High performance photocatalyst TiO2@UiO-66 applied to degradation of methyl orange

MOFs have considerable adsorption capacity due to their huge specific surface area. They have the characteristics of photocatalysts for their organic ligands can absorb photons and produce electrons. In this paper, the photodegradation properties of TiO2 composites loaded with UiO-66 were investigated for the first time for MO. A series of TiO2@UiO-66 composites with different contents of TiO2 were prepared by a solvothermal method. The photocatalytic degradation of methyl orange (MO) was performed using a high-pressure mercury lamp as the UV light source. The effects of TiO2 loading, catalyst dosage, pH value, and MO concentration were investigated. The results showed that the degradation of MO by TiO2@UiO-66 could reach 97.59% with the addition of only a small amount of TiO2 (5 wt%). TiO2@UiO-66 exhibited significantly enhanced photoelectron transfer capability and inhibited efficient electron–hole recombination compared to pure TiO2 in MO degradation. The composite catalyst indicated good stability and reusability when they were recycled three times, and the photocatalytic reaction efficiencies were 92.54%, 88.76%, and 86.90%. The results provide a new option to design stable, high-efficiency MOF-based photocatalysts. Supplementary Information The online version contains supplementary material available at 10.1186/s11671-023-03894-6.


Introduction
With the rapid development of industry, human activities have caused a lot of environmental pollution [1].Among the environment wastewater, toxic organic pollutants have serious impacts on ecosystems and human health.Thus, many researchers have made great efforts to develop efficient treatment technologies to remove pollutants in water [2].Conventional methods for the removal of organic pollutants include adsorption [3], precipitation [4], membrane separation, and biological treatments [5].Among various physical and chemical pollutant removal methods, photocatalytic degradation of organic pollutants has been proved to be a simple, cost-effective, and environmentally-friendly method [6,7].The photocatalysis is the redox reaction of the semiconductor material with the reactant under the irradiation of light.Researchers have found that a variety of semiconductor materials such as TiO 2 , Fe 2 O 3 , WO 3 , CdS, Bi 2 WO 6 , BiOCl, g-C 3 N 4 , and MOFs can be used for the degradation of organic pollutants, hydrogen production from water decomposition, organic synthesis, and heavy metal ion reduction [8][9][10][11][12][13]. 1 3 Metal-organic frameworks (MOFs) have attracted great interest from researchers all over the world due to their unique, outstanding properties, and potential applications [14,15].Among various MOFs, Zr-based MOFs (UiO-66) have gained crucial interest in photoinduced water treatment due to their construction of Zr 6 O 4 (OH) 4 clusters and organic linkers [14].UiO-66 has high thermal stability, superior chemical resistance to a variety of solvents, excellent chemical stability under a variety of conditions, and excellent corrosion resistance to high external pressure.Theoretical studies show that when UiO-66 is exposed to light, the organic ligands are excited to generate electrons, and then the electrons are transferred to the metal centers through valence bonds, that is, the ligand-metal charge transfer occurs, which effectively increases the lifetime of photogenerated carriers [16][17][18].UiO-66 can be directly used as a photocatalyst or subjected to various modifications.The common photocatalytic modifications of UiO-66 include the preparation of UiO-66 with defects, the preparation of functionalized UiO-66-NH 2 , the incorporation of other metal ions other than Zr, the modification of materials with specific properties after synthesis, and the formation of composite materials after mixing with other substances.Among them, the last modification is often used because of its simply preparation method.The hybrid nanoparticles, such as magnetic nanoparticles, alumina, silica, graphene oxide (GO), carbon nanotubes (CNTs), polymers and amorphous carbon and other suitable materials has received much attention [14].Combining UiO-66 nanoparticles with these nanoparticles can improve the physicochemical properties, external morphology, adsorption kinetics, and stability of MOF.This approach has two advantages applied in photocatalysis: (i) the combined coverage of the light absorption edge and visible region is expanded compared to UiO-66 or its amino-functionalized derivative (UiO-66-NH 2 ), resulting in a narrower band gap of the photocatalyst; (ii) improved separation efficiency of photogenerated electron-hole pairs due to electron transfer between UiO-66 and semiconductor.TiO 2 photocatalysts have been widely concerned by researchers due to their low price, good chemical stability, and high photocatalytic efficiency [19][20][21].However, their performance is hindered by poor adsorption properties and rapid recombination of photogenerated carriers.To alleviate these problems, many efforts have been made, such as morphological design [22], elemental doping [23], and heterojunction engineering [24].It is recognized that an effective combination of multiple strategies will maximize the efficiency of photocatalysts.
The degradation of anionic organic dyes MO by pure UiO-66 has been studied [33][34][35][36], while the degradation of cationic dyes, such as RhB, by UiO-66-NH 2 , has also been studied [31,37].Also there have been studies on the degradation of MO by α-Fe 2 O 3 , CdS, In 2 S 3 mixed with UiO-66 or UiO-66-NH 2 .In contrast, the degradation of MO by TiO 2 compound UiO-66 has not been studied, it is necessary to study TiO 2 @UiO-66 as a catalyst to determine the effect of TiO 2 addition on the degradation of MO by UiO-66 for anionic organic dyes.
Here, TiO 2 @UiO-66 was successfully prepared by a simple solvothermal method (Fig. 1).The photocatalytic activity of MO was evaluated by UV-light degradation.TiO 2 @UiO-66 exhibits stronger photocatalytic activity than TiO 2 and UiO-66 under UV light.In addition, the composite catalyst also showed good stability and reusability.

