Classification of fires in coal waste dumps based on Landsat, Aster thermal bands and thermal camera in Polish and Ukrainian mining regions

A self-heating intensity index (SHII) based on the highest (pixel max.) and lowest (pixel min.) values taken from satellite thermal maps of burning coal waste dumps are proposed. The index enables the classification of such fires in Ukrainian- and Polish coal waste dumps. Both in Ukraine and in Poland, varying thermal intensities during 1985–2019 are revealed, using the SHII and following thermal intensity threshold values, namely, extreme thermal activity (> 7), advanced (3–7), moderate (3–1.5), initial (1.5–1), no activity (< 1). The SHII shows decreasing thermal activity in the selected Ukrainian coal waste dumps during 2017–2019. It aids in reconstructing the thermal history of the dumps. Analysis of satellite images revealed a large number of burning coal waste dumps in the Donetsk Coal Basin (Ukraine) with high thermal activity. Such burning likely reflects large amounts of organic matter and sulphides in the dumped material subjected to self-heating and self-burning processes, lack of compaction of the coal waste and/or high methane contents. Comparison of SHII values calculated from satellite- and drone thermal-camera images were compared to show that SHII from drone thermal images have much higher values than those from satellite images; the former have better resolution. Thus, SHII from Landsat- and drone images should be used separately in dump heating studies.


Introduction
Coal mining worldwide is associated with the production of waste mostly composed of claystones, mudstones, sandstones, conglomerates, carbonates, carbonaceous shales, and pyrite-bearing carbonaceous rocks. The waste material usually contains 5%-30% of organic matter from very thin, workable or poor-quality uneconomic coal seams, rock partings, and dispersed organic particles (Skar_ zyńska 1995). The waste material begins to weather immediately after deposition due to organic matter oxidation and other processes which, later, may lead to selfheating.
Carbonaceous rocks are usually in thermodynamic equilibrium with their geological environment at depth. This balance is disturbed by their relocation during mining into an oxygen-rich environment. As carbonaceous matter may undergo self-heating at these conditions due to the fact that heat is not adequately dissipated. This occurs independently of pyrite weathering and oxidation. With the participation of thionic bacteria, the pyrite oxidation process can be faster. The oxidation reaction is highly exothermic as the pyrite oxidizes to sulphuric acid. This significantly increases the rate of low-temperature oxidation (Kaymakçı and Didari 2002;Melnikov and Grechanovskaya 2004;Pone et al. 2007;Onifade and Genc 2018). In the initial stages of self-heating subjected for high volatile bituminous coals or sub-bituminous coals, the temperature increases slowly until a threshold temperature Electronic supplementary material The online version of this article (https://doi.org/10.1007/s40789-020-00375-4) contains supplementary material, which is available to authorized users.
& Á dám Nádudvari adam.nadudvari@us.edu.pl of 60-80°C is attained. When that threshold is exceeded, the temperature rises fast and self-ignition and burning of the waste follow. Heating inside a coal waste dump is typically highly variable with temperatures ranging from ambient to [ 500°C. However, at the end stages of heating in the subsurface, self-combustion temperatures can reach up to 1000-1300°C (Carras et al. 1994(Carras et al. , 1999Skar_ zyńska 1995;Heffern and Coates 2004;Querol et al. 2008;Ribeiro et al. 2010;Jendruś 2016). Several factors influence self-heating occurrence and progress. The selfignition temperature is strongly rank-dependent, increasing with increasing rank of the organic matter, i.e., * 150°C for subbituminous coals, * 200°C for bituminous coals and * 300°C for anthracites (Sokol 2005). In general, lower rank coals such as lignites and subbituminous coals are more susceptible to self-heating than higher rank coals (Chandra and Prasad 1990;Bell et al. 2001;Suárez-Ruiz and Crelling 2008;Ribeiro et al. 2010;Vice et al. 2019). However, self-heating occurs in coals and coal waste of all ranks (e.g., Stracher et al. 2010Stracher et al. , 2012Stracher et al. , 2015Stracher 2018). Apart from the organic-matter rank, the susceptibility of coal waste to self-heating is dependent on the number of other factors. Internal factors are the content of organic material, its maceral composition, mineral-matter content and composition, moisture, and oxygen content. External factors are air temperature, wind direction, size and distribution of coal waste particles, and the shape, layer structure, and compaction of a dump (Skar _ zyńska 1995; Saghafi and Carras 1997;Lohrer et al. 2005;Pone et al. 2007;Zhang and Kuenzer 2007;Carras et al. 2009;Masalehdani et al. 2009;Misz-Kennan andFabiańska 2010, 2011). Poor compaction of coal waste, common in the past, allows easier penetration of air and rainwater into the dump, promoting the self-heating process (Bell et al. 2001). For all the above reasons, the heating is very complex. It occurs in coal seams, coal dumps, and coal waste dumps everywhere coal is mined (e.g., Stracher et al. 2010Stracher et al. , 2012Stracher et al. , 2015Stracher 2018). The phenomenon is very dynamic with temperatures fluctuating in any individual place over time. The thermal processes occur under oxygen-limited conditions and commonly without flames (Misz-Kennan 2010;Misz-Kennan and Tabor 2015).
