Pore structure of low-permeability coal and its deformation characteristics during the adsorption–desorption of CH4/N2

The pore structure of coal plays a key role in controlling the storage and migration of CH4/N2. The pore structure of coal is an important indicator to measure the gas extraction capability and the gas displacement effect of N2 injection. The deformation characteristic of coal during adsorption–desorption of CH4/N2 is an important factor affecting CH4 pumpability and N2 injectability. The pore structure characteristics of low-permeability coal were obtained by fluid intrusion method and photoelectric radiation technology. The multistage and connectivity of coal pores were analyzed. Subsequently, a simultaneous test experiment of CH4/N2 adsorption–desorption and coal deformation was carried out. The deformation characteristics of coal were clarified and a coal strain model was constructed. Finally, the applicability of low-permeability coal to N2 injection for CH4 displacement technology was investigated. The results show that the micropores and transition pores of coal samples are relatively developed. The pore morphology of coal is dominated by semi-open pores. The pore structure of coal is highly complex and heterogeneous. Transition pores, mesopores and macropores of coal have good connectivity, while micropores have poor connectivity. Under constant triaxial stress, the adsorption capacity of the coal for CH4 is greater than that for N2, and the deformation capacity of the coal for CH4 adsorption is greater than that for N2 adsorption. The axial strain, circumferential strain, and volumetric strain during the entire process of CH4 and N2 adsorption/desorption in the coal can be divided into three stages. Coal adsorption–desorption deformation has the characteristics of anisotropy and gas-difference. A strain model for the adsorption–desorption of CH4/N2 from coal was established by considering the expansion stress of adsorbed gas on the coal matrix, the compression stress of free gas on the coal matrix, and the expansion stress of free gas on micropore fractures. N2 has good injectability in low-permeability coal seams and has the dual functions of improving coal seam permeability and enhancing gas flow, which can significantly improve the effectiveness of low-permeability coal seam gas control and promote the efficient utilization of gas resources. The pore structure characteristics of low-permeability coal were obtained by fluid intrusion method and photoelectric radiation technology. The multistage and connectivity of coal pores were analyzed. A simultaneous test experiment of CH4/N2 adsorption–desorption and coal deformation was carried out. The deformation characteristics of coal were clarified and a coal strain model was constructed. The applicability of low-permeability coal to N2 injection for CH4 displacement technology was investigated. The pore structure characteristics of low-permeability coal were obtained by fluid intrusion method and photoelectric radiation technology. The multistage and connectivity of coal pores were analyzed. A simultaneous test experiment of CH4/N2 adsorption–desorption and coal deformation was carried out. The deformation characteristics of coal were clarified and a coal strain model was constructed. The applicability of low-permeability coal to N2 injection for CH4 displacement technology was investigated.

• The pore structure characteristics of low-permeability coal were obtained by fluid intrusion method and photoelectric radiation technology.The multistage and connectivity of coal pores were analyzed.• A simultaneous test experiment of CH 4 /N 2 adsorptiondesorption and coal deformation was carried out.The deformation characteristics of coal were clarified and a coal strain model was constructed.• The applicability of low-permeability coal to N 2 injection for CH 4 displacement technology was investigated.

Introduction
Coal is a complex porous medium, and its pore characteristics have an important impact on gas storage (adsorption) and migration (desorption-diffusion-seepage) (Zhang et al. 2022a).Coal pores can be divided into adsorption pores (< 100 nm) and seepage pores (> 100 nm).The former is the main space for gas adsorption, desorption, and diffusion, and the latter is the main channel for gas seepage (Sang et al. 2005;Lu 2016).The fine characterization of coal pore structure is of great significance for the in-depth study of gas adsorption and desorption characteristics and coal deformation characteristics (Wen et al. 2023;Wang et al. 2022).
Low-temperature gas adsorption, high-pressure mercury intrusion, and low-field nuclear magnetic resonance (NMR) are commonly used in the coal industry to determine the pore structure of coal, resulting in a variety of coal pore division types (Hu et al. 2023;Cheng and Hu 2023;Hodot 1966).Among them, the HODOT B.B. pore classification method is widely accepted because it fully considers the flow characteristics of gases in pore structures of different sizes: micropores (< 10 nm), transition pores (10-100 nm), mesopores (100-1000 nm), and macropores (1-100 μm).
Both coal mining and gas extraction involve issues such as the interaction between coal and gas, and the mechanical behavior of gas adsorption-desorption (Zhu et al. 2018;Lin et al. 2023a).In-depth research on gas adsorption-desorption characteristics and coal deformation characteristics is of great significance to improve the effectiveness of gas extraction.In the past, researchers mostly started from the adsorption expansion and desorption shrinkage deformation characteristics of coal, and introduced the coal deformation coefficient to establish models to characterize the relationship between coal adsorption deformation and gas adsorption amount or desorption deformation and gas desorption amount (Zhang et al. 2022b(Zhang et al. , 2021)).And the Langmuir-like equation is often used to describe the coal deformation characteristics of adsorption expansion/desorption shrinkage (Lin et al. 2017).Related studies have shown anisotropy in coal deformation during gas adsorption/desorption.The mechanical strength of coal also decreases after gas adsorption, and the elastic modulus will decrease at the macroscopic level, which is inconsistent with the assumptions of conventional models describing coal deformation (He et al. 2018;Ranjith et al. 2010).The applicability and reliability of the existing coal deformation models need to be further investigated.
Based on the pore structure parameters of low-permeability coal measured by low-temperature gas adsorption, high-pressure mercury intrusion, and low-field NMR experiments, the author conducted a detailed characterization of the coal pore structure and obtained the fractal characteristics and tortuous connectivity of the coal pore structure.The simultaneous test experiments of CH 4 /N 2 adsorption-desorption and coal deformation were carried out by using the flow-solid coupling experimental system for coal seam gas.The influence law of gas type/gas pressure on coal deformation is quantitatively characterized.A strain model for coal at each stage of CH 4 /N 2 adsorption-desorption was constructed.The applicability of coal samples to the N 2 injection for CH 4 displacement technology is investigated.To provide a theoretical basis for high-efficiency extraction of gas from low-permeability coal seams.

