Potential and properties of marine microalgae Nannochloropsis oculata as biomass fuel feedstock

Microalgal biomass is the most promising and attractive alternative to replace the terrestrial crop utilization for renewable biomass fuel feedstock. The potential for biomass fuel is due to its fast growth rate and high ability for CO2 fixation as compared to terrestrial vegetation. There are many species in the globe, growing both in marine and freshwater. In this work, the marine microalgae Nannochloropsis oculata (N. oculata) had been investigated in terms of potential abundance and physicochemical properties, which determine its feasibility as biomass fuel feedstock. The chemical composition was evaluated by energy-dispersive X-ray spectrometry, and the proximate analysis was done by performing experiments in the thermal gravimetric analyzer. During 7 days of cultivation, the average rate of increase in algal biomass was about 1.5 × 106 cells/ml/day. The proximate analysis of N. oculata indicated that it had compositions of low moisture content and fixed carbon, whereas high volatile matter and ash content, i.e., 3.99, 8.08, 67.45, and 24.47 %, respectively. The energy content, which was calculated through the proximate analysis results, was 16.80 MJ/kg. The algal biomass and its residue after 1,200 °C were characterized by Fourier transform infrared spectroscopy to investigate their chemical macromolecular compounds. This present study concludes that N. oculata is feasible as biomass fuel feedstock, either to direct or co-combustion mode by giving special attention to high ash content.


Introduction
Since fossil fuel sources across the globe are fast depleting, renewable and non-conventional energy sources are urgent to explore to ensure the world is not threatened by a vacuum of energy. Biomass is generally defined as any hydrocarbon material, mainly consists of carbon, hydrogen, oxygen, and nitrogen [1]. It has been recognized as a major world renewable energy source to supplement declining fossil fuel resources [2]. However, the use of first-generation biofuels, which have been mostly taken from food and oil crops, such as rapeseed oil, sugar cane, sugar beet, maize, vegetable oils, and animal fats [3], has generated a lot of controversies, primarily because of their impact on global food markets and food security [4]. Hence, it drives the need to base non-food biomass resource biofuels. As a result, interests in aquatic biomass as the feasible fuel source have recently gained prominence. One of the potential aquatic biomass for fuel is microalgae.
Microalgae will be potential as an important energy source in the future due to their potentially abundant, renewable, and CO 2 neutral fuel [5]. Compared with wood and land crops, microalgae are able to reproduce their biomass very rapidly and are very rich of oil content. Biomass productivity of microalgae can be 50 times more than that of the fastest growing terrestrial plant, namely switch grass [6]. Microalgae multiply their biomass about 1-3 per day [7] and theoretically can produce oil per hectare 100 times higher than that of terrestrial crops [8]. In the appropriate culture media, some algae can achieve very high lipid content, such as Chlorella emersonii [9], Neochloris oleabundans [10], and Scenedesmus abundans [11], which their lipid content up to 63, 56, and 67 %, by dry weight, respectively. Microalgae consume 2 g of CO 2 to produce 1 g of biomass when considering the glucose conversion into starch or lipids. Thus, by assuming a growth rate of 50 g/m 2 /day, it is possible for one hectare pond algae to absorb up to one ton of CO 2 per day [12]. Thereby, microalgae cultures will neutralize CO 2 from their combustion.
Beyond the potential of microalgae for fuel in the future mentioned above, harnessing energy from microalgae must be considered in full transparence of physical and chemical properties. These properties are essential parameters for biomass fuel feedstock because they will affect both their combustion characteristics and proper handling modes in the furnace. The moisture content is very important property affecting the burning characteristics of biomass [13], mainly owing to its necessary of energy for releasing before a combustion process takes place. Hence, it will reduce the temperature in the combustion chamber. To ensure the sustained combustion process, this parameter must be exactly well known. Volatile matter content has also been indicated to affect the thermal behavior of solid fuels. The rate of volatile releases and its quantity determine the flame ignition, stability, and temperature profile in the radiation part of the furnace. Chemical properties of biomass are also a critical parameter as they determine the amount of energy contained in biomass. Likewise, the presence of the inorganic component in the biomass influence in the formation of ash, slag deposits, corrosion of boiler components, and aerosol [14]. Generally the inorganic constituents of biomass are Si, Ca, K, Na, Mg, S, P, Fe, Mn, and Al [15,16], and the concentration of each element in biomass varies in accordance with the kind of species and growing environment. During combustion processes, part of the ash-forming compounds in the biomass mainly alkali metals and chlorine are volatilized into a gas phase, such as HCl(g), KCl(g), (KCl) 2 (g), K 2 SO 4 (g), KOH(g), K(g), Na 2 SO 4 (g), and NaCl(g) [17,18]. As cooling proceeds in the heat exchanger section of boilers, subsequent nucleation or condensation lead to the gases, together with solid phase submicron particles released from the fuel bed, form a large part of the fine ash particles. Otherwise, the compounds composed of Mg, Ca, Fe, Al, and non-metallic elements such as S, P, and Si are relatively more stable and less volatilized [19]. The fractions of non-volatilized compounds are remaining in the charcoal, and through a process of coalescence or melting form ash particles with a variety of shapes, sizes, and compositions, parallel to the characteristics of the parent material [20]. Therefore, to make biomass thermal conversion processes effective, these parameters must be clearly studied.
This work aimed to provide fundamental information for biomass fuel feedstock of N. oculata by investigating the biomass growth in the culture medium and its properties which affect the performance of biomass fuel including the calorific value, moisture content and physicochemical properties. The Fourier transform infrared (FTIR) spectroscopy analysis of both biomass and its residue were also conducted to identify the cellular macromolecular content.