In Poland and Ukraine, coal waste dumps are often surrounded by settlements (Fig. 1). They are used as meeting places, touristic viewpoints, sites for cultural exhibitions, and sport events, including climbing, cycling and extreme sports (Ivchenko and Lebezova 2012). Dump emissions adversely affect human-and animal life. Emitted dust damages the central nervous and circulatory systems, kidneys, livers, and contributes to the development of cancer (Glushkov et al. 2010;Petrov et al. 2014;Privalov 2015). Apart from this permanent influence, large disasters such as explosions can occur during dump exploitation as e.g., in case of the coal waste in the Dymytrov town (now Myrnohrad) in 1966 in Donbas area. Part of the dump torned appart and the burning material slumped on to the Nakhalovka settlement (Skrypnik and Tretyakova 2015). Witnesses compared this event to a volcanic eruption. Several similar accidents have occurred in the Donetsk Coal Basin (Gayvoronsiy and Yugov 2015).
Due to its adverse impact on the environment and health, it is important to detect the self-heating process as early as possible using satellite remote sensing and drones to prevent spreading of self-heating affected areas and to extinguish zones subjected to self-combustion. Hot spots in self-heated coal waste are commonly located 2-3 m below the surface. They usually appear as high-temperature surface anomalies, which can be detected by Thermal Infrared Sensors (TIRs) used by Landsat 4-5 TM (120 m resolution resampled to 30 m), 7 ETM? (60 m resolution resampled to 30 m), 8 OLI (100 m resolution resampled to 30 m), and ASTER (90 m, resampled to 30 m) satellite images or by Thermal Infrared Cameras (details of satellite images in Table 1S in the Supplementary Material). Typically the migration, intensification, and disappearance of such hot spots can be recognized on thermal maps (Nádudvari 2014).
The aim of the research is to create a classification index for self-heating intensity in coal waste dumps in different regions using Landsat-, ASTER-and thermal-infrared camera acquisition from a drone using Landsat 4-5 TM, ETM?, and ASTER images. The other aim is to use this index to compare the self-heating intensity of burning dumps from different coal basins and provide a reconstruction of the thermal history of coal waste dumps. As, in most cases, there are no records of dump history, such a method could help better understand the initiation, development, migration, and waning of dump heating.

The scope of investigation
For the present studies, 35 coal waste dumps in Ukraine and 14 in Poland were selected. The coal waste dumps represent the mined coal-rank types except for their lower carbon content.

Coal waste dumps in Ukraine
Most (\ 95%) of Ukrainian hard-coal deposits are located in the Donetsk Coal Basin spreading over Donetsk, Lugansk, and Dnipropetrovsk. The coal is generally of anthracite (2.5%-3.5% random vitrinite reflectance R r ) and meta-anthracite ([ 3.5% R r ) rank in the central part of the basin. Bituminous coals (0.6%-2.5% R r ) are concentrated on the western-and northern basin margins (Levenshtein Fig. 1 The location of the study area with detected self-heating coal waste dumps in Ukrainian and Polish coal mining regions. The Landsat, ASTER images were downloaded from https://earthexplorer.usgs.gov/ website. Not all coal waste dumps are indicated in Poland, just the thermally active dumps in 29.01.2019. The location (coordinates) of all dumps see in Table 1 Classification of fires in coal waste dumps based on Landsat, Aster thermal bands and thermal… 443 et al. 1991;U.S. EPA 2002;Savitsky 2015 (Sachsenhofer et al. 2003;Antsiferov et al. 2004;Privalov et al. 2007;Sachsenhofer et al. 2012;Dychkovskyi et al. 2014;Savitsky 2015). The coal waste generated during exploitation and beneficiation is deposited in about 1200 stockpiles containing * 1.5 billion m 3 of coal waste and \ 120 million tons of waste are produced annually by coal preparation plants (Fig. 1). The waste material consists of argillites, siltstones, limestone rocks, sandstone, coal, and mineral pyrite aggregates showing various degrees of metamorphism (Kochetov and Konischeva 1994;Omelchenko 2011;Voloshyna et al. 2014). It is estimated that the Donbas coal waste dumps may contain 10%-46% of organic matter, \ 20% of silica and iron oxides. As the Ukrainian coal deposits have high (1.5%-5.5%) sulphide contents, the waste dumps are also rich in sulphides (Vasileva 2015;Perov et al. 2016).
