NH3-Induced In Situ Etching Strategy Derived 3D-Interconnected Porous MXene/Carbon Dots Films for High Performance Flexible Supercapacitors

Highlights Porous MXene (p-MC) films with 3D-interconnected ion transmission paths are constructed by NH3-induced in situ etching strategy. The flexible p-MC film electrodes exhibit a superior capacitance of 688.9 F g−1 with a good rate capability. The as-assembled p-MC solid-state flexible supercapacitors reveal superior electrochemical performance (99.7 F g−1 at 1 A g−1) and excellent flexibility. Supplementary Information The online version contains supplementary material available at 10.1007/s40820-023-01204-4.

Constructing ion transport channels is an effective way to resolve the abovementioned bottle-neck problem of 2D MXenes.For example, introducing spacers into MXene layers can effectively enlarge the interlayer spacing of MXene sheets.In this regard, transition metal oxides (e.g., TiO 2 , SnO 2 , and Fe 3 O 4 ) [26][27][28], transition metal dichalcogenides (e.g., MoS 2 , and SnS 2 ,) [29,30], polymers (e.g., polypyrrole, and polyaniline) [31,32], and low-dimensional carbon materials [e.g., graphene, carbon nanotubes, and carbon dots (CDs)] [ [33][34][35][36] have been successfully inserted into MXene layers, thus creating substantial ion transport channels in the horizontal direction, and exposing more internal electrochemical active sites.However, the spacerintercalation strategy cannot reduce the high ion-path tortuosity in the direction normal to the MXene films, which would be an obstacle for fast ion transport and high rate capability.On the other hand, constructing in-plane pores on MXene sheets can effectively reduce the ion-path tortuosity and generate ion-transport microchannels in the vertical direction [37][38][39][40].However, this approach cannot increase the interlayer spacing of MXene sheets, and thus the ion diffusion in the horizontal direction is still limited.In this context, it is highly anticipated that the combination of introducing interlayer spacer and creating in-plane pores could form 3D interconnected ion transport channels and expose more internal electrochemical active sites, which 1 3

Preparation of p-MC and AC Electrodes
First, 3-18 mL of CDs solution (0.4 mg mL −1 ) was mixed with 10 mL of Ti 3 CNT x (5.1 mg mL −1 ) solution and stirred for 30 min.Then, the mixture was filtered under vacuum through cellulose membrane and dried under vacuum at 30 °C to fabricate MXene/Carbon dots (MC) films.The p-MC electrodes were finally obtained by annealing the MC electrodes at 350 °C for 1 h at the heating rate of 10 °C min −1 .The pure MXene films were prepared with the same method but without the addition of CDs.
As for the AC electrodes, 45 mg of AC (YP-50F, Kuraray) and 50 mg of polytetrafluoroethylene (PTFE, 10 wt% solution) were mixed and stirred for 10 min to form a suspension.Then, the suspension was dried at 80 °C to remove the solvent.The formed dough-like paste was repeatedly rolled into a thin AC film and cut into the same size (d = 12 mm) as p-MC electrodes.

Construction of p-MC-Based Flexible Solid-State Supercapacitors
The gel electrolyte (PVA/H 2 SO 4 ) was obtained by mixing the PVA (1799 type), deionized water, and concentrated H 2 SO 4 (mass ration of 10:1:1) and stirring at 80 °C for 1 h [44].To fabricate the p-MC-based supercapacitors, p-MC and AC films were pressed onto current collectors.Then, the PVA/H 2 SO 4 electrolyte was uniformly coated on the surface of p-MC and AC electrodes, followed by pairing them face to face and pressing together.The flexible solid-state supercapacitors were finally obtained by packaging the assembled electrodes with polydimethylsiloxane (PDMS) and drying them at 30 °C until the PDMS completely cured [45].