The description of species
N. oculata is a species of a genus Nannochloropsis. It is a unicellular small green alga, found in both marine and freshwater [21,22]. This alga is characterized by spherical or slightly ovoid cells [23] with a diameter of 2-5 lm [24] and absence of chlorophyll b and cellular xanthophyll pigment [25][26][27]. There is one chloroplast in each cell, without pyrenoid. Chloroplast endoplasmic reticulum is continuous with the nuclear envelope. Inside the chloroplast are lamellae, consisting of three thylakoids for each. Only one chlorophyll is present, namely chlorophyll a and the main pigment is violaxanthin. Its cell walls are composed of two components, the fibrillar component and the amorphous component. Fibrillar part forms the skeleton of the wall, which is embedded in the matrix of amorphous component. The most common fibrillar component is cellulose, a polymer of 1,4 linked b-D-glucose. An amorphous mucilaginous material is arranged from proteins, lipids, and polysaccharides. Occasionally, silica, calcium carbonate, or sporopollenin is also present as encrusting substances [28].
Nannochloropsis is widely distributed in oceans worldwide. It plays significant roles in the global carbon and mineral cycles [29]. This microalgae contains rich proteins, pigments, and polyunsaturated fatty acids [26,30,31], and it is commonly used in aquaculture as feed [32,33]. In recent years, Nannochloropsis has been proposed as an excellent candidate for biofuel production [34,35].

Microorganism and culture conditions
The N. oculata strain was obtained from the Institute of Brackish Water Aquaculture (BBAP) Situbondo, East Java, Indonesia. This species was cultured in an open pond with seawater medium in which its salinity and pH were 34 % and 8.6, respectively. The culture medium was enriched with fertilizers whose composition was presented in Table 1. The use of fertilizers was 1 ml/l of the cultivation medium. The cultivation had been performed for 7 days.

Growth evaluation
The biomass productivity of N. oculata was evaluated daily by means of counting the number of cells in the culture medium using hemocytometer and optical microscope (CH2 Olympus optical Co. Ltd, Tokyo, Japan). Measurement was carried out every day at 11:00 AM during the cultivation period. Each measurement was repeated 3 times and the results were averaged.
The N. oculata specific growth rate, which was the change of the natural log of the cell number density (C n ) with time (t), was calculated from the slope of the linear regression of time (days) and cell density (cells/ml) [36]: where C t is cell density at time (t), and C o is cell density at the start of the exponential phase (t o ). The time required to double the cell of N. oculata, termed the doubling time (day), could be estimated by equation: Harvesting and drying The biomass was harvested by precipitating it with caustic soda (NaOH); then it was filtered and washed twice with distilled water. Subsequently, the biomass sediment was dried in an oven at 80°C for 24 h. The dried microalgae chunks were pulverized by the mortar to be fine particles and then finally stored in desiccators.