Parameters determination and preparation of coal samples
Coal samples were collected from low-permeability mines in the Qinshui Basin, China.The basic parameters were determined after sampling, as shown in Table 1.Coal pore structure characterization experiments take pulverized coal, granular coal, and cylindrical standard coal samples as research objects.The coal samples are taken from large coal blocks without gangue, and the specific sample specifications are prepared according to the equipment requirements.The simultaneous test experiment of CH 4 /N 2 adsorption-desorption and coal deformation takes the cylindrical standard coal samples as the research object.Pulverized coal, granular coal, and Φ50 mm × 100 mm cylindrical standard coal samples are shown in Fig. 1a.

Screening and treatment of coal samples
The screening process of the cylindrical standard coal samples consists of initial screening and secondary screening, as illustrated in Fig. 1b.(1) Initial screening: Select coal samples with neat ends, no impurities, and no cracks.Subsequently, the non-metallic acoustic detector is used to detect the internal defects of the coal and screen out the coal samples with uniform texture.(2) Secondary screening: The height, diameter, and quality of the coal samples were measured, and those with excessively different values were rejected.Subsequently, the screened coal samples are dried to constant weight by using a vacuum drying oven.
The handling process of cylindrical standard coal samples includes strain gauge installation and sealing treatment, as depicted in Fig. 1c.(1) Strain gauge installation: Two strain gauges are installed on the side surface along the axial/radial direction of the coal sample to monitor the deformation of the coal sample in real-time.(2) Sealing treatment: Apply sealant to the side surface of the coal sample and let it airdry.Then, a heat-shrinkable rubber sleeve is applied and a blower is used to soften and shrink the heat-shrinkable rubber sleeve.Finally, sealant is applied to the edges of both ends of the coal sample and let it air-dry to prevent gas from escaping during the experiment.

Experimental system
The simultaneous experiment of CH 4 /N 2 adsorption-desorption and coal deformation was carried out by the flowsolid coupling experimental system for coal seam gas of Xi'an University of Science and Technology.The system mainly consists of a stress loading system, axial/circumferential strain measurement and acquisition system, gas data Fig. 1 Experimental coal samples measurement and acquisition system (collect gas pressure data in real-time, and calculate gas adsorption and desorption volumes under different equilibrium pressures based on coal sample quality and gas pressure.),temperature control system, evacuation system, and auxiliary system, as described in Fig. 2.

Experimental condition and process
In order to investigate the CH 4 /N 2 adsorption-desorption law and the deformation characteristics of coal during the whole experiment, the experimental conditions were designed by the controlled variable method.The initial gas adsorption pressure, the experimental temperature, and the axial pressure/confining pressure loaded on the coal (according to the buried depth of the coal seam, the bulk density of the overlying strata, and the gas pressure, as well as combined with the similarity theory to calculate) are set according to the gas occurrence characteristics of the coal seam at the sampling location.According to the field measurement and theoretical calculation, the axial pressure/confining pressure was set to 2.5/2.0MPa, the experimental temperature was set to 303 K, and the initial CH 4 /N 2 adsorption pressure was set to five pressure gradients (0.74 MPa, 0.94 MPa, 1.14 MPa, 1.34 MPa, and 1.54 MPa).Experimental steps: (1) Coal sample installation.Apply axial pressure/confining pressure to the preset pressure step by step on the sealed coal sample.(2) Airtightness test.Fill the reactor with a certain pressure of He and leave it for 6 h.The air pressure value remains unchanged to prove good airtightness.(3) Free space volume calibration.Calibrate the total free volume, the free volume at the inlet end, and the free volume at the exhaust end of the experimental system.(4) Vacuum degassing.The coal samples were degassed under vacuum for 6 h.(5) Gas adsorption equilibrium.Adsorb gas at a preset gas pressure.The coal strain of the process is collected, and when the air-pressure value and the strain curve are stable at the same time, it indicates that the adsorption has reached equilibrium.(6) Gas desorption equilibrium.The coal samples with adsorption equilibrium were desorbed under atmospheric pressure.The coal strain of the process is collected and when the flow meter indicates 0, it is determined that the desorption has reached equilibrium.
3 Joint characterization of pore structure in low-permeability coal

Multimethod for determination of coal pore structure
The micropore distribution characteristics of coal samples were obtained by the low-pressure CO 2 adsorption experiment, as presented in Fig. 3a.The pore diameter of coal samples has peaks at 0.35 nm, 0.48 nm, 0.55 nm, and 0.83 nm.Among them, the half-peak width at 0.35 nm is narrower, the half-peak width at 0.83 nm is wider, and the pores at 0.48 nm and 0.55 nm have the largest distribution.The distribution characteristics of transition pores/mesopores in coal samples were obtained by the low-temperature N 2 adsorption experiment, as illustrated in Fig. 3b.The poresize distribution of the coal samples was bimodal, with the Axial/Circumferential strain measurement system, C-14 Gas data measurement system peak at 50 nm higher than the peak at 5 nm.There is a significant adsorption hysteresis phenomenon in the adsorption curve, which is related to the capillary coalescence phenomenon that occurs in the high relative pressure region (Li et al. 2023).According to the IUPAC classification of hysteresis loop, the coal sample is consistent with the H2 type hysteresis loop, indicating that the coal contains a high number of semi-open pores (wedge type, ink bottle type), which are conducive to gas adsorption and storage, but not conducive to gas migration (Gregg and Sing 1982).
The distribution characteristics of mesopores/macropores of coal samples were obtained by the high-pressure mercury intrusion experiment, as depicted in Fig. 3c.There is an obvious mercury intrusion hysteresis loop in the mercury intrusion curve, indicating that the pores of the coal samples are mostly semi-closed pores with poor pore connectivity, which is corroborated by the results of the low-temperature N 2 adsorption experiment.The results of the low-field NMR experiment are shown in Fig. 3d.The T 2 distribution curve was in the shape of three peaks.The relaxation times of the wave peaks were distributed at 0.5 ms, 5.0 ms, and 70.0 ms, and mainly concentrated at 0.5 ms, indicating that the micropores and transition pores of the coal samples were relatively developed.