The coal wastes in Ukraine were not properly compacted, which accentuates water erosion, especially on conical dumps. Significant annual temperature amplitudes promotes the fragmentation of coal waste particles (Vasileva 2015). As the material is typically loose, gravel-and stony fractions predominate. Even on the oldest dumps, fractions \ 1 mm rarely exceed 30% (Torokhova 2007). The coarseness will result in greater oxygen availability which, combined with a large amount of organic material, will promote self-heating.
These dumps located in the Donetsk Coal Basin annually emit [ 500,000 tons of harmful gases into the atmosphere (Kochetov and Konischeva 1994;Omelchenko 2011). Each year, from the surface of a single dump, * 400 t of dust is generated and * 8 t of salt is washed out (Kuzyk 2009). It is estimated that 15,000 t of CO 2 and \ 5000 of CO are emitted annually. Other environmental issues linked to coal mining in the Donetsk Coal Basin are water supply disruptions, increased salinity of groundwater and enormous accumulations of solid waste, resulting in land degradation, air pollution and dust, as well as mudslides (Savitsky 2015). Coal production declined during the 1990s due mainly to the collapse of domestic demand and the plant closures in heavy industry. Between 1990 and 2004 there were 119 underground coal mines abandoned without remediation or in the process of mine closure. In addition, * 77% of abandoned mines in the region reported elevated methane contents released from coal (U.S. EPA 2002; Privalov et al. 2004;Oprisan 2011;Savitsky 2015).

Coal waste dumps in Poland
In Poland, self-heating in coal waste occurs in two mining areas, i.e., the Upper Silesian Coal Basin (USCB) and the Lower Silesian Coal Basin (LSCB). The * 7400 km 2 USCB is the largest coal basin in Poland and one of the largest in Europe (Jureczka and Kotas 1995;Kędzior 2009). Coal seams are generally thin (\ 1-1.5 m). About 60 seams are typically 4-8 m thick but can reach up to 24 m (Fabiańska et al. 2013b). The coals are hard coals varying in rank from subbituminous to high-volatile bituminous coals that are mostly humic, rarely sapropelic. In their composition, vitrinite-group macerals predominate ([ 80%). Their content is lowest in the eastern part of the basin and increases westwards. The coal rank in the western part of the basin is much higher (R r [ 1.0%) than in the eastern part (R r & 0.50%) (Gabzdyl 1994;Jureczka and Kotas 1995;Kotarba et al. 2002;Fabiańska et al. 2013b). Coal waste deposited in the Upper Silesian Coal Basin comprises claystones, mudstones, sandstones, and smaller amounts of conglomerates and carbonates. The organic matter content is commonly 7%-15%, but it may exceed 30% (Skar_ zyńska 1995). Sulphide contents in the coals range from 0.32% to 2.82% (Sobczyk et al. 2016). This, and pyrite (\ 8% content) mixed with coal gangue, has generated favorable conditions for long-lasting coal waste fire that remains hard to control (Jendruś 2017).
Self-heating intensity and its frequency vary considerably within the Upper Silesian Coal Basin. The area most definitely affected by heating is the Rybnik Region in the south-western part of the basin, where almost all coal waste dumps were or are undergoing self-heating ( Fig. 1; coal waste dumps Nos. 5, 6, 10, 12-14). In the western part, where rank is higher than in the eastern, self-heating is more frequent. In the eastern part, self-heating temperatures can be extremely high, e.g., 1300°C as registered in the Szarlota dump near Rydułtowy town, where thermal processes affect large parts of the dump (Fig. 1;dump No. 12;Misz-Kennan 2010;Misz-Kennan and Fabiańska 2010;Misz-Kennan and Tabor 2015). In the northern part of the basin occupied by the highly populated cities of Bytom, Ruda Ś ląska, and Katowice, tens of dumps show lower intensities of heating than those in the Rybnik Region (Misz-Kennan and Tabor 2015). However, self-heating is common there and difficult to extinguish. Heating is least intense in the eastern part of the basin.