Chemical composition
Energy-dispersive X-ray (EDX) spectrometry was used to determine the chemical composition of algal biomass. Scanning electron microscope images were taken by FEI Inspect S50 equipped with X-ray microanalysis capabilities (AMETEK EDAX TSL ). Samples were gold coated to minimize the effect of electron charging of the surface, which could distort the images.

Lipid extraction
The total lipid of N. oculata was extracted using a Soxhlet extractor system. Approximately 3 g of biomass powder was weighed into a cellulose thimble inside the extraction chamber. A total of 150 ml pure n-hexane was used to extract the lipid for 6 h at the rate of 10 refluxes per hour to achieve maximum extraction efficiency. The extracted lipid was measured after removing the solvent using vacuum rotary evaporator to evaporate the n-hexane at 35°C for 60 min, and then lipid content was calculated. The adopted Soxhlet unit description could be found in different literature [37].

Proximate analysis
The moisture, volatile matter, fixed carbon, and ash content of the dry algal biomass were determined by thermal gravimetric analyzer (STA PT1600 by Linseis). The adopted method is basically described by Beamish [38] and Mayoral et al. [39]. Approximately 20 mg samples were loaded into an Al 2 O 3 ceramic crucible. Initially, the sample was kept isothermally at 25°C for 8 min. The heating ramp was set at 50°C/min, from 25°C up to 125°C then held for 3 min. A new 80°C/min heating ramp was programmed up to 950°C and maintained at that temperature for a total duration of 40 min. The whole process was done using Argon as purge gas to guarantee a non-oxidative environment. However, this gas was then switched to the air atmosphere when it was achieved isothermally at 40 min. Once a constant mass loss was reached, the isothermally final temperature was maintained for a total duration of 65 min in the air atmosphere to complete the combustion process. The moisture, volatile matter, fixed carbon, and ash were calculated by the difference from slope to slope of thermogravimetric (TG) curve.

Determination of higher heating value (HHV)
The heating value of microalgal biomass was evaluated by an equation proposed by Nhuchhen and Abdul Salam [40]. This calculation was based on values resulted from the proximate analysis.
where, VM, FC, and A were volatile matter, fixed carbon, and ash content of biomass, respectively, by dry weight basis.

FTIR analysis
The infrared spectrum of dried algal biomass and its residue were recorded by Shimadzu FTIR spectroscopy. Both kinds of samples were mixed with potassium bromide (KBr) powder, and then pressed into tablets before measurement. Samples were scanned from 400 to 4,000/cm.

