Correct path to use flumes in water resources management

The hydraulic characteristics of the flow are measured using tools such as flumes, in the design and evaluation of furrow irrigation systems. Proper use of these tools, such as their immersion while working, is one of the important executive points in this field; in this study, trapezoidal flumes are used to measure the intensity of input and output flow in furrow irrigation. The proper method of installing these flumes was investigated in this article. For this purpose, during 60 irrigation operations, the results showed that in order to create free flow conditions in these flumes, and not to affect the downstream and upstream current, as well as increasing the accuracy of measurements, in addition to installing flumes in all directions, trapezoidal flume should be installed at a height of at least about 4 cm above the furrow bed; according to the irrigation operations, the percentage of immersion in the installation of the flume at a height of 4 cm from the furrow bed was observed as standard (less than 70% immersion) in order to reduce the percentage of flow measurement error in different depths of water entering the flume. The results also showed that for ensuring free flow in trapezoidal flumes, the flume should be installed at a height of 4 cm or more above the furrow bed, provided the input ridges are strengthened and the end flume is measured to measure the inflow to the furrow. The output current of the furrow should be installed in the floor of the furrow along the bed to prevent the passage of current, provided that after the outflow flume, the furrow bed should be deeper in terms of free flow. Observance of the points and results obtained in this study in furrow irrigation systems prevents errors in flow measurement and consequently increases the accuracy in the design and evaluation of furrow irrigation systems.


Generalities
Flow measurement in industries, especially in irrigation networks, is a basic need; for example, in surface irrigation, inaccuracy in measuring flow intensity causes error in infiltration calculations (Nafchi et al. 2022;Fattahi Nafchi et al. 2022;Abdollahi et al. 2021;Talebmorad et al. 2021;Salehi-Hafshejani et al. 2019;Vanani et al. 2017;Ostad-Ali-Askar et al. 2018a;Shayannejad et al. 2022;Talebmorad et al. 2020;Trout and Mackey 1988;Ostad-Ali-Askari and Shayannejad 2015). In this regard, management tools such as flow intensity flow-meters have been designed, which are open channels with a special shape and narrowed throat section. They can be made of concrete, metal or fiberglass. There are standard flume designs that can measure discharge over a wide range of flows. The two most commonly used types of flumes are partial flume and trapezoidal flume. Flumes are applied in a smooth, uniform channel, creating a relatively small drop in water head. Flowmeters can accurately measure a wide range of flow. The flume should not be submerged (return water in the throat), and care should be taken in its installation. If the flow is free, by measuring a height at the inlet of the flume, the amount of flow can be measured using the formula governing that flume (Derakhshannia et al. 2020;Eslamian et al. 2018b;Golian et al. 2020;Aminpour et al. 2020). Prefabricated flumes can easily be used in cold regions with frosty winters. The cost of on-site flumes is relatively expensive. The components of a flume are the throat, the convergence and divergence section, the slope of the wall, the scale for measuring the depth of flow in the flume, etc., which must 1 3 187 Page 2 of 9 be accurately constructed and applied to measure the flow correctly (Eslamian et al. 2018a;Pirnazar et al. 2018;Ostad-Ali-Askari et al. 2019;Ostad-Ali-Askari et al. 2020a;Li et al. 2020). The name of the flume is determined by the size of the flume with its throat width, for example, 6-inch flume means a flume whose throat width is 6 inches (Larsen 1992).

(Parshall flume)
Today, partial flumes are a common tool in many measurements. This type of standard flume is well known and has been used for decades (Ribeiro et al. 2021). This type of flume was designed by Parshall between 1915and 1922(Parshall 1926, 1936. The partial flume has three main components, including the convergent part (upstream), the throat part and the divergent part (downstream) (Fig. 1). According to Fig. 1, the partial flume starts with a convergence at the bottom of the flume, next a downward slope in the throat and then an upward slope in the divergent section. The amount of current can be obtained by measuring the levels of ha and hb. Measuring the effluent flow, lack of particle deposition and consequently reducing the measurement error, reducing the water head drop are among the advantages of using partial flume, which is mostly due to their special shape ( Fig. 1) (Anonymous 1974 and1981).