This regional pattern of heating in the Upper Silesian Coal Basin is explained by differences in the rank of organic matter within the waste rocks. Average present-day geological temperatures within the Mudstone Series in this basin ranging from 24.9°C (eastern part) to 58.9°C (westsouthern part) approximately coincide with the pattern of mean random vitrinite reflectance (Karwasiecka 2001;Kędzior 2015). These temperature differences reflect the geological history of the basin (Kędzior et al. 2007;Kędzior 2015). It is not surprising that organic matter in coal waste shows a similar pattern of thermal maturity. A higher coalification stage means higher self-heating intensities in the dumps. Moreover, the sapropelic coals deposited there are highly reactive.
In the smaller 350 km 2 Lower Silesian Coal Basin, hardcoal seams cover an area of * 350 km 2 . Large quantities of natural gas (mainly CO 2 and CH 4 ) constitute a CH 4 explosion hazard. The quality of the coals varies considerably; in the Wałbrzych area, the coal R r ranges from 1.10% to 4.28%, in the Nowa Ruda area from 1.08% to 1.56% (Bossowski 1995;Kotarba and Rice 2001).
In this basin, three dumps were subjected to self-heating during the period 1987-2017, namely, Wałbrzyc, Słupiec, and Nowa Ruda ( Except for sulphide contents, there is no significant difference between Ukrainian-and Polish coal deposits in terms of coal quality, i.e., gross heating values and remaining ash contents (U.S. EPA 2013; Małkowski and Tymoshenko 2018).

Methodology
For this study, 35 representative coal waste dumps with different shapes, e.g., conical and trapezoidal from the Donetsk Coal Basin in Ukraine from 1985 to 2019 (dates of acquired data in Table 1S) were selected. For comparison, 14 coal waste dumps from the Upper-and Lower Silesian Coal Basins between 1985 and 2018 were also selected (Table 1S; Fig. 1; Table 1).

Application of Landsat images for detecting selfheating dumps
Using the Thermal Infrared (TIR) sensors of satellite images, i.e., Landsat series, ASTER is the cost-effective and time-saving technique for monitoring coal waste fires and detecting their thermal anomalies. Several authors have successfully applied Landsat, ASTER night-time and winter-time images for localizing such coal-or coal-seam fires worldwide (e.g., Voigt et al. 2004;Gangopadhyay et al. 2005;Chatterjee 2006;Zhang and Kuenzer 2007;Prakash et al. 2011;Guha and Kumar 2012). The image data were obtained from night-time and snow-covered images with zero cloud-, haze-and fog cover from https:// earthexplorer.usgs.gov (2019). The calculations were performed according to the methodology given in https:// www.usgs.gov/land-resources/nli/landsat/using-usgs-land sat-level-1-data-product (2019). First, the radiance was calculated and then the brightness temperature was converted from Kelvin to Celsius according to T Celsius-= T Kelvin -273.15 (TS: temperature at satellite). To obtain the Land Surface Temperature (LST), a thermal emissivity map first had to be generated based on the spectral absorption properties of the surface materials as surface temperatures are directly related to surface physical properties. Firstly, where NDVI min and NDVI max = minimum and maximum values of the NDVI (Normalised Difference Vegetation Index) image. This helped to separate the surface materials.
All calculations were performed in ENVI 5.3 software. The self-heating intensity was calculated from the highest (pixel max) and lowest (pixel min) values according to: For the index, the required pixel values were taken from the area of a coal waste dump, taking care to avoid any man-made structures, lakes, or ponds during delineation. These ratios should be used only for night-time images with cold weather (* \10-15°C), and daytime snow-covered images. The ratio values increase when thermal activity is high.