Material and Electrochemical Characterization
The morphologies of materials were characterized with the field emission scanning electron microscopy (SEM, FEI QUANTA FEG 250) and transmission electron microscopy (TEM, JEOL JEM-2100).The chemical structure of CDs was recorded by Fourier Transform Infrared Spectrometer (FTIR, TENSOR II).X-ray photoelectron spectroscopy (XPS) was recorded on Thermo Scientific ESCALAB 250Xi.Raman spectra were measured on confocal Raman microscope (HORIBA Jobin-Yvon XploRA).
The cyclic voltammetry (CV), galvanostatic charge-discharge (GCD), and electrochemical impedance spectroscopy (EIS) tests were performed on an electrochemical workstation (Chenhua CHI660E) in three-electrode system with AC electrode as counter electrode, Ag/AgCl in saturated KCl solution as reference electrode, and 1 M H 2 SO 4 as electrolyte.The EIS tests were conducted in the frequency range of 100 kHz to 0.01 Hz at open circuit potential.The cycling tests of the p-MC-based flexible solid-state supercapacitor were carried out with a multi-channel galvanostat/potentiostat instrument (Arbin USA).

Capacitance Calculations
The charge balance (Q + = Q − ) was achieved by balancing the mass of positive and negative electrodes according to the following equation: where m is the loading mass of AC and p-MC electrode, C electrode is the gravimetric capacitance, and ΔV is the potential window of each electrode.
The specific capacitance (C), power density (P), and energy density (E) were calculated according to the following equations: where I is the current, v is the scan rate.

Preparation of p-MC and Structural Characterizations
The design principle of p-MC composite films is schematically illustrated in Fig. 1.As shown in Route I, the conventional tightly stacked pure MXene films with a high As schematically illustrated in Fig. S1, the CDs were prepared through hydrothermal reactions (the detailed process can be found in Experimental Section).The TEM image in Fig. S2 shows that the obtained CDs possess uniform morphology with an average diameter of approximately 20 nm.Both CDs and MXene sheets are negatively charged in aqueous solutions (Fig. S3); thus, they can form a uniform and stable colloidal solution by mixing with each other owing to the electrostatic repulsion force.During the vacuum filtration process, the well dispersion of CDs and MXene sheets in the solution guarantees the uniform dispersion of CDs in the MXene/CDs (MC) composite film (the filter cake).In the thermal annealing process, the CDs with a variety of functional groups (e.g., −C=O, -COOH, -C-N) may react with the surface group (e.g., -OH, -F, and -O) on MXene sheets, thus anchoring the CDs onto the MXene sheets [46].After thermal annealing, the MC film was converted to p-MC film.The SEM images show that the MXene layers in p-MC film are significantly wrinkled with expanded interlayer spacing and well-distributed in-plane macropores (Fig. 2a, b).Such a structure can effectively expose more internal electrochemical active sites and shorten the ion transport path, resulting in better electrochemical performance, especially for the gravimetric capacitance and rate performance.It should be noted that the flexibility of p-MC films can be still maintained during the constructing of porous structure (Fig. S4), showing a bright prospect in flexible devices.For comparison, the conventional pure MXene film shows a densely packed structure without in-plane pores (Fig. 2c, d), which is unfavorable for ion diffusion.From the Raman spectrum in Fig. S5, both pure MXene and p-MC exhibit similar Raman peaks located between ~ 100 and ~ 800 cm −1 , which should be assigned to the A 1g and E g group vibrations of Ti and C atoms and surface functional groups [47].Comparing to the pure MXene, the two peaks of p-MC located at ~ 1350 and ~ 1580 cm −1 corresponding to the disordered-induced D-band and graphitic G-band of carbon, respectively, are much stronger, which should be ascribed to the contribution of CDs [47,48].X-ray diffraction (XRD) patterns indicate the intercalation of CDs does not change the basic crystal structure of p-MC (Fig. S6).XPS was carried out to identify the composition and chemical bonding information of pure MXene and p-MC films (Figs.2e, f, and S8-S9).In the highresolution C 1s XPS spectra (Fig. 2e, f), the p-MC shows a higher content of C-C bond than that of pure MXene.In addition, the peak at 288.3 eV, which corresponds to the -COOH group of CDs, can only be observed in p-MC [49][50][51][52].These results confirm the successful insertion of CDs into MXene layers.Compare to the N 1s spectrums of pure MXene (Fig. S8a, b), the peaks at 398.7 and 400.1 eV correspond to the pyrrolic nitrogen and pyridinic nitrogen of CDs [53][54][55], respectively, can only be observed in p-MC films too.These results are further in accordance with the abovementioned inference.