Specifications
A new type of flume was built with high measurement accuracy with the advantages of previous flumes. They are easier to make than partial flume. Throat width in these flumes is zero and measures low currents; for example, they are used in furrow irrigation. The similarity of the shape of this flume with the cross sections of the field has made them more used in the fields. The shape of the trapezoidal flume is such that its sides diverge from the floor of the flume to its surface relative to each other; therefore, it transmits more current than the partial flume, which is not the case (comparison of Figs. 1 and 2). The condition for using flumes is less than 70% submerged current, i.e., no upstream current does not affect the measurements. In trapezoidal flume, this percentage is higher than partial flume and above 80%, and therefore without using a correction factor (which should be used for reporting) flow rate can be shown with very little error

Installing trapezoidal flume
The installation method of trapezoidal flumes is similar to the partial flume and should be level in both longitudinal and transverse directions. However, if this flume is used on a sloping surface, the maximum allowable slope for installation should be observed, and the numbers read on the slope should be corrected according to the correction of the number zero on the slope; the depth of the flow (h1) is the height of the inlet cross-section floor to the flow surface. The depth h1 is measured to measure the flow rate, then placed in a formula for which the flow has already been calibrated and afterward the flow rate is measured. This formula is derived from the equation of energy and the equation of continuity (Dabrowski and Polak 2012). According to the mentioned cases, installing a trapezoidal flume depends on the slope of the channel if the maximum allowable slope is observed (mostly 0.0035 m/m or critical slope) the floor of the flume with the floor of the channel can be the same from the bottom of the canal. It is worth noting that the inlet of the flume is installed in such a way as to create a free flow, which requires the installation of a flume at a suitable height above the floor of the canal. If there is no free flow in the trapezoidal flume and the ratio of water depth at the outlet of the flume (h4) to water depth at the inlet of the flume (h1) (Fig. 2) is 80% or more, i.e., the upstream flow affects the downstream, the correction factor is used to calculate the current intensity (Fig. 3).
Considering the importance of the correct method of installing trapezoidal flume and the few scientific resources that exist in irrigation, especially furrow irrigation, in this article, the correct method of using trapezoidal flumes in furrow irrigation systems is examined. Providing the correct method for installing this flume creates free flow conditions. As a result, accurate flow measurement is one of the requirements for accurate infiltration calculation and consequently accurate design and evaluation of furrow irrigation systems (

Methods and materials
In this research, WSC type 2 trapezoidal flume was used in order to achieve the correct method of using trapezoidal flume and in furrow irrigation systems, and the experiments were repeated during 60 furrow irrigation operations finally the results were reviewed. The purpose of this article is to create non-submersible flow conditions with proper installation of this flume. Furrow irrigation operations were performed on farms located in Isfahan-Iran University of Technology. The length, width and depth of these furrows were 42 m, 60 and 20 cm, respectively, and the slope was 0.1% (with the maximum allowable slope). In these irrigation operations, a flume at the beginning of the furrow to measure the inflow and a flume at the end of the furrow to measure the output flow (using the calibrated formula in Table 1) were installed evenly in all directions. Therefore, this type of flume was installed 120 times in different ways and the flow was examined. Also, the soil around pounded and the flume was installed in this regard in order to prevent the flow of leakage around the flume. In all operations, in cases where free flow and submerged current were established, all the conditions for installing the flume, including the installation depth, etc., were recorded.  Q is the actual discharge and Q0 is the observational discharge. h4 = water depth at the outlet of the flume (Fig. 2). (Robinson 1966(Robinson , 1968Larsen 1992) WinFlume software was also used to simulate the test conditions. The calculations required to calibrate the flume, determine its size and deploy it can be used by utilizing this software. The maximum and minimum error rates between the simulated discharge by this software and the actual measured discharge are 5% and 25%, respectively, and the average error is 13%. This model estimates the discharge more than the reality. The higher the flow rate through the flume, the lower the error. Also, the higher the sill height, the closer the flow in the gorge to the critical flow if the upstream and downstream slopes of the flume floor are equal (Wahl 2001).