Differences in albedo and features such as slope and aspect can significantly impact the thermal anomalies. Hot spots of low thermal activity are usually visible on Landsat thermal map with 2-3°C difference between pixel max (hot spot)-pixel min (cold snow covered surface with no thermal activity). Also hot surfaces on burning dumps with small extensions (the area of a hot spot is smaller than the satellite sensor of TIR) are difficult to detect and distinguish from the surrounding pixel values. Furthermore these pixel values are also disturbed by the sun effect (same for the thermal camera images). However the thermal camera images are more sensitive for the sun influence. Therefore, any disregard for the manner of the impact of solar radiation on the surface can lead to significant distortion of thermal information from a surface. Even partial sunshine significantly disturbs the temperature values obtained (Zhang and Kuenzer 2007;Nádudvari 2014;Usamentiaga et al. 2014;Nádudvari and Ciesielczuk 2018).

Thermal images taken by a drone
Infrared low-altitude aerial photogrammetry is currently one of the most popular methods for thermal-data collection (Sawicki 2012;Usamentiaga et al. 2014;Wasilewski and Skotniczy 2015). The current state of the technology allows acquisition of data with very good resolution; their accuracy is already measured in centimeters-much better than the TIR sensors of satellite images (Landsat series, ASTER). Unfortunately, there are a number of limitations. First of all, weather requirements strictly include no rain or fog, clean air, no wind, stable air temperature and full cloud cover (Bernard et al. 2014). The omission of any of the requirements significantly affects the accuracy and reliability of the thermal data.
Appropriate planning of a drone flight and the fieldwork requires much more time than is expended using one of the satellite databases at a desk. Moreover, the data obtained are usually difficult to compare with the historical state of a dump. As high-resolution thermal drone photographs became popular only in the last decade, archival data are not available. Unfortunately, there are currently no openaccess databases collecting thermal images from drones The method presented here is based on two thermal maps made using the DJI S900 drone with a FLIR Vue Pro R336 thermal imaging camera (matric 336 9 256, lens 9 mm, spectral range 7.5-13.5 lm). The maps cover the area of the burning coal waste dump in Ruda Ś ląska ( Table 1, No. 11). The first flight performed in March 2018 (479 thermal images) was treated as a trial. Thus, its range was limited to fire spots visible on the surface. Unfortunately, the final image shows that the range was too small to fully cover all burning zones and sites. The second flight was in October 2018, when 650 thermal images were taken that represent the variability of the fire over a period of 7 months. The second flight was based on the first flight. The range of the flight was extended to include fragments missed earlier in the western part of the dump.
To eliminate the influence of insolation on temperature measurements, all the photographs were taken just before sunrise, in conditions close to the benchmark. The air temperature during the flights was -2°C (March 2018) and ? 9°C (October 2018). Drone flights were carried out at a height of 70 m. The final resolution of the thermal maps is 20 cm.
In preparation of a large-scale thermal map, it is necessary to make a whole series of photographs with appropriate transverse (minimum 50%) and longitudinal coverage (minimum 70%). Apart from the images, the data from the GPS receiver placed on the drone was also collected. This gives information on the exact location of each photograph and allows for subsequent georeferencing of every individual image. The next step was to create a mosaic using the AgiSoft PhotoScan software. Appropriate algorithms were used to search for the same points on every individual image in order to combine the images (Maes et al. 2017). Five ground control points with known coordinates were added. These were later used to register and georeference the image. Finally, the picture locations were optimized and the map created.

Results and discussion
In * 330 self-heating coal waste dumps in the Donetsk Coal Basin, compared to * 10 in Upper-and Lower Silesia, the size and heat intensity of the hot spots could be detected on satellite images in 2017 (Fig. 1). The estimated number of burning dumps is between 140 and 400. The exact number is unknown as fires in these dumps are activating and extinguishing continuously (Kochetov and Konischeva 1994;Omelchenko 2011;Voloshyna et al. 2014). Self-heating events are still a problem in the Upper Silesian Coal Basin. In 2000-2010, at least 21 fire occurrences were observed in original-and recultivated dumps. Between 2007 and 2013, 15 thermally active dumps were reported from among the 220 coal waste dumps in the Upper Silesian Coal Basin (Misz-Kennan and Fabianska 2010; Misz-Kennan 2010; Skręt et al. 2010;Zając and Zarzycki 2013;Fabiańska et al. 2013a). In the Lower Silesian Coal Basin, the self-heating problems with dumps are generally decreasing (Fabiańska et al. 2019).