Materials characterization
Powder X-ray diffraction (XRD) patterns were determined on a SmartLab (Ultima IV, Rigaku Corporation, Japan) with Cu-Ka radiation and a scan rate of 10°•min −1 between 5 • and 80 • .Thermogravimetric Analysis (TGA) data was obtained from 25 to 800 °C by a Linseis STA PT 1600 ((Linseis Messgeräte GmbH, Germany).The morphology of the photocatalysts was measured by transmission electron microscope (TEM, Tecnai F30) and scanning electron microscope (SEM, Apreo S).The Fourier-transform infrared (FT-IR) spectra of the photocatalysts was recorded using a NEXUS 670 in the wavelength range of 400-4000 cm −1 .Specific surface area, pore size distribution and pore volume of all samples tested were determined using a Micromeritics ASAP2020 apparatus.And the surface area was calculated using the Brunauer-Emmett-Teller technique, whilst the pore size distribution was measured from the nitrogen isotherms using Barrett-Joyner-Halenda (BJH) method and the Horvath-Kawazoe method, respectively.The UV-Vis diffuse reflectance spectra of the samples were collected with a UV-Vis spectrometer (Lambda 950 + Refle, spectral range 250-800 nm).The photoluminescence spectra (PL) were surveyed on an FLS920 spectrophotometer.Electrochemical impedance testing using an electrochemical workstation (CHI 660E made by Chenhua, Shanghai, with Pt as counter electrode and Ag/AgCl electrode as reference electrode).The generated radicals under 250 W high-pressure mercury lamp illumination were measured with the electron spin resonance (ESR) spectrometer (Bruker A300-10/12).

Measurement of photocatalytic activities
100 mL MO solution (15 mg•L −1 ) was mixed with a certain amount of catalyst before UV irradiation, the suspension was stirred for 60 min in the dark to reach adsorption-desorption equilibrium.After that, the suspensions were irradiated by UV light from a 250 W high-pressure mercury lamp. 2 mL of the suspension was sampled every 30 min.The suspension was centrifuged to remove the solid catalyst, then define the degradation rate: X% = (1− C t /C 0 ) × 100%, where C 0 was the initial concentration of solution and Ct was the solution concentration for each period.