Results and discussion
One of microalgae potential's benchmarks as biomass fuel feedstock is determined by the abundance of the biomass so the availability will be assured. Therefore, the biomass productivity of algae in terms of growth rate is one of the most significant parameters that must be examined. The biomass yields of N. oculata during 7-day cultivation period were depicted in Fig. 1. These results showed that N. oculata multiplied its biomass rapidly, starting at around 2 9 10 6 cells/ml on day 1 to approximately 12 9 10 6 cells/ml on day 7. It meant the average increase in biomass was approximately 1.5 9 10 6 cells/ml/day, higher than that of Selenastrum sp., which increase in cell number per day was about 1.6 9 10 4 up to 2.2 9 10 4 cells/ ml/day [41]. If the productivity of N. oculata was expressed in growth kinetics, then it had specific growth rate of 0.27/day and doubling time of 2.59 days as shown in Table 2. Its growth kinetics revealed that N. oculata biomass productivity was higher than Dunaliella salina [42], S. obliquus [43], and C. vulgaris [44], which their growth rates were 0.18, 0.22, and 0.14/day, and their doubling time were 3.85, 3.15, and 4.95 days, respectively. This result was important to note by considering the N. oculata had been cultivated in the traditionally natural open pond as illustrated in Fig. 2a. The products of biomass sediment, the dried biomass chunk and the biomass powder of N. oculata, were shown at Fig. 2b- The properties of algal biomass as a biofuel source were taken into consideration in this study. These properties varied widely, depended on the kind of algae, environmental culturing, cultivation periods, and harvesting conditions. Hence, investigating these properties was essential to determine the proper combustion technology. Figure 3 showed the EDX spectrograms of N. oculata biomass for determination of its compositions as compiled in Table 2. Generally, the investigated N. oculata biomass has low carbon, high oxygen, and high inorganic elements compared to the result of Patil et al. [45]. These compositions had an impact on biomass combustion and the residual characteristics. They were also needed for Fig. 1 The cell density of Nannochloropsis oculata during 7-day cultivation period. Relative standard error of means were below 5 % for all situations estimating the air required for the combustion process and for predicting the released gases. Carbon was oxidized during combustion by exothermic reactions and formed CO 2 . The organically bound of oxygen is released as the result of thermal processes, and it supplies a part of the overall oxygen needed for the combustion reactions [14]. The high amount presence of inorganic materials in this biomass, especially magnesium, calcium, sodium, silicon, and chlorine needs to be considered because they frequently results in slagging and fouling problems in furnaces. The reaction of alkali metals with silica presented in the ash can lead to the formation of low-melting silicates in fly ash particles yielding a sticky, mobile liquid phase, which causes blockages of airways in the furnace and boiler plant [46]. Cl vaporized during combustion, forming HCl, Cl 2 , and alkali chlorides. Alkali and alkaline earth chlorides are condensed in the boiler section as fly-ash particles or on the heat exchanger surfaces when flue gas temperature decreases [47]. Parts of the Cl were bounded in the fly ash while the rests were emitted as HCl in the flue gas. HCl emissions could play in the corrosion of metal component plant such as boilers and air pollution control devices. The TG curve for determining the proximate value was shown in Fig. 4. The values of moisture (M), volatile matter (VM), fixed carbon (FC), and ash (A) were directly determined from the TG curve by the difference while higher heating value (HHV) of the biomass was estimated by Eq. (3). All of these results were tabulated in Table 2.
As shown in Fig. 4, the first mass loss, which was indicated by the reaching of the first constant mass line, corresponded to moisture loss. The N. oculata moisture content was 3.99 %, which seemed to be a potential candidate for direct combustion. The moisture content influenced the combustion behavior and the amount of energy to evaporate water. The water content in the fuel had to be released before the first step combustion starting; hence high moisture content of biomass meant more energy for evaporation, and subsequently for heating the water vapor. Removal of water in the biomass would decrease the maximum possible combustion temperature and overall system efficiency. Aside from moisture evaporation that consumed a great deal of heat, it also caused the evaporation time to be extended during the combustion process. Hence, it resulted in the decay of ignition and affected the necessary residence time of biomass fuel in the combustion chamber before gasification and combustion taking place. Consequently, the high moisture fuel contents would require the larger combustion chambers and would result in an expansive boiler. Moreover, the amount of moisture also affected the burning reaction rate; thus, it influenced the generated gas emission as NO and CO, as well. In the devolatilization process, due to evaporated moisture moves away from the devolatilization front, the amount of volatile determined the reaction zone thickness [48], and it influenced the heat transfer to the devolatilization zone which affected the devolatilization rate. Thus, the moisture content was very important fuel parameter, and investigating this parameter was required to adjust the temperature control system of the furnace properly.