Formation Mechanism of 3D-Interconnected Pores for p-MC
To gain insight into the formation mechanism of p-MC film, a control experiment conducted under the identical synthetic conditions for p-MC film, but without CDs, produced a densely packed MXene film without any pores on its surface (Fig. S10), suggesting that the CDs play a critical role in the pore formation process.Considering no pores were observed in the pristine MC film before annealing (Fig. S11), the thermal annealing treatment is also a prerequisite for generating pores on MXene sheets.To further explore the pore formation mechanism of p-MC during the annealing process, in situ thermogravimetry-mass spectroscopy (TG-MS) and thermogravimetry-Fourier transform infrared spectroscopy (TG-FTIR) techniques were performed to monitor the gaseous products during the annealing of CDs.The TG-MS spectra (Fig. 3a) show that the pyrolysis of CDs generates many gaseous products, such as NH 3 , CO 2 , CO, and H 2 O [56][57][58].The TG-FTIR spectra (Figs.3b and S12) further confirm the generation of the abovementioned gases during the annealing process [59,60].To investigate whether these gases promote the formation of macropores on MXene sheets, we annealed pure MXene film under each of gases mentioned above and found that macropores were formed on the surface of MXene under NH 3 atmosphere (Fig. S13).Based on the above results, we infer that the NH 3 generated from the pyrolysis of CDs etches the MXene nanosheet during the annealing process, resulting in the formation of well-distributed in-plane macropores on MXene sheets (as illustrated in Fig. 3c).

Electrochemical Performance in a Three-Electrode System
Owing to the unique structural advantages, p-MC films are expected to exhibit superior electrochemical performance as flexible electrodes for supercapacitors.To assess the electrochemical properties of p-MC film, CV, GCD, and EIS measurements were conducted in three-electrode system in 1 M H 2 SO 4 .To obtain an optimized ratio of CDs in p-MC, the electrochemical properties of fresh and annealed MC films with CDs contents ranging from 0 to 18 mL are shown in Fig. S14.As can be seen, the MC films fabricated with a MXene-to-CDs volume ratio of 10:12 exhibit the highest specific capacitance and capacity retention.Therefore, this MXene-to-CDs volume ratio is used to fabricate the MC and p-MC films in the following discussion.Figure 4a compares the CV profiles of p-MC and pure MXene films in the potential window of −0.4 to 0.3 V (vs Ag/AgCl) at a scan rate of 5 mV s −1 .The intensity of the redox peaks for p-MC film is much stronger than that of the pure MXene film.Compare to the CV curves of pure MXene (Fig. S15), the CV curves of p-MC film (Fig. 4b) can retain their peak-shapes even at a high scan rate of 500 mV s −1 while the peak-shapes for pure MXene have already deformed at 100 mV s −1 , suggesting that the porous structure and the enlarged interlayer spacing can improve the ion accessibility to pseudocapacitive redox sites on MXene sheets.Figure 4c shows the gravimetric capacitances of the p-MC and pure MXene films.Compare to the pure MXene film (283.7 F g −1 ), the p-MC film delivered a much improved capacitance of 688.9 F g −1 at 2 A g −1 .With the current density increased to 100 A g −1 , the p-MC film can exhibit a high capacitance retention of 264 F g −1 , which is more than five times that of pure MXene film (51.4 F g −1 ).Thus, it could be concluded that the ion transport would be more efficient in a porous structure, which leads directly to the improved rate capability for p-MC film (Fig. 4c).
The GCD curves of p-MC and pure MXene electrodes in Fig. S16 are symmetric and nonlinear, which is different from the isosceles-triangular-shaped ideal capacitive behavior, reflecting their intrinsic charge storage mechanisms are the combination of pseudocapacitive and electrolytic double-layer capacitive (EDLC) mechanism.Additionally, the Nyquist plots (Fig. 4d) demonstrate that p-MC film exhibits smaller ohmic resistance (R s ) and charge transfer resistance (R ct ) than pure MXene (Table S1), revealing the faster charge-transfer kinetics within the p-MC film.The slopes of the straight-line in the Nyquist plots reflect the Warburg impedance of electrodes.The steeper slope of the linear region for p-MC film indicates that the 3D-interconnected porous structure facilitates fast ion diffusion [61].
To shed light on the charge storage mechanism of p-MC electrodes, a power law equation is used to analysis their electrochemical kinetic: where i is the peak current, ν stands for the scan rate, a and b are constants.The b value can be obtained by fitting the slope of the log (v)-log (i) plot (Fig. 4e).Generally, b = 0.5 indicates a diffusion-controlled process, while b = 1 reflects a surface capacitive process [62].The b value of p-MC is determined to be 0.98, implying that the charge storage is mainly governed by the surface capacitive process.The pseudocapacitive contributions to the total capacitance can be further quantified through the following formula (6): (5) i = av b where i(V) is the current response, ν stands for the scan rate, and k 1 v and k 2 v 1/2 correspond to the surface capacitive and diffusion-controlled process, respectively [63].The pseudocapacitive contributions of the p-MC and pure MXene films at a scan rate of 5 mV s −1 are shown in Fig. 4f.The pseudocapacitive contribution of p-MC is 68.8%, much higher than that of pure MXene (49.8%).Such a high proportion of pseudocapacitive contribution is attributed to the unique structural merits of p-MC film that the intercalation of CDs can help MXene layers expose more internal pseudocapacitive redox sites, leading to improved capacitance and rate performance.