Results and discussion
Characterization SEM of the surface morphology of UiO-66 and TiO 2 @UiO-66 is presented in Fig. 2A-F.It can be seen that the as-synthesized pristine UiO-66 exhibits a smooth, regular, and uniform octahedral appearance with a size of about 300 nm, the same as the shapes obtained by solvothermal reactions in other literature [39,40].Compared with UiO-66, the size and morphology of TiO 2 @UiO-66 composite did not change significantly.The difference is that uniformly distributed TiO 2 nanoparticles are found on the surface of TiO 2 @UiO-66.From the above observations, it can be inferred that adding TiO 2 to the Fig. 2 The morphological characteristics of TiO 2 @UiO-66.A-C SEM images of UiO-66; B-F SEM images of TiO 2 @UiO-66( 5); (G-I) TEM images of TiO 2 @UiO-66 (5) and Elemental mapping images of O, Ti, Zr elements in TiO 2 @UiO-66 (5) in last line precursor solution of UiO-66 does not affect the growth of UiO-66.TEM images of TiO 2 @UiO-66 are shown in Fig. 2G-I.It can be observed that TiO 2 @UiO-66 composite has a regular octahedral shape, and its surface is evenly distributed with TiO 2 nanoparticles, which can effectively alleviate the agglomeration of TiO 2 during the reaction process and increase the point of the active site, and can promote the separation of carriers.According to the results of the Mapping maps, we can see that Ti, O, and Zr elements are uniformly distributed in TiO 2 @UiO-66.
The asymmetric stretching vibrations at 663 and 507 cm −1 are attributed to the µ 3 -O and µ 3 -OH stretching vibrations.Compared with pristine UiO-66, TiO 2 @UiO-66 show a significant decrease in the relative intensity of the characteristic peaks of UiO-66 could be observed, which could be attributed to the strong interaction between TiO 2 and UiO-66 [21].
Figure 3C shows the TG analysis of UiO-66, TiO 2 @UiO-66(5), and TiO 2 .UiO-66 and TiO 2 @UiO-66 (5) show similar weight loss processes.The weight loss at 50-150 °C in the first stage is mainly due to the evaporation of water on the surface of the material.The weight loss in the second stage in the range of 200-400 °C is due to the evaporation of DMF in the pores of UiO-66.The weight loss in the third stage in the range of 450-600 °C is mainly due to the decomposition of BDA [28].Therefore UiO-66 has high thermal stability, which is consistent with previous reports [40].It should be noted that the thermal stability of the TiO 2 @UiO-66 composite is higher than that of the pristine UiO-66.It is not difficult to see from the TG results that UiO-66, TiO 2 @UiO-66, and TiO 2 exhibit relatively high thermal stability.
The spectra of UV-visible light absorption (Fig. 4A) were obtained to be evaluated light-absorption ability.The UV light region absorption intensity of TiO 2 @UiO-66( 5) is much higher than other samples.This is expected to improve the photocatalytic performance of TiO 2 @UiO-66 composite for MO degradation.
To determine the band energy diagram of the TiO 2 @UiO-66 heterojunction, the valence band (VB) maximum and band gap energy (Eg) of pure TiO 2 and UiO-66 have been investigated.Figure 4B presents the plot between (αhν) 2 and photon energy for band gap determination.According to the Kubelka-Munke equation, the Eg of these samples can be obtained [49] .TiO 2 , UiO-66 and TiO 2 @UiO-66( 5) have the Eg of 3.00, 3.41 and 2.90 eV, respectively.The lowering of the band gap is used to improve the macroscopical solar energy utilization of MOF-based photocatalysts.Thus, the decrease in Eg for the TiO 2 @UiO-66(5) heterostructure could be advantageous for the enhanced photocatalytic performance by increasing light-harvesting efficiency, theoretically.
Figure 4C reveals the photoluminescence spectrum of TiO 2 , UiO-66, and TiO 2 @UiO-66 samples under 300 nm excitation wavelength.When compared with TiO 2 , the PL intensity of TiO 2 @UiO-66 declined.The lower recombination rate of photogenerated charge careers led to the reduction of PL intensity, suggesting that the TiO 2 @UiO-66(5) exhibits a better property to the separation of electron-hole pair [50].The separation and transport efficiency of photogenerated carriers are the decisive factors affecting the photocatalytic process.EIS patterns (Fig. 4D) show that the as-prepared materials are arranged in the following order: UiO-66 > TiO 2 > TiO 2 @UiO-66 (5), which means that the recombination of UiO-66 with TiO 2 nanoparticles will facilitate electron transfer [51].
The specific surface area and pore size distribution of UiO-66 and TiO 2 @UiO-66 composites were determined by the N 2 adsorption method.Figure S1 show that the adsorption-desorption isotherms of both materials are type I isotherms, and the TiO 2 @UiO-66 composite and UiO-66 are typical microporous materials.The calculated BET surface area and pore size of UiO-66 and TiO 2 @UiO-66 are shown in Table S1.The BET surface areas of UiO-66 and TiO 2 @UiO-66(5) are 775.12m 2 •g −1 and 685.94 m 2 •g −1 , respectively, and the pore sizes are 2.45 nm and 1.98 nm, respectively.According to the results in Table S1, it can be concluded that when UiO-66 is compounded with TiO 2 , the specific surface area, and Fig. 4 The optical characterization of TiO 2 @UiO-66.A UV-vis spectroscopy for the composite materials; B The converted Tauc plot of (αhν) 2  versus photo energy; C The PL spectra of the composite materials; D The EIS spectra of TiO 2 , UiO-66 and TiO 2 @UiO-66(5) composite materials pore size decrease, indicating that the introduction of TiO 2 blocks part of the pores of UiO-66, but still has a large specific surface area.