Multimethod for joint characterization of coal pore structure
Low-pressure CO 2 adsorption, low-temperature N 2 adsorption, and high-pressure mercury intrusion all have their dominant pore-size segments (pore-size ranges with high test accuracy).To finely characterize the coal pore structure, the dominant pore-size segments of each test method were stitched together.Related studies have shown that low-pressure CO 2 adsorption is an ideal tool for micropore testing, which can accurately characterize the micropore distribution at < 2 nm (Liu et al. 2021).Low-temperature N 2 adsorption has high testing accuracy for micropores/transition pores (2-50 nm) (Lin et al. 2019).High-pressure mercury intrusion can be tested for mesopores/macropores. Due to the compressibility of coal, when the mercury injection pressure is > 10 MPa, the coal matrix is prone to compressive deformation/destruction, which will affect the accuracy of the experiment.Therefore, high-pressure mercury intrusion was chosen to characterize the pore distribution at > 50 nm (Liu et al. 2022).
The joint characterization results of the coal pore-size (Fig. 4) show that the pore-size distribution of the coal samples is multi-peaked and dominated by micropores (which provide a high number of adsorption vacancies for gas adsorption), with a certain proportion of transition pores and mesopores, and the smallest proportion of macropores.
Fractal theory is widely used to characterize the complexity of coal pore structure.There are various methods to calculate the fractal dimension and each has its own characteristics (Jiang et al. 2021).The FHH model is suitable for characterizing the fractal features of the pore structure in micropores and transition pores (Jia et al. 2021).The Menger model is suitable for characterizing the fractal features of the pore structure in mesopores/macropores (Chen et al. 2020).The fractal characteristics of the pore structure in coal samples are shown in Table 2.
From the low-temperature N 2 adsorption curve, it can be known that the gas adsorption mechanism is different for P/P 0 > 0.5 and P/P 0 < 0.5.For this purpose, the fractal dimension of both (D 11 , D 12 ) was calculated separately using the FHH model.The fractal dimension of the pore structure for pore-size < 100 nm is obtained.It is calculated that D 11 = 2.85 < D 12 = 2.54, which indicates that the pore structure of the micropores and transition pores in coal samples is generally complex, and the pore structure of micropores is more complex.According to the experimental data of high-pressure mercury intrusion, the Menger model was used to calculate the fractal dimension of the pore structure with pore-size > 100 nm.It is calculated that D 2 = 2.61 < 3, which indicates that the pore structure of mesopores and macropores in coal samples is equally complex.Altogether, the pore structure complexity of micropores in coal samples was greater than that of mesopores/macropores than that of transition pores.

Tortuous connectivity of coal pore structure
Tortuosity (τ) is a pore characterization parameter that quantitatively characterizes the tortuosity of the seepage channel.Tortuosity is defined as the ratio of the actual length of the seepage channel to the apparent length through the seepage medium (Dullien 2012;Attia 2005;Yu et al. 2003).It is calculated that τ = 5.81, which indicates that the seepage channel of the coal sample is tortuous and the gas flow is difficult.In low-permeability coal, the pores are mostly closed-pores, so the degree of pore connectivity also needs to be considered.The total porosity, effective porosity, and residual porosity of the  2 Fractal dimension of pore structure based on FHH model/Menger model Note: V is the pore volume corresponding to the relative pressure, cm 3 /g; P 0 is the saturated vapor pressure of the adsorbed gas; MPa; P is the system equilibrium pressure, MPa coal samples were calculated based on the T 2 distribution curves in the saturation/centrifugation condition, and then the pore connectivity rate was obtained, as described in Fig. 5a, b.The effective porosity of the coal sample was calculated to be 3.04%, and the pore connectivity rate was 40.36%.The pore connectivity rate of pore-size < 10 nm is relatively low, indicating that the pore connectivity of transition pores, mesopores and macropores in coal samples is good, and the pore connectivity of micropores is poor.
It can be known that the pore connectivity is related to the pore-size.The relationship between pore connectivity rate, pore percentage, and pore-size is shown in Fig. 5c.As the pore-size increases, the proportion of pores in each pore-size segment decreases, while the pore connectivity rate shows a gradual trend.The pore connectivity rates of < 10 nm, 10-100 nm, 100-1000 nm, and > 1000 nm pore-size segments were 10.96%, 91.36%, 96.32%, and 100%, respectively.It is due to the pore-size of micropores is small, which has a lower probability of forming connected pore groups, resulting in a weak pore connectivity rate.However, the pore-size of transition pores, mesopores and macropores is larger, which has a higher probability of forming connected pore groups, resulting in a higher pore connectivity rate.