Using the proposed SHII, the results indicated varying thermal activity on the studied Ukrainian dumps between 1985 and 2019 (Fig. 2a-c). The results helped to establish SHII threshold values, i.e., extreme ([ 7), advanced (3-7), moderate (3-1.5), weak or waning (1.5-1), no thermal activity (\ 1). During 2017-2019, compared to earlier periods, the thermal activity of major dumps could be seen to have changed, e.g., to a moderate-from an advanced state of self-heating or to have extinguished. However, 20-30 years ago, extreme thermal intensities were recorded in e.g. , 1987, 2002 and 2003. Usually it happens when a coal waste dump is excavated for recover remaining coal particles as it has happened in Ukraine in 2000 years, see and example on Fig. 3-Makoszowy dump (Pilov et al. 2000). There is no difference in the pattern of heat intensities between the Polish and Ukrainian self-heating dumps (Fig. 2d).
The studied dumps in the Upper Silesian Coal Basin can also attain extreme self-heating conditions (Fig. 3). Typically, intensive self-heating on the surface can start, when a dump with ongoing burning inside is opened by excavation. That is perfectly seen in the diagram (Fig. 3) for the Makoszowy dump, where coal waste excavation started in early 2000 and thermal activity stopped by about 2007. By 2013, all coal waste had been removed from Makoszowy dump (Nádudvari and Ciesielczuk 2018). A similar tendency is visible on a representative dump (Fig. 3-Ukrainian dump) from the Donetsk Coal Basin for the 2001-2003 timespan, where self-heating progressed from the initial/weak stage to the advanced stage in 1987-1994. The dump was probably opened for excavation or the selfheating spontaneously intensified. Such time-line diagrams can help to visualize the self-heating history of a dump.
In Fig. 4, the highest SHII values among the studied coal waste dumps (02.03.2003-Ukrainian coal waste dump No. 2, intensity 13.8) is shown. Also, the location of the lowest and highest temperatures used for the calculation of the self-heating intensity is also shown. The disadvantage of using different types of a satellite image with the different resolutions is illustrated by another coal waste dump (Polish dump No. 11; Fig. 4). The self-heating intensity is low (1.1-1.3) for both Landsat 8 OLI and for the hot spot perfectly identified with a better resolution at Landsat 7 ETM?; in this case, the index value (2.5) indicates moderate thermal activity. A heated spot on a dump usually shows a [ 3°C difference between the surfaceand air temperatures. However, hot spots are commonly located 1.5-2.5 m below the dump surface with no surface indication of the presence of intensely hot zones even within a few meters of the dump surface (Urbański 1983;Walker 1999;Barosz 2002;Tabor 2002;Day et al. 2015;Jendruś 2017). That makes the detection of hot spots with low intensity or situated in a deeper part of a dump complicated (Figs. 4 and 5). When hot spots occur at shallow depths or with low thermal activity and a limited extent, cold air temperatures can overcome the self-heating and any thermal response by the TIR sensor is diminished (Nádudvari and Ciesielczuk 2018). Therefore, on the drone TIR reacts in the same way. The self-heating spot is completely absent in Fig. 4 (Polish coal waste dump No. 10) as Landsat 8 OLI was unable to properly detect the hot spot; the exception was Landsat 7 ETM?, which seems to be the most effective sensor for such purposes. In Fig. 5, a thermal camera image and a Landsat 7 ETM? image of Polish coal waste dump no. 11 are compared. The SHII was calculated for each pixel and classified according to Fig. 2. The values are corresponding to moderate self-heating stage on the dump. The SHII was calculated for the thermal-camera image. With increasing resolution, the index value also increases because of the better resolution of drone images. Therefore, SHII should be applied, and trends described separately, for Landsat and drone images. The dump was established in 1992 on the site of the former Bielszowice brickworks. Waste material from the nearby Wawel coal mine was delivered there for the duration of 8 years. Gradually, vegetation was introduced onto the surface of the stored material to provide a recreational area. Unfortunately, the content of organic matter was so high that the waste material started to burn in 1995 (Laczny et al. Laczny et al. 2012a, b). Initially, heating involved only a small area in the southwestern part of the dump. Over the years, the fire has spread and migrated north-eastwards. In the 2010s, fire sites also appeared in the eastern part of the dump along the technical road. In the following years, slow migration and The application of the thermal bands of a Landsat image to coal-seam fires can cause problems, when the surface temperatures are extremely high. Usually, such fires