Effects of TiO 2 loading
Figure 5A shows the effect of TiO 2 contents to MO degradation when the photocatalyst dosage is 0.2 g•L −1 , the concentration of MO is 15 mg•L −1 and pH = 2. TiO 2 @UiO-66 composites with different contents of TiO 2 were prepared with loadings of 1, 3, 5, and 7%, respectively.In Fig. 5A, the adsorption effect of TiO 2 on MO is very low in the dark reaction stage, while the adsorption ability of UiO-66 on MO is very strong.In the photocatalytic stage, the catalytic capacity of TiO 2 is much greater than UiO-66(according to the slope of the lines).The effect of adsorption and degradation efficiency of pure TiO 2 is 56.98% and UiO-66 is 61.58% within 150 min under UV light.In the absence of catalyst, less than 5% of MO was degradation after 150 min.From Fig. 5A, it is quite clear that the degradation efficiency of TiO 2 @UiO-66(x) to MO can reach over 92%, much higher than pure UiO-66 and TiO 2 .The addition of micro-TiO 2 can greatly improve the degradation efficiency of MO.The sorption of the composites to MO is bigger than that of UiO-66 and TiO 2 in the dark reaction stage and the degradation efficiency of composites is higher than that of UiO-66 and TiO 2 in the photocatalytic stage.MO adsorbed on TiO 2 @UiO-66(x) is easy to be degraded because of its close proximity.
The photocatalytic degradation of MO can be analyzed by a quasi-first-order reaction, and their fitting diagram is shown in Fig. 5B.Table S2 lists the kinetic rate of TiO 2 @UiO-66 composite.It can be seen that the kinetic rate of TiO 2 @UiO-66( 5) is the highest, which is 0.01438 min −1 .TiO 2 @UiO-66(5) with a loading of 5% was used in subsequent experiments.

Effects of pH
Figure 5C show the effect of pH on MO degradation when the photocatalyst dosage is 0.2 g•L −1 and the concentration of MO is 15 mg•L −1 .It is clear that the TiO 2 @UiO-66(5) composite exhibits excellent photocatalytic activity at pH = 2, with a degradation efficiency of 97.59%.After dark adsorption for 60 min, the adsorption capacities of the solution at pH range 2-8 were 43.04, 47.78, 54.48, 37.76 and 37.63%, respectively.Zeta potential (Fig. S2) shows that the surface charge of the catalyst decreases with increasing pH in the pH range of 2-8, so that TiO 2 @UiO-66(5) composites are more sensitive to the anionic dye MO at low pH.In addition, H + is easily adsorbed on the surface of TiO 2 at low pH, which makes the TiO 2 particles positively charged [52,53].The positively charged TiO 2 particles facilitate the transfer of photoinduced electrons, which react with adsorbed O 2 to generate [29].The positively charged TiO 2 particles can also inhibit the recombination of electrons and holes, and generate more •OH through the reaction of holes with water, thereby enhancing the photocatalytic efficiency [54,55].

Effects of initial concentrations
Figure 5D shows the effects of MO concentration on degradation when the photocatalyst dosage is 0.2 g•L −1 and pH = 2.It can be seen that the degradation efficiency of MO depends on its initial concentration, and the photodegradation efficiency reaches to 79.40% when the dye concentration is 20 mg•L −1 .The increase in the concentration of MO leads to an increase in the amount of dye adsorbed on the catalyst surface, which promotes the enhancement of the degradation efficiency and the amount of the total degradation amount.