Adsorption and desorption characteristics of CH 4 /N 2
The variation pattern of CH 4 /N 2 adsorption amount with experimental time is shown in Fig. 6.With the prolongation of the adsorption time, the adsorption amount of CH 4 / N 2 showed a trend of rapid growth-slow growth-flattening.As the gas pressure increases, the adsorption amount of CH 4 /N 2 gradually increases.When the gas pressure increased from 0.74 to 1.54 MPa, the adsorption amount of CH 4 and N 2 increased by 111.11% and 76.92%, respectively.With the prolongation of the desorption time, the adsorption amount of CH 4 /N 2 presents a trend of rapid decreaseslow decrease-leveling.As the gas pressure increases, the amount of CH 4 /N 2 desorption gradually increases.When the gas pressure increased from 0.74 to 1.54 MPa, the desorption amount of CH 4 and N 2 increased by 132.07%and 90.87%, respectively.
Existing studies have shown that the variation law of CH 4 /N 2 adsorption amount with adsorption time and desorption time conforms to the Langmuir-type equation (Eq.( 1)) (Meng et al. 2021).Fitting the experimental data of the adsorption amount of CH 4 and N 2 are found (Table 3): The value of A a increases with the increase of gas pressure, and the value of B a shows an overall increasing trend, indicating that increasing the gas pressure not only increases the amount of CH 4 /N 2 adsorbed by coal, but also effectively increases the adsorption energy (adsorption interaction between coal molecules and gas molecules), resulting in a sharp increase in the adsorption amount curve.The A d value increases with the increase of gas pressure, and the overall change of B d value is not significant, indicating that increasing the gas pressure has the same promoting effect on enhancing the amount of CH 4 /N 2 desorbed from the coal.
where, Q a is the gas adsorption amount at the time of t a , mol; A a is the gas saturation adsorption amount, mol; B a is the constant related to the adsorption time, s −1 ; t a is the adsorption time, s; Q d is the gas adsorption amount at the time of t d , mol; C d is the gas adsorption amount at the adsorption equilibrium, mol; A d is the ultimate gas desorption amount, mol; B d is the constant related to the desorption time, s −1 ; t d is the desorption time, s.
The CH 4 /N 2 adsorption amount-desorption amount-residual adsorption amount after coal adsorption/desorption equilibrium is shown in Table 4.As the gas pressure increases, the amount of CH 4 and N 2 adsorbed/desorbed by the coal increases.Under the same gas pressure, the amount of CH 4 adsorbed by the coal is greater than that of N 2 , the amount of CH 4 desorbed by the coal is greater than that of N 2 , and the amount of residual CH 4 adsorbed by the coal is greater than that of N 2 .Under different gas pressures, the residual adsorption volumes of CH 4 and N 2 were 55.2-79.0 and 13.2-28.2mL, respectively.

Deformation characteristics of coal
The variation pattern of the adsorption strain/desorption strain of coal with experimental time is shown in Fig. 7.In the adsorption process, the axial strain/volumetric strain of coal can be divided into three stages: initial compressive strain, adsorption expansion strain, and strain equilibrium.The circumferential strain is divided into three stages: initial expansion strain, adsorption expansion strain, and strain equilibrium (Lin et al. 2023b).For the desorption process, the axial strain/volumetric strain of coal is divided into three stages: initial expansion strain, desorption shrinkage strain, and strain equilibrium.The circumferential strain is divided into three stages: initial compression strain, desorption shrinkage strain, and strain equilibrium.
The main reasons are: (1) Initial expansion/compression strain stage: After the gas desorption experiment starts, (1) the gas pressure at the exhaust end is instantly deflated, the force in the axial direction of coal is reduced, and the expansion deformation occurs first in the axial direction and the shrinkage deformation occurs first in the circumferential direction.(2) Desorption shrinkage strain stage: Coal continuously desorbs gas and its shrinkage deformation occurs.(3) Strain equilibrium stage: With the extension of the desorption time, the gas no longer precipitates out of the coal, and the axial/circumferential strain of the coal tends to be smooth.
Existing studies show that the variation law of coal strain with adsorption time/desorption time follows the Langmuir-type equation (Eq.( 2)) (Li et al. 2018).Fitting the experimental data of coal strain revealed (Table 5): where, ε a is the strain generated by the adsorbed gas of coal at the time of t a , με; D a is the ultimate expansion strain generated by the adsorbed gas of coal, με; E a is the constant associated with the adsorption time, s −1 ; F a is the initial compression/expansion strain of coal during the adsorption process, με; ε d is the strain generated by the adsorbed gas of coal at the time of t d , με; F d is the equilibrium strain of (2) the adsorbed coal, με; G d is the initial compression/expansion strain of the desorbed coal during desorption, με; D d is the ultimate shrinkage strain generated by the desorbed gas of coal, με; E d is the constant related to the desorption time, s −1 .
(1) When coal adsorbs CH 4 , D a and E a increase with the increase of gas pressure.When coal adsorbs N 2 , D a increases with the increase of gas pressure and E a shows an overall increasing trend.Under the same gas pressure, D a for CH 4 adsorption is greater than D a for N 2 adsorption.E a for CH 4 adsorption is less than E a for N 2 adsorption.The above phenomenon shows that increasing the gas pressure not only improves the adsorption expansion amount of coal, but also effectively enhances the expansion strain energy (the difficulty of coal expansion caused by gas adsorption), resulting in a sharp increase in the strain curve.Under the same gas pressure, the adsorption expansion ability of coal when adsorbing CH 4 is stronger than that of N 2 , but the expansion strain energy when adsorbing CH 4 is weaker than that of N 2 (Jin and Huang 2015).
(2) When coal desorbs CH 4 /N 2 , D d increases with the increase of gas pressure and E d shows an overall increasing trend.At the same gas pressure, D d for the The above phenomenon shows that increasing the gas pressure not only improves the desorption shrinkage amount of coal but also effectively enhances the shrinkage strain energy (the difficulty of coal shrinkage deformation caused by gas desorption), resulting in a sharp decrease in the strain curve.Under the same gas pressure, the shrinkage deformation ability of coal when desorbing CH 4 is stronger than that of N 2 , but the shrinkage strain energy when desorbing CH 4 is weaker than that of N 2 .
The residual adsorption strain of coal after desorption of CH 4 /N 2 equilibrium at different gas pressures is shown in Fig. 8.The total residual adsorption strain of coal shows that the volume residual adsorption strain is greater than the axial residual adsorption strain than the circumferential residual adsorption strain.The residual adsorption strain generated when coal adsorbs CH 4 is greater than that generated when coal adsorbs N 2 .This is because the residual adsorption amount of CH 4 in coal is greater than the residual adsorption amount of N 2 after the gas desorption reaches the equilibrium state.
With the increase of CH 4 pressure, the decreased rate of residual adsorption strain of coal gradually increases.While with the increase of N 2 pressure, the decreased rate of residual adsorption strain of coal remains unchanged.The reason is that coal has a very strong adsorption capacity for CH 4 (under the same equilibrium pressure condition, the reduction of surface free energy when coal adsorbs CH 4 is greater than that of adsorbing N 2 ).According to the theory proposed by Bangham that the amount of solid expansion deformation is proportional to the amount of surface free energy reduction (Xie and Huang 1985), it can be known that the more gas adsorbed by coal, the greater the reduction in surface free energy, the greater the expansion deformation caused by gas adsorption, and the more obvious the weakening damage to the coal.Therefore, the modification effect of adsorbed CH 4 on the pore structure of coal is stronger than that of adsorbed N 2 .And the higher the pressure of CH 4 , the more significant the modification effect on the pore structure, resulting in an increase in the reduction rate of the residual adsorption strain in the coal.