Flexibility and Application of the p-MC-Based Supercapacitors
To further investigate the practical application potential of p-MC films, the flexible asymmetric all-solid-state supercapacitors were fabricated by taking p-MC film as the negative electrode and AC (active carbon) film as the positive electrode (the detailed assembly process can be found in Experimental Section).As shown in Fig. 5a, the MXene-based electrode and AC electrode exhibit the potential window of -0.4 to 0.3 V and 0 to 0.8 V, respectively, enabling the asymmetric devices to operate at a high potential of 1.2 V.With the scan rate increased from 5 to 50 mV s −1 (Fig. S17), a couple of redox peaks were still present on the CV curves of p-MC devices.As calculated from the GCD curves (Figs.5b and S18-S19), the p-MC-based asymmetric supercapacitor delivers capacitances of 99.8, 86.7, and 68.2 F g −1 at 1, 2, and 10 A g −1 , respectively, which are higher than those of pure MXene-based device.Figure 5c shows the Ragone plots of p-MC-based supercapacitors and many other previously reported MXene-based supercapacitors.The p-MC-based flexible supercapacitors deliver a maximum energy density 20 Wh kg −1 at a power density of 600 W kg −1 , which is higher than that of many reported MXene-based supercapacitors [47,[64][65][66][67][68][69][70].Furthermore, Fig. 5d depicts the long-term cycling stability of p-MC-based supercapacitor, where a high capacitance retention of 90% (with a superior Coulombic efficiency of 99.5%) is maintained after 10,000 cycles, indicating its excellent cycling stability.
To meet the urgent demand for high operating voltage and high-capacity applications, the p-MC-based supercapacitors are integrated together in series and in parallel.As depicted in Fig. 5e, f, two p-MC-based supercapacitors constructed in series afford an operating voltage of 2.4 V, which is twice that of a single device, enabling high energy output (E = 1/2 CV 2 ).When constructing two p-MC-based supercapacitors in parallel, the obtained device can deliver nearly doubled discharge time as well as current output.The solid-state supercapacitors can be bent at various angles (i.e., 0°, 15°, 60°, and 90°), demonstrating their good mechanical flexibility (Fig. 5g).In addition, the CV curves of the p-MC-based supercapacitor under various bending angles (0° to 90°) are almost unchanged (Fig. 5h), suggesting that the device can maintain a stable energy-output during the distorting process.As a demonstration, a panel integrated with about 400 LEDs can be successfully powered by the five-tandem cells (Fig. 5i), showing the great practical application potential of the flexible p-MC-based supercapacitors.