have extended surface temperatures of 150-250°C, or even higher, and emit more heat than a simple self-heating site on a coal waste dump (Cracknell and Mansor 1992;Chatterjee 2006;Huo et al. 2014). For example, a 30-cmlong crack emitting hot 400°C gasses from a coal-seam fire might only raise the overall temperature of the 60 m9 60 m (Landsat 7 ETM?) thermal pixel by 3-10°C Fig. 5 Comparison of thermal data from Landsat 7 ETM? and thermal camera mounted on a drone. Also the SHII distribution was calculated from Landsat 7 ETM? using the Eq. (5) just replacing the pixel max. value with the raster image Classification of fires in coal waste dumps based on Landsat, Aster thermal bands and thermal… 451 against the background (Prakash and Gupta 1998;Prakash et al. 1995;Saraf et al. 1995;Zhang et al. 2004). The sensitivity of the thermal band (thermal infrared (TIR)) sensor of Landsat images is a maximum of 70-110°C surfaces, occupying the major part of the pixel area. In the case of extreme coal waste fires, where high-temperature zones at the surface appear with mean temperatures of C 50°C, generally unaffected by air temperature or by the background temperature of the pixel, Landsat TIR bands are not effective (Chatterjee 2006). The short-wavelength infrared (SWIR) Landsat bands 5-7 can detect 160-277°C hot spots, \ 420°C in the case of coal-seam fires, using nighttime images to avoid solar radiation (Rothery et al. 1992;Chatterjee 2006;Huo et al. 2014 The surface temperatures at thermally-inactive sites are lower than the hot-spot temperatures by 6-14°C, on average, or even more depending on the heat intensity (Prakash et al. 2011;Nádudvari 2014;Abramowicz and Chybiorz 2019). Usually, in parts of dumps not affected by fire, ground-and air temperatures should be similar (Jendruś 2017; Abramowicz and Chybiorz 2019). The classification of coal waste fires proposed by Jendruś (2017) is based on the CO content in gases and the difference between the surface temperature of a dump and the surrounding temperature. Self-heating is deemed weak at most, if the difference between air-and surface temperatures is 0 B 3°C, slight if 3 B 10°C, moderate if 10 B 20°C and advanced if C 20°C. On thermally-inactive dumps, surface temperatures can exceed 3°C due to intensive sunlight.
With regard to the SHII, the detected fire was classified as weak, or extinct (or a sun effect), where the difference between the highest and lowest surface temperatures was 3°C. However, where such a difference occurred, where surface temperatures were C 10°C, the index classified the hot spot as an advanced-or extreme self-heating event according to the proposed SHII (Fig. 4). The proposed classification of Jendruś (2017) is based on time-consuming in situ measurements. However, for precise monitoring of hot spots below the resolution of Landsat images, the application of TIR satellite images can cover a wide range of dumps at one time and is effective for larger hot spots.

Conclusions
Especially in Ukraine, a large number of burning coal waste dumps pose a serious environmental-pollution threat. These dumps are not adequately compacted and contain high contents of sulphide as coals in the Donetsk Basin are sulphide-rich. They also comprise high levels of organic matter (10%-46%) and retain methane in elevated quantity; the Donetsk Basin is among the most gas-rich basins in the world. In the waste, the later serves as fuel for long term self-heating and smoldering (Nádudvari et al. 2020).
A large number of fires in the Donetsk Coal Basin reflect the nature of the waste deposited and the mode of storage.
Burning of various thermal intensities occurs in the coal waste dumps of both the Donetsk-and Silesian Basins Basins, especially in the former. A self-heating intensity index (SHII) classifying the thermal intensities of the dumps as extreme, advanced, moderate, weak or inactive helps to detect, monitor, and reconstruct the thermal history of the dumps. The proposed SHII classification may serve as a useful tool for monitoring of ongoing self-heating processes in active and abandoned coal waste dumps. The proposed SHII can be applied worldwide, wherever snowcovered or night-time Landsat, ASTER images are available.
For the difficult-to-detect self-heating areas of the small spatial extent or with low thermal activity at surface, a sensor resolution is important. Although, images from a thermal camera on a drone provide higher resolution images and, thus more detailed information of the location of hot spots in a dump, the long-termed thermal history and burning dynamics can be only discerned from satellite images.
Acknowledgements The authors are grateful to Dr. Pádhraig Kennan (University College, Dublin, Ireland) for assistance in improving the language quality.
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons. org/licenses/by/4.0/.