In line with the rising temperature, a major part of biomass organic component experienced thermal cracking then decomposed and volatilized to be the volatile matter. In inert gas, the volatile is released at temperature up to 900°C [39]. For microalgal biomass, it was especially resulted from the thermal cleavage of proteins, carbohydrates, and lipids. Table 2 showed that N. oculata volatile matter content was 67.45 %, lower than Chlorella sp. MP-1 that was 77.45 % [49] and higher than C. vulgaris that was 55.37 % [50]. The amount of biomass volatile matter strongly influenced the thermal decomposition and the combustion behavior. As it had been previously stated that the biomass, which had a high amount of volatiles, would be degraded as a result of the heating process. A significant part of the biomass was vaporized earlier before homogeneous gas phase combustion reactions took place and subsequently the remaining char undergone heterogeneous combustion reactions. Because of volatile matter was the reactive substance, hence, more volatile meant easier biomass to be burned. The aforementioned phenomenon would determine both of the ignition and burnout time of volatiles in the first stage of combustion processes, as well as the char combustion in the second stage. Moreover, in the context of co-combustion with other solid fuel, higher volatile could create larger fuel-rich regions in the nearburner region. The fuel-rich regions were very critical area. They were used for flame stabilization but, the formation of undesired prompt NO x , H 2 S, and soot could occur in this zone, as well [51][52][53]. Hence, finding out its amount is necessary to adjust the sufficiency of air supplied in the zone where volatile is released to improve combustion efficiency. Furthermore, the appropriate composition of supplied air in the released volatile zone will affect the formation of soot and NO emissions as discussed earlier by Liu et al. [54,55].
The fixed carbon content, which was the mass left over after the releases of volatiles excluding the ash and moisture contents, produced a char and was burned as a solid material in the combustion system. The N. oculata fixed carbon content was 8.08 %. This content was lower than both of C. vulgaris [50] and Chlorella sp. MP-1 [49], which were 34.35 and 16.95 %, respectively. The volatile matter and fixed carbon contents significance were that they provided a measure of the ease which the biomass could be gasified and oxidized in the combustion process. The N. oculata biomass, which had high volatile matter and low fixed carbon contents, was highly reactive fuel and would give a faster combustion rate during the devolatilization phase. This amount of fixed carbon was also needed to estimate the heating value of biomass, and it was acted as the main heat generator during the burning process.
The final residual material after the combustion process of biomass was ash, and it formed a standard measurement parameter for solid fuels. Table 2 indicated that N. oculata ash content was 24.47 %, which was very high, four times higher than Chlorella sp. MP-1 that was 6.36 % [49]. It was in accordance with the EDX analysis results, which showed the inorganic components content of N. oculata was high, as well. Inorganic components in biomass had a direct influence in the ash formation. Ash-forming elements exist in biomass as salts [14], bounded in the carbon structure, or they present as mineral particles from cultivation environment and introduce into the biomass fuel during harvest. In the combustion process, the part of the ash-forming compounds in biomass was vaporized and released to the gas phase while non-vaporized ash compounds that were left over in the char might melt and coalesce inside and on the surface of the char. The vaporized compounds would either be condensed or reacted on the surface of pre-existing ash particles in the flue gas when its temperature decreased. All of these could contribute to bed agglomeration, heat transfer surface fouling, and system corrosion. Furthermore, in the combustion process, the ash resulted from char burning would be formed as the layer surrounding their surface; hence, it inhibited the oxygen diffusion during char combustion. It affects both burning rate and mass loss rate, as well [56].
To address the problem of N. oculata's high ash content during thermal conversion processes, it might suitably blend this biomass in terms of co-combustion with other feedstocks to obtain the overall low ash content. One of the low ash biomass was rice straw, which its ash content was around 0.1-0.7 % by dry weight [57]. It might appropriate be blended with N. oculata to be mixed biomass fuel feedstock. However, their characteristics have not been studied yet.