Correlation between coal deformation and gas adsorption amount
The relationship between the adsorption expansion strain of coal and the equilibrium adsorption amount of CH 4 / N 2 is shown in Figs.9a, b.The expansion strain of coal adsorbed CH 4 is greater than that of adsorbed N 2 for the same amount of adsorption.The expansion strain of the coal increases exponentially as a function of CH 4 adsorption.The adsorption expansion strain rate gradually decreases with the increase of CH 4 adsorption, and the axial strain rate changes significantly.The adsorption expansion strain of coal shows a one-dimensional growth function with the increase of N 2 adsorption amount (ε 1 , ε 2 , and ε 3 are the axial strain, circumferential strain, and volumetric strain of the coal during the adsorption process, q 1 is the CH 4 /N 2 adsorption amount, H ac -I an is related fitting constants).
The main reason is that the bedding of the experimental coal sample is perpendicular to the axial direction of the coal.When the coal adsorbs gas, the bedding has strong adsorption deformation amount, and the coal has stronger adsorption amount for CH 4 than for N 2 .As the amount of CH 4 adsorption increases, the adsorption vacancies in the coal are continuously occupied by CH 4 molecules, resulting in a large expansion strain, and this strain first appears in the direction vertical to the bedding plane, resulting in a larger axial strain rate of the coal when the adsorption amount is small.As the adsorption continues, the remaining adsorption vacancies in the coal decrease, and the expansion strain rate caused by adsorption decreases, which shows that the axial strain rate of the coal decreases with the increase of the adsorption amount when adsorbing CH 4 .
The relationship between coal desorption shrinkage strain and CH 4 /N 2 equilibrium desorption amount is shown in Figs.9c, d.Under the same amount of desorption, the shrinkage strain of coal desorbed CH 4 is greater than that of desorbed N 2 .The desorption shrinkage strain of coal increases exponentially as a function of CH 4 desorption, and the desorption shrinkage strain rate decreases gradually with the increase of N 2 desorption amount, and the change of axial strain rate is obvious.The desorption shrinkage strain of coal increases with the increase of N2 desorption amount as a linear function of one variable (ε 4 , ε 5 , ε 6 are the axial strain, circumferential strain, and volumetric strain of the coal during the desorption process, q 2 is the desorption amount of CH 4 /N 2 , H dc -I dn are related fitting constants) (Table 6).

Gas occurrence pattern
The form of gas occurrence in coal is the basis for the investigation of its adsorption-desorption-diffusion-seepage characteristics.There are differences in the forms of gas occurrence within pores with different sizes.Among them, the adsorption force fields of the micropores superimpose the potential energy, resulting in gas enrichment mainly in the form of filling.Larger pores are dominated by gas surface coverage (Cheng and HU B. 2021).Related studies have shown that the van der Waals force on gas molecules is significantly enhanced in < 1.5 nm micropores, while the forces generated between gas molecules and pore-walls in larger pores have a relatively limited range of influence.This is because the gas adsorption in the > 1.5 nm pore-size segment belongs to supercritical adsorption and is dominated by monomolecular layer adsorption (Ortiz et al. 2016).Based on the difference of van der Waals forces on gas molecules in pores with different sizes, < 1.5 nm micropores can be divided into the strong-adsorption potential region (forced by the micropore wall) and the weak-adsorption potential region (force between adjacent gas molecules).Transition pores, mesopores, and macropores can be divided into   (Zhang et al. 2022c).
Coal has a complex network of pores and fractures, and gas molecules not only have different adsorption forms in multi-level pores, but also have different migration modes.The > 1.5 nm pores consist of diffusion pores (1.5-100 nm) and seepage pores (> 100 nm).Among them, the diffusion modes of gas molecules in the diffusion pores include gasphase diffusion, surface diffusion, and crystal diffusion, and gas-phase diffusion is dominant.The seepage modes of the gas molecules in the seepage holes include low-velocity non-Darcy flow, Darcy flow, and high-velocity non-Darcy  10.In general, most of gas molecules in coal are mainly attached to the multilevel pores in the adsorbed state, while a few gas molecules exist in the free state.
The adsorption of gas by coal belongs to physical adsorption.The strength of physical adsorption depends on the interaction between the two, which in turn affects the amount of gas adsorption.The molecular dynamics diameter, critical temperature, and diffusion velocity of the gas are important factors affecting the amount of gas adsorption.Gas with smaller molecular dynamics diameter, higher critical temperature, and faster diffusion rate is more easily adsorbed.
The basic physical parameters of CH 4 /N 2 are shown in Table 7.The molecular dynamic diameter of CH 4 is larger than that of N 2 , and the critical temperature and dynamic viscosity coefficient of CH 4 are smaller than those of N 2 .Although N 2 can enter the coal pores with smaller sizes, the experimental coal samples have less pore-size distribution in the range of 0.36-0.38nm, so the pore-size range accessible by CH 4 /N 2 is the same.And the critical temperature and dynamic viscosity coefficient of N 2 are greater than that of CH 4 , which shows that the adsorption amount of coal for CH 4 is greater than that for N 2 .

