic or exothermic depending on whether prograde dehydration or retrograde hydration reactions predominate. The endothermic stage begins almost immediately after thickening, peaks at about 20 Ma, and ends after 40 to 55 Ma. During this period the maximum and average heat consumption by reactions are on the order 11.2·10⁻¹⁴ W/cm³ and 5.9·10⁻¹⁴ W/ cm³, respectively. The maximum rates of prograde isograd advance decrease from 2.4·10⁻⁸ cm/s, for low grade reactions at 7 Ma, to 7·10⁻¹⁰ cm/s, for the highest grade reaction between 45 and 58 Ma. Endothermic cooling reduces the temperature variation in the metamorphic models by less than 7% (40 K); in comparison, the retrograde exothermic heating effect is negligible. Dehydration reactions are generally poor thermal buffers, but under certain conditions reactions may control temperature over depth and time intervals on the order of 1 km and 3 Ma. The model metamorphic events reduce the hydrate water content of the crust to values between 1.0 and 0.4 wt % and produce anhydrous lower crustal granulites up to 15 km in thickness. In the first 60 Ma of metamorphism, steady state fluid fluxes in the rocks overlying prograde reaction fronts are on the order of 5·10⁻¹¹ g/cm²-s. These fluid fluxes can be accommodated by low porosities (<0.6%) and are thus essentially determined by the rate of devolitalization. The quantity of fluid which passes through the metamorphic column varies from 25000 g/cm², within 10 km of the base of the crust, to amounts as large as 240000 g/cm², in rocks initially at a depth of 30 km. Measured petrologic volumetric fluid-rock ratios generated by this fluid could be as high as 500 in a 1 m thick horizontal layer, but would decrease in inverse proportion of the thickness of the rock layer. Fluid advection causes local heating at rates of about 5.9·10⁻¹⁴ W/cm³ during prograde metamorphism and does not result in significant heating. The amount of silica which can be transported by the fluids is very sensitive to both the absolute temperature and the change in the geothermal gradient with depth. However, even under optimal conditions, the amount of silica precipitated by metamorphic fluids is small (<0.1 vol %) and inadequate to explain the quartz veining observed in nature. These results are based on equilibrium models for fluid and heat transport that exclude the possibility of convective fluid recirculation. Such a model is likely to apply at depths greater than 10 km; therefore, it is concluded that large scale heat and silica transport by fluids is not extensive in the lower crust, despite large time-integrated fluid fluxes.