Physiologic anchorage Speewire system

Physiologic anchorage Speewire system (PASS) technique is based on physiologic anchorage control theory. It is based on craniofacial growth, dentoalveolar compensation, physiologic curve of Spee, principle of differential moments, and the advantage of light force low friction. PASS appliance consists of XBT buccal tube and MLF bracket.


Materials/instruments
XBT buccal tube MLF bracket

Mechanism and procedure
Orthodontists used to attribute molar mesial displacement (anchorage loss) during orthodontic extraction treatment to reaction force of anterior teeth retraction. Our RCT study showed the amount of anchorage loss was not only affected by orthodontic retraction technique but also by growth rhythm and gender. Craniofacial longitudinal growth study also shows upper molar tips forward during 1 3 18 Page 2 of 6 growth as the compensation of mandible outgrows the maxilla. So we divided the anchorage loss during orthodontic treatment into two parts: one by orthodontic appliance-the mechanical anchorage loss; the other by physiologic force such as growth, occlusal force, periodontal ligament force, etc.-physiologic anchorage loss. The concept of physiologic anchorage control is if we can prevent upper molar forward tipping growth from the first NiTi archwire in aligning stage, do not level or restore upper posterior curve of Spee (it actually indicates upper buccal teeth gradually tipped back from premolar to the last molar) during following treatment, it will not only provide an strong anchorage similar to Tweed anchorage preparation mechanism in retraction stage, but also save more room to retract anterior teeth by aligning posterior teeth on a curved archwire rather than on a straight archwire. So we call this physiologic anchorage Speewire system (PASS).
In PASS, physiologic features of dentition are followed as much as possible and these features are used during orthodontic treatment. In this technique, the physiologic or compensated curve of Spee is kept in the posterior segment for function while straightening anterior teeth for esthetics.
The basic principle of physiologic anchorage control (PAC) technique is moving the teeth to the position in harmony with oral physiologic characteristics with PASS appliance.
The appliance is designed to reduce unfavorable force system in appliance and to take advantage of all physiologic forces in the mouth. In PAC system, the largest or dominant moment is on the anchor molar as its direction can be determined according to Burstone's six geometric classes between two neighboring teeth.
The PASS considers following forces and movements in the treatment mechanics: • Forces from muscles of lip, buccal area, and tongue • Tooth eruption force • Bite force • Periodontal ligament force • Taking first premolar extraction case as an example: according to physiologic anchorage loss theory, upper posterior teeth will tip forward with mandible forward growth (Fig. 1). • Molar XBT tube and anterior MLF brackets are bonded within 2 weeks after extraction (Fig. 2). • Initial thin NiTi wires are engaged in − 25° tip back tube on upper first molar and − 20° tip back "virtual tube" on lower first molar (Fig. 2). According to Burstone's six geometric classes, the larger moment will be on anchor molar because of the larger wire-slot angle. Canines in most cases will get the same direction but smaller moment if they are closed to normal angulation, so they will be tipped backward to relieve anterior crowding without laceback or tieback. The backward tipping moment on molar can only prevent molar forward tipping but cannot stop molar eruption with growth, so it changes upper molar growth pattern from downward and forward to downward and backward along with its long axis (Fig. 3), which may increase dental arch length. • When malocclusion teeth in the front are corrected to near normal or wire-slot angulation on all other teeth is less than 7° on upper arch and 4° on lower arch, then we bond second premolars and second molars, and − 7° rectangular tube on Fig. 3 The forward-tipping compensation of upper first molar is resisted by first NiTi wire in aligning stage, although it may still erupt along its long axis to compensate jaw differential growth rotation, which is supposed to be good for upper molar apex moving downward and backward to increase arch length the upper first molar and − 4° rectangular tube on the lower first molar are used (Fig. 4). In this way, the larger moment or dominant moment of the system is still on posterior teeth or anchor teeth. From this stage, all upper arch wires need normal or compensated curve of Spee to avoid leveling upper posterior curve of Spee, and lower archwire usually needs reverse curve of Spee to open the bite and enhance posterior anchorage until all extraction space is closed.

Pitfalls and complications
When straight NiTi wire is used to align irregular teeth, prediction of the force on each tooth becomes difficult.