Coal deformation characteristics
The deformation of the coal caused by gas migration is due to the combined action of adsorbed gas and free gas.The former causes expansion deformation of the coal by reducing the surface free energy of the coal matrix.The latter causes compression and deformation of the coal matrix in the form of pore pressure.Related studies show that the coal continues to expand and deform when non-adsorptive He is injected into the coal (Zhang 2015;Durucan et al. 2009).The root cause is that the gas molecules enter the pores and fractures with a spatial size greater than or equal to the average free path of the gas molecules, resulting in an increase in the volume of the pores and fractures, which is manifested as an expansion deformation of the coal at the macroscopic level.
Thus, the deformation mechanism of coal contains two main types (Lu et al. 2001): (1) Ontogenetic deformation, deformation caused by the coal matrix itself (expansion effect of adsorbed gas on coal and compression effect of free gas on coal).( 2) Structural deformation, deformation resulting from relative displacement between coal matrix (expansion effect of free gas on coal).That is, the gas present in the two states produces three aspects of deformation effect on the coal, as presented in Fig. 11.
Since the ability of coal to adsorb CH 4 is greater than the ability to adsorb N 2 , the reduction in surface-free energy on coal when adsorbing CH 4 is greater than the reduction in surface-free energy on coal when adsorbing N 2 .Under the combined effect of the three stresses (expansion stress of adsorbed CH 4 on coal matrix, compressive stress of free CH 4 on coal matrix, expansion stress of free CH 4 on the micropores and cracks of the coal), the deformation amount of coal when adsorbing CH 4 is greater than the deformation amount of coal when absorbing N 2 .
In addition, coal is a complex heterogeneous medium.The material composition, particle size, and cement make the coal have structural differences.This difference will affect the gas adsorption-desorption, which will affect the deformation of the coal itself in all directions.That is, the adsorption-desorption deformation of coal generally has anisotropic characteristics.

Anisotropy and gas-difference characteristics of coal deformation
To study the anisotropy and gas-difference characteristics of coal deformation, the anisotropy coefficients (β 1 is the ratio of the axial adsorption strain to the circumferential adsorption strain.β 2 is the ratio of the axial desorption strain to the circumferential desorption strain.β 3 is the ratio of the axial residual adsorption strain to the circumferential residual  adsorption strain.)are introduced to analyze the anisotropy characteristics of coal deformation, and the gas-difference coefficients (γ 1 is the ratio of the axial/circumferential strain generated by the adsorption of CH 4 to the axial/circumferential strain generated by the adsorption of N 2 .γ 2 is the ratio of the axial/circumferential strain generated by the desorption of CH 4 to the axial/circumferential strain generated by the desorption of N 2 .γ 3 is the ratio of the axial/circumferential strain produced by the residual CH 4 to the axial/circumferential strain produced by the residual N 2 .)are introduced to analyze the gas-difference characteristics of coal deformation.Taking the experimental duration of 1.80 × 10 3 s as the division basis of the time nodes (T), the adsorption process was divided into eight-time nodes, and the desorption process was divided into five-time nodes.

Time-varying characteristics of coal deformation
The variation pattern of the anisotropy coefficient and gas discrepancy coefficient of coal deformation with experimental time is shown in Fig. 12. Anisotropy coefficient: It can be seen from Figs. 12a, b that β 1 is relatively stable during the CH 4 /N 2 adsorption process.The β 1 when coal adsorbs CH 4 and N 2 is 0.919-1.172and 1.005-1.117,respectively.In the initial stage of CH 4 / N 2 desorption, β 2 decreases slightly.The reason is that after CH 4 /N 2 adsorption equilibrium, the force in the axial direction of the coal is superimposed on the gas equilibrium pressure.After the desorption experiment starts, the gas pressure at the exhaust end is instantly deflated, the axial force is decreased, and the coal first expands in the axial direction.The desorption shrinkage in the axial direction is reduced, resulting in a slight decrease in β 2 .The β 2 tends to increase Gas discrepancy coefficient: It can be seen from Figs. 12c, d that γ 1 is relatively stable during the CH 4 /N 2 adsorption process.The γ 1 of axial strain and circumferential strain of coal are 1.621-2.215and 1.642-1.986,respectively.In the early stage of CH 4 /N 2 desorption, γ 2 decreased slightly.The reason is that after CH 4 /N 2 adsorption equilibrium, the axial force on the coal superimposes the gas equilibrium pressure, and the N 2 equilibrium pressure is greater than the CH 4 equilibrium pressure.After the N 2 desorption experiment started, the axial force on the coal decreased significantly, the expansion ability in the axial direction was strong, and the desorption shrinkage decreased, while the shrinkage ability in the circumferential direction was strong, and the desorption shrinkage increased.As the desorption time prolongs, γ 2 tends to increase.The γ 2 of axial strain and circumferential strain of coal are in the range of 0.738-1.652,0.791-1.794.During the desorption of CH 4 /N 2 from coal, the γ 3 of axial strain tends to increase, while γ 3 of circumferential strain has no obvious change pattern.

