Abstract
A hybrid specimen was developed to minimize material used when assessing bending fatigue behavior with a vibration-based experimental procedure. Motivation for this work comes from the eagerness to quantify critical three-dimensionally printed gas turbine engine components at low cost under representative operating and stress conditions. The original vibration-based fatigue specimen (a whole, square plate) is capable of providing airfoil representative data at a lower cost than failing a fully manufactured airfoil. The reduced cost, though significant, was further reduced with the hybrid specimen. The most recently published iteration of the hybrid specimen produced an insert-plate system that required 95 % less material than the original specimen in order to gather fatigue data, and the hybrid specimen data compared favorably within a 95 % prediction interval of the original for Aluminum 6061-T6. Despite the successful comparison, improvements to the hybrid plate specimen were still necessary for accurately assessing fatigue behavior of more commonly used aerospace alloys. Specifically, improving repeatability in the experimental response, increasing the hybrid specimen excitability (i.e. reduce specimen system damping), and minimizing damage accumulation on the carrier plate of the hybrid specimen were critical to the efficiency of the characterized bending fatigue behavior. The proposed investigation addressed these issues for Titanium 6Al-4V, resulting in a more repeatable experimental procedure and results that agree with whole plate data.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
Abbreviations
- A :
-
Stress-life regression parameter
- B :
-
Stress-life regression intercept
- g :
-
Gravitational constant (9.81 m/s2)
- N fail :
-
Number of cycles to failure
- N step :
-
Number of cycles per step
- με a :
-
Microstrain amplitude
- σ a :
-
Stress amplitude
- σ fail :
-
Stress amplitude during failed step
- σ pr :
-
Stress amplitude during previous step
References
Department of Defense Handbook: Engine Structural Integrity Program (ENSIP), MIL HDBK-1783B (USAF), 15 Feb 2002
American Society for Testing and Materials: E466-07: standard practice for conducting force controlled constant amplitude axial fatigue tests of metallic materials. In: ASTM Book of Standards, vol. 03.01. ASTM International, West Conshohocken, PA (2009)
Scott-Emuakpor, O., Shen, M.-H.H., George, T., Cross, C., Calcaterra, J.: Development of an improved high cycle fatigue criterion. ASME J. Eng. Gas Turbines Power 129(1), 162–169 (2007)
George, T., Seidt, J., Shen, M.-H.H., Cross, C., Nicholas, T.: Development of a novel vibration-based fatigue testing methodology. Int. J. Fatigue 26, 477–486 (2004)
George, T., Shen, M.-H.H., Cross, C., Nicholas, T.: A new multiaxial fatigue testing method for variable amplitude loading and stress ratio. ASME J. Eng. Gas Turbines Power 128, 857–864 (2006)
George, T., Shen, M.-H.H., Scott-Emuakpor, O., Nicholas, T., Cross, C., Calcaterra, J.: Goodman diagram via vibration-based fatigue testing. ASME J. Eng. Mater. Technol. 127(1), 58–64 (2005)
Scott-Emuakpor, O., Schwartz, J., George, T., Holycross, C., Cross, C., Slater, J.: Bending fatigue life characterization of direct metal laser sintering nickel alloy 718. Fatigue Fract. Eng. Mater. Struct. 38(9), 1105–1117 (2015)
Scott-Emuakpor, O., Holycross, C., George, T., Knapp, K., Beck, J.: Fatigue and strength studies of titanium 6Al-4V fabricated by direct metal laser sintering. ASME J. Eng. Gas Turbines Power 138(2) (2015), paper No. GTP-15-1306
Bruns, J., Zearley, A., George, T., Scott-Emuakpor, O., Holycross, C.: Vibration-based bending fatigue of a hybrid insert-plate system. J. Exp. Mech. 55(6), 1067–1080 (2015)