Effects of photocatalyst dosage
Figure 5E shows the effect of photocatalyst dosage on MO degradation when the concentration of MO is 15 mg•L −1 and pH = 2.When the catalyst concentration was 0.2 g•L −1 , it had the highest degradation efficiency.This can be thought that the increase in the number of photogenerated carriers and the total active surface area with the increase of catalyst dosage, thus the photocatalytic efficiency increases.When the catalyst is added too much, the turbidity of the suspension increases, and the penetration of light decreases, resulting in a decrease in the utilization rate of light.According to previous research reports, the photocatalytic degradation of other organic pollutants also showed a dependence on catalyst dosage [51,56,57].
Figure 5F shows the UV-Vis absorption spectra of MO after photocatalytic degradation at a catalyst concentration of 0.2 g•L −1 , MO concentration at 15 mg•L −1 , and pH = 2.The characteristic absorption peak intensity of MO at 504 nm decreased significantly when the illumination time increased to 150 min.The results showed that MO was effectively degraded and no other substances were formed.
The photocatalytic activity of TiO 2 @UiO-66 (5) for MO is compared with the reported TiO 2 -based catalysts.The data in Table 1 show that the photocatalyst reported in this study is more effective for the photodegradation of MO compared to the catalysts already reported.

Cycling performance
To explore the recyclability of the material, TiO 2 @UiO-66(5) composite was used repeatedly three times.Figure S3A shows that the degradation efficiency of TiO 2 @UiO-66(5) composites to MO respectively were 92.54%, 88.76%, and 86.90% after three-cycle experiments.Obviously, the degradation efficiency did not decrease significantly with the increase of the number of cycles.Perhaps the pores of TiO 2 @UiO-66(5) are blocked to some extent when the adsorption of MO in each photocatalytic process and affect the photocatalytic effect.Figure S3B and S3C is the XRD pattern and SEM of TiO 2 @UiO-66(5) after three experiments.Before and after photocatalysis, the crystal structure and morphology of TiO 2 @UiO-66(5) did not change significantly, indicating that the material has good stability and recyclability.

Water stability and structural stability
The water stability and structural stability of TiO 2 @UiO-66 was evaluated by XRD after being exposed to liquid water for up to 15 days.Figure S4 shows that TiO 2 @UiO-66(5) can preserve the crystal structure perfectly throughout the whole water stability experiment because its XRD patterns remain nearly unchanged for up to 15 days.Our measurements show that the compound shows remarkable water stability and structural stability.
In addition, the TiO 2 @UiO-66(5) after degradation of MO was characterized by SEM and EDS to further investigate its properties.SEM images (Fig. S5) showed that after degradation of MO, TiO 2 @UiO-66(5) remained intact with its original morphology.The composite exhibits an octahedral shape with a large number of TiO 2 particles coated on the surface.Mapping and EDS (Fig. S5D and Fig. S6) observed that after degradation of MO, the characteristic element in MO, S, appeared on the surface of TiO 2 @UiO-66 (5).It indicates that MO indeed reacted on the surface of TiO 2 @UiO-66(5) to complete the degradation.