Discrete characteristics of coal deformation
From the analysis in Sect.5.2.1, it can be known that the adsorption strain/desorption strain of the columnar coal sample has obvious discrete characteristics.It is necessary to analyze the degree of dispersion in coal strain at each equilibrium pressure during CH 4 and N 2 adsorption/desorption, as illustrated in Fig. 13.
It can be seen from Figs. 13a-d that, (1) Adsorption process: when the CH 4 pressure is ≤ 1.14 MPa, the axial adsorption strain is larger than the circumferential adsorption strain.When the CH 4 pressure is ≥ 1.34 MPa, the axial adsorption strain is smaller than the circumferential adsorption strain.The axial adsorption strain was greater than the circumferential adsorption strain in the experimental N 2 pressure range.It is because the bedding structure of the coal sample is perpendicular to the axial direction of the coal, and the adsorption deformation amount in the vertical bedding direction is stronger, which shows that the axial adsorption strain is larger than the circumferential adsorption strain when the CH 4 /N 2 pressure ≤ 1.14 MPa.With the increase of CH 4 pressure, the amount of gas adsorbed by coal increases, the reduction of surface-free energy increases, and the strength decreases significantly.Moreover, a larger expansion strain is generated in the circumferential direction where the force is smaller, indicating that the axial adsorption strain is smaller than the circumferential adsorption strain when the CH 4 /N 2 pressure ≥ 1.34 MPa.
(2) Desorption process: The total axial desorption strain is generally smaller than the circumferential desorption strain in the CH 4 pressure range, and the axial residual strain is larger than the circumferential residual strain.When the CH 4 pressure is ≤ 1.14 MPa, the change of β 3 is not obvious.When the CH 4 pressure ≥ 1.34 MPa, β 3 shows a gradually decreasing trend.The dispersion of β 2 and β 3 is large during the desorption of N 2 from coal.
It can be seen from Figs. 13e-h that γ 1 > 1 for CH 4 /N 2 adsorption and γ 2 total > 1 and γ 3 > 1 for CH 4 /N 2 desorption by coal.It indicates that the axial strain and circumferential strain generated by the adsorption/desorption of CH 4 in coal are greater than those generated by the adsorption/desorption of N 2 .γ 3 for residual CH 4 /N 2 in coal > γ 1 for adsorption of CH 4 /N 2 > γ 2 for desorption of CH 4 /N 2 at the same time nodes.
In summary, the dispersion of β 1 and γ 1 at each time node during the CH 4 /N 2 adsorption process is large for gas pressures ranging from 0.74 to 1.14 MPa.As the gas pressure increases, the dispersion of β 1 and γ 1 at each time node decreases.During the CH 4 /N 2 desorption process, with the increase of CH 4 pressure, the dispersion of γ 2 remains unchanged while the discreteness of β 3 decreases.With the increasing pressure of N 2 , the dispersion of β 3 and γ 3 has no obvious change rule.

Strain model of coal adsorption-desorption CH 4 /N 2
Coal adsorption/desorption deformation involves coal-gas interaction and the mechanical behavior of gas adsorption/ desorption (Chen et al. 2018;Zhao et al. 2013).From the analysis in Sect.5.1.2,it can be known that the stress in the process of gas adsorption/desorption includes three types.The adsorption/desorption deformation of coal is the result of the coupling effect of three kinds of stress (the gas adsorption deteriorates the mechanical characteristics of coal, resulting in obvious compression deformation of coal.The effect of pore pressure changes its own pore and fracture structure, which in turn affects the amount of gas adsorption and coal deformation.)(Liu et al. 2018;Sun et al. 2023).Simply analyzing the coal deformation caused by three types of stresses separately not only ignores the complex coupling relationship among the three, but also leads to the establishment of a more complicated coal strain model.Therefore, it can be considered to study the comprehensive From the analysis in Sects.4.1 and 4.2, it can be known that the variation law of CH 4 /N 2 adsorption amount with adsorption time and desorption time, as well as the variation law of strain generated by CH 4 /N 2 adsorption on coal with adsorption time and desorption time are consistent with the Langmuir-type equation.To eliminate the effect of time effect, Eq. 1 is substituted into Eq.2. Establish the relationship model between gas adsorption amount and coal adsorption strain in the whole process of CH 4 /N 2 adsorption experiment, and the relationship model between gas adsorption amount and coal desorption strain in the whole process of CH 4 /N 2 desorption experiment, as shown in Eq. ( 3). ( Taking the axial/circumferential adsorption strain and axial/circumferential desorption strain of coal under different CH 4 /N 2 pressures as examples, the applicability and reliability of the coal strain model (Eq.( 3)) were verified.The fitting results of the coal strain model are shown in Fig. 14.
The proposed model has a large error in fitting coal adsorption strain data and a small error in fitting coal desorption strain data.This is because the columnar raw coal has a certain spatial scale, and under the same adsorption time, the deformation degree at each position of the raw coal is different.Since the sticking position of the strain gauge is attached to the middle of the coal sample, the adsorption Fig. 13 Discrete characteristics of coal deformation strain lags behind the gas adsorption amount, and the desorption strain leads the gas adsorption amount.Generally, the coal strain model has a high degree of fit, which can reflect the correlation between gas adsorption amount and coal strain amount in each stage of CH 4 /N 2 adsorption-desorption to some extent.

