Skip to main content
SpringerLink
Log in

Numerical Analysis of a Radiant Heat Flux Calibration System

  • Published:
International Journal of Thermophysics Aims and scope Submit manuscript

Abstract

Heat flux gauges are one of the devices that are used to determine the heat loads to which high-speed aerospace structures are subjected during flight. Prior to installation, these gauges are calibrated. The calibration system must be well understood if the heat flux gauges are to provide useful data during flight tests. A pseudo three-dimensional model of the radiant heat flux gauge calibration system was developed. The radiant heat flux gauge calibration system consists of a graphite plate heater and a circular foil heat flux gauge. The numerical model simulates the combined convection, radiation, and mass loss by chemical reaction on the graphite plate surface. It can be used to identify errors due to heater element erosion, and the deviations in the predicted heat fluxes due to uncertainties in various physical parameters of the system. A fourth-order finite difference scheme is used to solve the steady-state governing equations and to determine the temperature distribution in the gauge and the graphite plate, the incident heat flux on the gauge face, and the flat plate erosion. Initial gauge heat flux predictions from the model are found to be within ±5% of experimental results.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

REFERENCES

  1. D. Holmberg, K. Steckler, C. Womeldorf, and W. Grosshandler, in Proceedings of the ASME International Mechanical Engineering Conference and Exhibition (ASME, New York, 1997), Vol. 3, p. 165.

    Google Scholar 

  2. W. L. Grosshandler and D. Blackburn, in Proceedings of the ASME International Mechanical Engineering Conference and Exhibition (ASME, New York, 1997), Vol. 3, p. 153.

    Google Scholar 

  3. A. V. Murthy, B. K. Tsai, and R. D. Saunders, in Proceedings of the ASME International Mechanical Engineering Conference and Exhibition (ASME, New York, 1997), Vol. 3, p. 159.

    Google Scholar 

  4. T. J. Horn, Comparison of Heat Flux Standard for Calibration Heat Flux Gage at Elevated Temperature and High Heat Flux Levels, Master's thesis (Virginia Polytechnic Institute and State University, Blacksburg, 1993).

  5. E. S. Cameron, SPIE 1044:155 (1989).

    Google Scholar 

  6. A. F. Mills, Basic Heat and Mass Transfer (Prentice-Hall, Upper Saddle River, NJ, 1999).

    Google Scholar 

  7. S. V. Patankar, Numerical Heat Transfer and Fluid Flow (Hemisphere, New York, 1984).

    Google Scholar 

Download references

Author information

Authors and Affiliations

  1. Department of Mechanical and Aerospace Engineering, University of California Los Angeles, Los Angeles, California, 90095, U.S.A.

    S. Jiang & V. K. Dhir

  2. Dryden Flight Research Center, National Aeronautics and Space Administration, Edwards, California, 93523, U.S.A.

    T. J. Horn

Authors
  1. S. Jiang
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. T. J. Horn
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. V. K. Dhir
    View author publications

    You can also search for this author in PubMed Google Scholar

Rights and permissions

Reprints and permissions

About this article

Cite this article

Jiang, S., Horn, T.J. & Dhir, V.K. Numerical Analysis of a Radiant Heat Flux Calibration System. International Journal of Thermophysics 21, 941–963 (2000). https://doi.org/10.1023/A:1006622526578

Download citation

  • Issue Date:

  • DOI: https://doi.org/10.1023/A:1006622526578

Search

Navigation