Abstract
This study reports the improvement of the mechanical properties of Al2O3 porous ceramics from particle-stabilized colloidal suspension with the addition of carbon fiber through direct foaming. The initial colloidal suspension of Al2O3 was partially hydrophobized by a surfactant, propyl gallate (2 wt%), to stabilize the wet foam used with the addition of carbon fiber from 2 to 8 wt% as reinforcement. The influence of carbon fiber on the air content, bubble size, pore size, and pore distribution were discussed in terms of the wet foam stability and the physical properties of the porous ceramics. The mechanical properties of the sintered porous samples were investigated by the Hertzian indentation test. The results show that the wet foam stability of more than 90% corresponds to the compressive load bearing capacity of 110 N using tungsten carbide ball with a radius of r = 7.93 mm and the elastic modulus of 114.3 MPa in the sintered sample with 2 wt% of carbon content.
Similar content being viewed by others
References
A.R. Studart, U.T. Gonzenbach, E. Tervoort, L.J. Gauckler, Processing routes to macroporous ceramics: a review. J. Am. Ceram. Soc. 89(6), 1771–1789 (2006)
T. Shimizua, K. Matsuura, H. Furuea, K. Matsuzaka, Thermal conductivity of high porosity alumina refractory bricks made by a slurry gelation and foaming method. J. Eur. Ceram. Soc. 33(15–16), 3429–3435 (2013)
S. Meille, M. Lombardi, J. Chevalier, L. Montanaro, Mechanical properties of porous ceramics in compression: on the transition between elastic, brittle, and cellular behavior. J. Eur. Ceram. Soc. 32, 3959–3967 (2012)
E.R. Bagherian, Development of a ceramic foam filter for filtering molten aluminium alloy in casting processes. Int. J. Res. Eng. Technol. 4(3), 27–43 (2015)
J. Geus, J. Van Giezen, Catalysts supported by porous ceramic layers on ceramic or metallic substrates. MRS Proc. 454, 147–153 (1996)
R.S. Barhate, S. Ramakrishna, Filtration problems and solutions from tiny materials. J. Membr. Sci. 296(1, 2), 1–8 (2007)
K.S. Chou, T.K. Lee, F.J. Liu, Sensing mechanism of a porous ceramic as humidity sensor. J. Adv. Ceram. Soc. 56(12), 106–111 (1999)
H. Takahara, The sound absorption characteristics of particulate porous ceramic materials. J. Adv. Ceram. 41(3), 265–274 (1994)
B.S.M. Seeber, U.T. Gonzenbach, L.J. Gauckler, Mechanical properties of highly porous alumina foams. J. Mater. Res. 28(17), 2281–2287 (2013)
N. Sarkar, J.G. Park, S. Mazumder, A. Pokhrel, C.G. Aneziris, I.J. Kim, Effect of amphiphile chain length on wet foam stability of porous ceramics. Ceram. Int. 41, 4021–4027 (2015)
T. Ohji, M. Fukushima, Macro-porous ceramics: processing and properties. Int. Mater. Rev. 57, 115–131 (2012)
Y. Zhu, Z. Huang, S. Dong, M. Yuan, D. Jiang, Manufacturing 2D carbon-fiber-reinforced SiC matrix composites by slurry infiltration and PIP process. Ceram. Int. 34(5), 1201–1205 (2008)
F.W. Zok, C.G. Levi, Mechanical properties of porous-matrix ceramic composites. Adv. Eng. Mater. 3(1, 2), 1527–2648 (2001)
B.H. Kim, Y.H. Na, Fabrication of fiber-reinforced porous ceramics of Al2O3-mullite and SiC-mullite systems. Ceram. Int. 21, 381–384 (1995)
J. Wang, M.R. Piramoon, C.B. Ponton, P.M. Marquis, A study in short ahnnina fiber reinforced mullite composites. Brit. Ceram. Trans. 90(4), 105–110 (1991)
H. Liu, C. Li, X. Ren, K. Liu, J. Yang, Fine platinum nanoparticles supported on a porous ceramic membrane as efficient catalysts for the removal of benzene. Sci. Rep. 7, 16589 (2017)
B. Basnet, H.M. Lim, K.S. Lee, I.J. Kim, Effects of carbon fiber on mechanical Behaviour Al2O3 Porous Ceramics. J. Korean Ceram. Soc. 56(5), 513–520 (2019)
U.T. Gonzenbach, A.R. Studart, E. Tervoort, L.J. Gauckler, Macroporous ceramics from particle-stabilized wet foams. J. Am. Ceram. Soc. 90(1), 16 (2007)
I.J. Kim, J.G. Park, H.Y. Han, S.Y. Kim, J.F. Shackelford, Wet foam stability from colloidal suspension to porous ceramics: a review. J. Korean Ceram. Soc. 56(3), 211–232 (2019)
S. Meille, M. Lombardi, J. Chevalier, L. Montanar, Mechanical properties of porous ceramics in compression: on the transition between elastic, brittle, and cellular behaviour. J. Eur. Ceram. Soc. 32, 3959–3967 (2012)
B.R. Lawn, Indentation of ceramics with spheres: a century after Hertz. J. Am. Ceram. Soc. 81(8), 1977–1994 (1998)
K.S. Lee, S.K. Kim, T.W. Kim, S. Kim, I.S. Han, S.K. Woo, Cracking of densely coated layer adhesively bonded to porous substrates under Hertzian stress. J. Mater. Sci. 42, 9116–9120 (2007)
K.S. Lee, Y.G. Jung, I.M. Peterson, B.R. Lawn, Model for cyclic fatigue of quasi-plastic ceramics in contact with speres. J. Am. Ceram. Soc. 83(9), 2255–2262 (2000)
Acknowledgements
This study was financially supported by Hanseo University.
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Byun, Y.M., Lee, G.W., Lee, K.S. et al. Mechanical properties of carbon fiber-reinforced Al2O3 porous ceramics. J. Korean Ceram. Soc. 58, 269–275 (2021). https://doi.org/10.1007/s43207-020-00105-1
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s43207-020-00105-1