Applicability of N 2 injection displacement CH 4 technology to low-permeability coal
The applicability of the N 2 injection for CH 4 displacement technology to the gas occurrence characteristics in low-permeability coal seams requires comprehensive consideration of the following three aspects: (1) Displacement effect: Under the same gas pressure, the equilibrium time of coal adsorption/desorption of N 2 is shorter than that of adsorption/desorption of CH 4 (for example, when the gas pressure is 1.14 MPa, the time to reach the equilibrium of CH 4 /N 2 adsorption by coal is 2.600 × 10 4 s, 1.558 × 10 4 s).And the dynamic viscosity coefficient of N 2 is smaller than that of CH 4 , which makes N 2 have a very good carrying effect of CH 4 , thus realizing the increase of CH 4 flow in coal seam (Yang et al. 2016;Ji et al. 2023).
(2) Economic benefits: As an important component of air, N 2 comes from a variety of sources.There are various ways to produce N 2 , the process of N 2 production is mature, and the cost of N 2 production is low.After N 2 is mixed into CH 4 , it is not easy to make it lose its combustion and utilization value, which is beneficial to the utilization of CH 4 resources (Hao et al. 2016).In addition, a reasonable and effective field construction process of N 2 injection for CH 4 replacement should be adopted to increase the CH 4 volume fraction of the mixed gas and reduce the separation and purification costs in the process of the CH 4 utilization process, thereby improving the economic efficiency.(3) Safety issue: Under the same gas pressure, the strain of coal absorbs/desorbs N 2 is smaller than that of absorbs/ desorbs CH 4 (for example: when the gas pressure is 1.14 MPa, the equilibrium strains when coal adsorbs CH 4 /N 2 are 565.95μεand 273.21με.), which makes the outburst danger of N 2 injected into the coal seam weaker than that of CH 4 , and the safety risk of N 2 leakage is small (Lin et al. 2023c).
In summary, N 2 has good injectability in low-permeability coal seams and has the dual function of improving coal seam permeability and enhancing gas flow.N 2 injection for CH 4 displacement technology can not only improve the effect of gas management in low-permeability coal seams but also effectively reduce the cost of gas injection and increase the profit per ton of coal, thus effectively promoting the efficient utilization of coal seam gas resources.

Conclusions
(1) Micropores and transition pores are relatively developed in coal samples, and the pore morphology is mainly semi-open pores.The pore structure is highly complex and heterogeneous.The tortuosity of the coal sample is 5.81, the effective porosity is 3.04%, and the pore connectivity is 40.36%.As the pore-size increases, the proportion of pores in each pore-size segment decreases, and the pore connectivity ratio increases, indicating that the connectivity of the seepage pores is good, and the connectivity of the adsorption pores is poor.
(2) Under the condition of constant triaxial stress, the ability of coal to adsorb CH 4 and its ability to adsorb CH 4 deformation is greater than that of N 2 .The evolution law of strain (axial strain, circumferential strain, volumetric strain) with experimental time for the whole process of CH 4 /N 2 adsorption-desorption by coal can be divided into three stages.The variation pattern of coal strain produced by CH 4 /N 2 adsorption-desorption with the experimental time conforms to the Langmuir-type equation.
(3) The change law of coal strain produced by CH 4 /N 2 adsorption-desorption with the experimental time corresponds to the Langmuir-type equation.The expansion strain of the coal increases exponentially as a function of CH 4 adsorption.The desorption shrinkage strain of coal increases exponentially as a function of CH 4 desorption.(4) The deformation caused by the adsorption-desorption of CH 4 /N 2 in coal has anisotropic and gas-difference.A strain model for the adsorption-desorption of CH 4 /N 2 from coal was established by considering the expansion stress of adsorbed gas on the coal matrix, the compression stress of free gas on the coal matrix, and the expansion stress of free gas on micropore fractures, which effectively reflects the correlation between the process gas adsorption and coal strain amount at each stage of CH 4 /N 2 adsorption-desorption experiment.( 5) N 2 has good injectability in low-permeability coal seams and has the dual functions of improving coal seam permeability and enhancing gas flow, which not only effectively improves the effect of gas management in low-permeability coal seams, but also reduces the cost of gas injection, increases the profit per ton of coal, and promotes the efficient utilization of gas resources.
Coal pore structure characterization experiments include: (1) Low-pressure CO 2 adsorption experiment, low-temperature N 2 adsorption experiment: Determination of micropore and transition pore parameters of coal samples, and the sample specifications are 60-80 mesh coal powder.(2) Highpressure mercury intrusion experiments: To determine the mesopore and macropore parameters of coal samples, and the sample specifications are 3.0-4.0mm coal particles.(3) Low-field NMR experiment: To determine the pore parameters of cylindrical standard coal samples.

Fig. 3
Fig. 3 Multimethod for determination of coal pore structure

Fig. 12
Fig. 12 Time-varying characteristics of coal deformation

Table 1
Basic parameters of the coal samples

Table 3
Fitting parameters of CH 4 /N 2 adsorption amount Note: I represents the adsorption process.II represents the desorption process Gas type Stage Fitting parameter Gas pressure (MPa) Stage Fitting parameter Gas pressure (MPa)

Table 4
Adsorption amount, desorption amount and residual adsorption amount

Table 5
Fitting parameters of axial/circumferential/volumetric strain of coal

Table 6
Fitting parameters for the adsorption-desorption strain of coal

Table 7
Physical parameters of CH 4 /N 2 Fig. 11 Coal deformation characteristics in complex pore