Mechanisms for MO photocatalytic degradation
From the VB-XPS spectra (Fig. 6A and B), the valence band (VB) values of TiO 2 and UiO-66 are 3.01 and 2.78 eV, respectively.Energy band theory tells us that we can calculate the values of the conduction band (CB) of TiO 2 and UiO-66 according to the formula CB = VB − Eg , which are 0.01 and − 0.63 eV, respectively.From this, the ΔE V and ΔE C offsets between UiO-66 and TiO 2 can be calculated to be 0.23 and 0.64 eV, respectively.
Both ΔEc and ΔEv are positive, so it comes out that TiO 2 @UiO-66 is a type-II heterojunction.Since the light intensity and the applied electric field strongly affect the properties of the type II heterojunction, it makes the type-II heterojunction exhibit unusual dynamics of the carriers compared to the type-I heterojunction, which can promote the efficient separation of the photogenerated charge carriers.
To explore the main active species in the degradation process, isopropanol (TBA), EDTA-2Na, and benzoquinone (BQ) at the same concentrations were used to quench OH radical, hole, and •O 2 − radical, respectively.In the presence of BQ, the effect of photocatalytic degradation of MO decreased significantly, indicating that •O 2 − plays a major role in photocatalytic processes (Fig. 6C).When TBA is added in the solution, the catalytic activity of TiO 2 @UiO-66( 5) is hardly different with that of without TBA.It can be considered that •OH is not the main active species of MO degradation.The amount of •O 2 − decreases with the electrons decrease when the holes are consumed by EDTA-2Na.Therefore, the catalytic efficiency of MO degradation decreases.In summary, TiO 2 @UiO-66 provides •O 2 − which reacts with organic matter to produce degradation products and water, while •OH is only an auxiliary catalytic group.
To further confirm that there is radical generation in the photocatalytic system, we used ESR spectroscopic technology.As shown in Fig. 6D and E, the characteristic signal of DMPO-•OH and DMPO-•O 2 -was not observed under dark conditions.After 5 min of irradiation with a high-pressure mercury lamp, we observed the characteristic signals of DMPO-•OH and DMPO-•O 2 -.The results showed that •OH-and •O 2 -radicals were indeed generated in this photocatalytic system, which is consistent with the previous experimental results.Based on the above discussion, we propose a possible mechanism for TiO 2 @UiO-66 photocatalytic degradation of MO(Fig.6F).According to the photodegradation principle, the ground state electrons on the VB can excite the CB after absorbing photons, making CB carry free electrons and leaving holes on the VB.The oxidation reaction occurs when the VB potential of the photocatalyst is higher than the redox potential of the •OH radical (E 0 (H 2 O/•OH) = 2.7 V vs. NHE).The reduction reaction occurs when the CB potential of the photocatalyst is lower than the redox potential of the •O 2 − radical (E 0 (O 2 /•O 2 − ) = -0.28V vs. NHE) [78].Holes on the VB are strong oxidants and electrons on CB are strong reducing agents.The holes react with H 2 O to produce chemically active free radical groups (•OH) (Eq.1), the combination of electrons on the CB and O 2 also produces chemically active free radical groups (•O 2 − ) (Eq. 2).•OH and•O 2 − radicals degrade with organic contaminants (Eqs.3,4).Under illumination, UiO-66 and TiO 2 in TiO 2 @UiO-66 composites can be excited by ultraviolet light, generating electrons and holes on CB and VB, respectively.Both potentials of UiO-66 and TiO 2 are higher than H 2 O/•OH (2.7 eV vs. NHE), so some of the h + generates •OH on the material surface combining with H 2 O.Meanwhile, the CB potential of UiO-66 is lower than O 2 /•O 2 − (-0.3 eV vs. NHE), so the e-on UiO-66 is easily trapped by oxygen generating •O 2 − (Fig. 6F) [79].Due to the tight combination of UiO-66 and TiO 2 , the electrons on the CB of TiO 2 are transferred to the CB of UiO-66.The quantity of •O 2 − produced by the composite catalyst is larger than that of the single catalyst.Based on the obtained results, the enhanced photoactivity of the composite is mainly attributed to a decrease in Eg and an improved electron-hole separation. (1)

Conclusions
The photocatalytic degradation of MO by TiO 2 loaded with UiO-66 was investigated for the first time.The composite MOFs catalyst, TiO 2 @UiO-66 was prepared by adding micro-TiO 2 by solvothermal method, and their photocatalytic performance was explored with MO as the target pollutant.In the study of influencing conditions, the effects of TiO 2 loading, solution pH, catalyst dosage, and initial solution concentration on the photocatalytic degradation were investigated.The photocatalytic activity of the TiO 2 @UiO-66 composite was higher than that of TiO 2 and UiO-66, and its degradation rate of MO could reach 97.59%.After three cycles, the degradation rate of MO still reaches 86.90%, showing excellent photocatalytic activity and good cycling performance.Its excellent photocatalytic performance can be attributed to two aspects: (1) The huge specific surface area of UiO-66 can significantly improve the adsorption effect of TiO 2 .(2) The close contact interface between TiO 2 and UiO-66 can effectively separate and transfer photogenerated carriers.The free radical trapping experiments show that •O 2 − is the active species that play a major role in the degradation.Moreover, TiO 2 @UiO-66 still has an intact structure after being immersed in aqueous solution for 15 days, and it has excellent water stability.The results demonstrated that TiO 2 @UiO-66 is a kind of catalyst with simple preparation, stable structure and good catalytic performance for the purification of environmental organic contaminants.

Fig. 5
Fig. 5 The photocatalytic performance of TiO 2 @UiO-66.A Photocatalytic degradation of MO with the composite materials; B The fitting curve by a quasi-first-order reaction; C The effect of initial pH; D MO concentration; E Dosage of catalyst; F The UV-VIS absorption spectra of MO after photocatalytic degradation Dye + •OH → H 2 O + dyeintermediates# (4) Dye + •O − 2 → H 2 O + dyeintermediates#

Table 1
Comparison