Higher heating value was a total of heat yielded by the complete combustion of a unit quantity of fuels, including the latent heat contained in the water vapor. Therefore, it represented the maximum amount of energy which was    [9]. According to Illman et al. [9] the heating value of algae is in correlation with the lipid content of their biomass rather than with other components such as carbohydrates and proteins. As a comparison, the lipid content of N. oculata in this work was about 11 %, whereas C. vulgaris and C. minutissima lipid content were 18 and 31 %, respectively [9]. The FTIR spectrum of N. oculata biomass and its residue were shown in Fig. 5. For the biomass, it could be observed fifteen distinct transmission bands over the wave number range of 4,000-400/cm. These bands were assigned to specific molecular groups and were tentatively identified on the basis of biochemical reference standards and published FTIR spectra as quoted in Table 3. The cellular macromolecules (proteins, lipids, and carbohydrates) could be identified by their distinct transmittance in different frequency regions. The ''carbohydrate band spectra'' was characterized by weak and medium features at around 1,101-839/cm due to C-O and C-O-C stretching, Si-O stretching of siloxane silicate frustules, Si-OH bond stretching and bending of silanol. The ''protein band spectra'' was presented as less pronounced band at about 1,242/cm owing to asymmetric stretching of phosphodiester P=O. The spectrum of 1,435/cm related to CH 2 and CH 3 bending of methyl and C-O stretching of carboxylic group. The band at around 1,504/cm was amide II band spectra mainly m(C-H) and d (N-H). The medium amide I band at around 1,811-1,599/cm was primarily for C=O stretching of esters. The less pronounced band at 2,523/cm and around 3,659-3,003/cm because of amine salts -NH 3 ? stretching and N-H stretching of amide A, respectively. The bands associated with ''lipid band spectra'' were indicated by two weak peaks at around 2,940-2,835/cm related to CH 2 stretching of methylene and a strong peak at 1,788/cm as a result of C=O stretching of esters. The aforementioned bands spectra have specified the presence of the principal components in the N. oculata, namely carbohydrate, protein, and lipid. These components derived from various microalgae cell structure, such as a cell wall, plasma membrane, chloroplasts, mitochondrion, etc. Each cell structure substance would be progressively destroyed during the thermal processes when the temperature reached its decomposition temperature, and part of it released and formed volatile matter, whereas the remaining substance formed char as a solid material. Both of volatile and char would be burned through the combustion processes. The last rests after their complete burning processes were ash as residual materials.
Microalgal residue bands spectra were characterized by a strong feature at 3,645/cm related to O-H stretching of adsorbed water by silica presented in the ash, and strong, medium, and weak features at the fingerprint area associated with the rest of the inorganic component which was left in the ash. The band spectra between 1,490 and 1,410/ cm correlated with calcium carbonate, mainly due to antisymmetric CO 3 -stretching [58]. The features at around 1,200-900/cm region associated with the silica structure, especially due to Si-O stretching modes [59]. The peaks below 800/cm were vibrations of Ca-O and Mg-O [60]. The strong band at around 400-500/cm is caused by Si-O or Al-O bending vibrations [61]. The elements of ash content were critical parameter in that case of byproduct handling and utilization, as well as they have an impact on the overall processing cost of biomass conversion. However, the ash characterization, other than FTIR that have been previously stated, was not performed in this research, and it will be extensively investigated in the future studies. Figure 5 revealed the progressive degradation intensity in the spectra of biomass residue after 1,200°C, mainly at around 3,590-1,630/cm. The declined intensity was caused by the loss of protein and lipid components of biomass during thermal processes. The feature changes at fingerprint area associated with protein degradation of biomass mainly amide II. It also correlated with degradation of cell wall structures including their fibrillar component that composed of polymer of b-D-glucose and their amorphous mucilaginous material which constituted polysaccharides, lipids, and proteins.

Conclusions
The potential and properties of N. oculata biomass for futuristic renewable fuel have been studied. With traditionally natural and low-cost nutrient cultivation, this algae species grows rapidly. The physicochemical properties of this biomass also indicated that it is feasible as biofuel feedstock, except for its high content of inorganic components, which need special attention. The aforementioned attributes allow N. oculata to be a strong alternative renewable fuel, either by direct combustion under the proper handling for its residue or by co-combustion with other biomass feedstocks, which have low ash content such as rice straw, for reducing ash product. To optimize the usefulness of this biomass related to its productivity and appropriateness of combustion technology, it requires further in-depth research.