Simons, D., Leissa, A.: Vibrations of rectangular cantilever plates to in-plane acceleration loads. J. Sound Vib. 17(3), 407–422 (1971)
Meirovitch, L.: Principles and Techniques of Vibrations. Prentice Hall, New Jersey (1997)
Mower, T.: Degradation of titanium 6Al-4V fatigue strength due to electrical discharge machining. Int. J. Fatigue 64, 84–96 (2014)
Blackwell, C., Palazotto, A., George, T., Cross, C.: The evaluation of the damping characteristics of a hard coating on titanium. Shock. Vib. 14, 37–51 (2007)
Scott-Emuakpor, O., Shen, M.-H.H., George, T., Cross, C.: A energy-based uniaxial fatigue life prediction method for commonly used gas turbine engine materials. ASME J. Eng. Gas Turbines Power 130(6) (2008), paper No. 062504
Bruns, J.: Fatigue crack growth behavior of structures subject to vibratory stresses. In: Society of Experimental Mechanics Annual Conference, International Student Paper Competition, Greenville, SC, 2–6 June (2014)
Maxwell, D.C., Nicholas, T., A rapid method for generation of a Haigh diagram for high cycle fatigue. J. Fatigue Fract. Mech., ASTM STP 1321, 29, 626–641 (1998)
Nicholas, T.: High Cycle Fatigue: A Mechanics of Materials Perspective. Elsevier, Oxford (2006)
Scott-Emuakpor, O., Holycross, C., George, T., Beck, J., Schwartz, J., Shen, M.-H.H., Slater, J.: Material property determination of vibration fatigued DMLS and cold-rolled nickel alloys. ASME/Turbo Expo, Dusseldorf, Germany, 16–20 June 2014, Paper No. GT2014-26247
Bellows, R., Muju, S., Nicholas, T.: Validation of the step test method for generating Haigh diagrams for Ti-6Al-4V. Int. J. Fatigue 21(7), 687–697 (1999)
Scott-Emuakpor, O., George, T., Cross, C., Wertz, J., Shen, M.-H.H.: A new distortion energy-based equivalent stress for multiaxial fatigue life prediction. Int. J. Non Linear Mech. 47(3), 29–37 (2012)
American Society for Testing and Materials: E 8M-09: standard test methods for tension testing of metallic materials. In: ASTM Book of Standards, vol. 03.01. ASTM International, West Conshohocken (2009)
Prevey, P., Jayaraman, N., Ravindranath, R.: Introduction of residual stress to enhance fatigue performance in the initial design. ASME/Turbo Expo, Vienna, Austria, 14–17 June 2004, Paper No. GT2004-53971
American Society for Testing and Materials: E739-10: standard practice for statistical analysis of linear or linearized stress-life (S-N) and strain-life (ε-N) fatigue data. In: ASTM Book of Standards, vol. 03.01. ASTM International, West Conshohocken (2009)
Kutner, M., Nachtsheim, C., Neter, J.: Applied Linear Regression Models. McGraw-Hill/Irwin, New York (2004)
Acknowledgements
The authors would like to thank the following organizations for funding and collaboration: the Turbine Engine Fatigue Facility (TEFF) of the United States Air Force Research Laboratory (AFRL) and Universal Technology Corporation (UTC). Specifically, the authors would like to acknowledge UTC contractors Phil Johnson, Jeff Bruns, and Alyssa Zearley for their contribution to specimen and fixture design and analysis, as well as laboratory testing and experimentation setup.
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2017 The Society for Experimental Mechanics, Inc.
About this paper
Cite this paper
Scott-Emuakpor, O., George, T., Holycross, C., Cross, C. (2017). Improved Hybrid Specimen for Vibration Bending Fatigue. In: Zehnder, A., et al. Fracture, Fatigue, Failure and Damage Evolution, Volume 8. Conference Proceedings of the Society for Experimental Mechanics Series. Springer, Cham. https://doi.org/10.1007/978-3-319-42195-7_4
Download citation
DOI: https://doi.org/10.1007/978-3-319-42195-7_4
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-319-42194-0
Online ISBN: 978-3-319-42195-7
eBook Packages: EngineeringEngineering (R0)