Conclusions
In summary, a flexible and 3D-interconnected porous MXene/ Carbon Dots (p-MC) composite film was fabricated via a facile thermal annealing process for high-performance flexible supercapacitor.The introducing of CDs enlarges the interlayer spacing of MXene nanosheets, allowing the exposure of more inner pseudocapacitive redox sites and efficient ion diffusion.Comprehensive characterizations reveal that the NH 3 released from the pyrolysis of CDs etches the MXene nanosheets and creates well-distributed in-plane macropores, thus reducing the ion-path tortuosity in the vertical direction and guaranteeing fast ion transportation.When used as electrode for flexible supercapacitor, p-MC film delivers a high specific capacitance of 688.9 F g −1 at 2 A g −1 and maintain a high capacitance of 264.3 F g −1 even at 100 A g −1 .Moreover, the p-MC film-based asymmetric flexible supercapacitor exhibits a high energy density (20 Wh Kg −1 ) and superior cycling stability (90% capacitance retention after 10,000 cycles).This work proposes an efficient strategy for constructing porous flexible MXene films and may pave the way to develop high-performance supercapacitors.
tortuosity usually led to sluggish ion transport kinetics and low accessibility of electrochemical active sites to ions, which is detrimental to the rate performance and gravimetric capacitance of the electrodes.For comparison, the p-MC films obtained by vacuum filtration of a colloidal solution containing MXene nanosheets and CDs and annealing at 350 °C under Ar flow (shown in Route II) present three advantages: (i) the evenly intercalated CD spacers can effectively prevent the serious restacking of Ti 3 CNT x nanosheets and broaden the interlayer spacing to expose more electrochemical active sites, thus increasing the horizontal ion-accommodation; (ii) the in-plane macropores can act as buffering reservoirs for electrolyte to reduce electrochemical response time; (iii) the in-plane porous structure can significantly reduce the ion-path tortuosity in the vertical direction, facilitating rapid ion transfer.These merits endow the p-MC electrodes with high capacitance and rate capability.

Fig. 1
Fig. 1 Schematic illustration of the fabrication process of p-MC film and the advantages of p-MC film over traditional pure MXene film

Fig. 2 a
Fig. 2 a Top-view and b cross-sectional SEM images of p-MC film.c Top-view and d cross-sectional SEM images for pure MXene film.The C 1s XPS spectra of e p-MC and f pure MXene films

Fig. 3 a
Fig. 3 a Gaseous evolution curves of CDs during pyrolysis in TG-MS.b TG-FTIR spectra for volatiles at various temperatures for CDs.c Schematic diagram for the conversion process of p-MC film

Fig. 4
Fig. 4 Electrochemical performance of pure MXene and p-MC films.a CV curves of pure MXene and p-MC films at 5 mV s −1 .b CV curves of p-MC film from 5 to 500 mV s −1 .c Gravimetric capacitances versus current densities for pure MXene and p-MC films.d Nyquist plots of pure MXene and p-MC films.e Plots of the log(anodic peak current) versus log(scan rate).f Comparison of the capacitance contribution for pure fresh MXene and p-MC films at a scan rate of 5 mV s. −1

Fig. 5 a
Fig. 5 a CV curves of pure MXene and AC films at 5 mV s −1 .b GCD curves of pure MXene and p-MC-based asymmetric all-solid-state flexible supercapacitors at a current density of 1 A g −1 .c Ragone plots of p-MC and other MXene-based supercapacitors.d Cycling stability performance of p-MC-based supercapacitor at a current density of 8 A g −1 .e CV curves at 10 mV s −1 , f GCD curves at 5 A g −1 for single and two p-MC devices connected in series and in parallel.g Optical photographs of p-MC-based supercapacitors under various bending angles.h CV curves of the p-MC devices bending at various angles.i Hundreds of LEDs powered by p-MC-based supercapacitors