Results and discussion
The results of 120 trapezoidal flume installations during various irrigation operations in this study showed that nonsubmersible flow occurs in this flume when the flume is installed at a height of at least about 4 cm from the bottom of the furrow. Because the allowable immersion percentage is less than 80% in this case. The flow will be measured with good accuracy (Fig. 4). Irrigation operations showed that the walls of the furrow should be hammered and tightened before installing the inflow (Fig. 4) in order to ensure the accuracy of measuring the inflow to the furrow in the primary flume, in addition to the above conditions, and the height of the walls should be increased as much as possible. Also, in the end flume to measure the output flow from the groove, the bottom of the flume should be the same as the bottom of the groove due to the blockage of the flow to pass, especially at the beginning of the flow time to the flume, which causes errors in calculations. Upon reaching it, the current is easily transferred from the bottom of the furrow to the bottom of the flume and passes easily through it. This should be done under the condition that the furrow surface should be at least 2 m deeper after the installation site to ensure non-submersible flow in the outlet flume.
The trapezoidal flume used in WinFlume software was simulated to further investigate and simulate irrigation operations. The results of modeling the existing flume (WSC flume type 2) by WinFlume software were as follows: In this section, the percentage of immersion, which is the ratio of water height upstream and downstream, can be obtained. The above steps (Figs. 5,6,7 and 8) were for the height of 3.5 cm of flume floor from the furrow (sill height = 3.5 cm) repeated for different heights such as 3 cm and 4 cm and the percentage of immersion in the heights. Different water levels were obtained and compared. Table 2 is prepared for this purpose.
The results show that in sill height = 4 cm, the percentage of immersion is less than other installation heights, which indicates the accuracy of the results of field operations in this study. Also the higher the inlet flow rate (higher altitude), the higher the immersion percentage at a certain height.
The values of error percentage resulting in flow estimation by WinFlume software to the actual flow rate (measured by flume according to its formula) are shown in Table 3 based on the discharge operating range in the experiments of this study for flume.
Percentage error at any flow depth = (actual flow rate − sowftwore flow rate) × 100 actual flow rate The results showed that the higher the flow depth, the higher the software measurement error and the average measurement error at 3.5 and 4 cm flume floor heights is similar to the furrow and slightly lower at 4 cm depth; this shows the correct expression of the test results by WinFlume software.

Conclusions and recommendations
For this purpose, during 60 irrigation operations, the results showed that in order to create free flow conditions in these flumes, and not to affect the downstream and upstream current, as well as increasing the accuracy of measurements, in addition to installing flumes in all directions, trapezoidal flume should be installed at a height of at least about 4 cm above the furrow bed; according to the irrigation operations, the percentage of immersion in the installation of the flume at a height of four centimeters from the furrow bed was observed as standard (less than 70% immersion) in order to reduce the percentage of flow measurement error in different depths of water entering the flume. The results also showed that for ensuring free flow in trapezoidal flumes, the flume should be installed at a height of four centimeters or more above the furrow bed, provided the input ridges are strengthened and the end flume is measured to measure the inflow to the furrow. The output current of the furrow should be installed in the floor of the furrow along the bed to prevent the passage of current; provided that after the outflow flume, the furrow bed should be deeper in terms of free flow. Observance of the points and results obtained in this study in furrow irrigation systems prevents errors in flow measurement and consequently increases the accuracy in the design and evaluation of furrow irrigation systems.
Based on field experiments and simulations performed in this research, it is recommended that the WSC flume type 2 can be installed at least 4 cm from the bottom of the furrow to work in free-flow mode in furrow irrigation. It should be noted that the flow conditions for this result are the inlet flow to the furrow about one liter per second and the maximum allowable slope (0.0035 m per meter) and by pounding and strengthening the wall of the furrow at the inlet. This flume  should be installed in the bottom of the furrow to create free flow conditions and also not to prevent it from passing, and in a few meters after installing this flume, conditions should be created in the bottom of the furrow so that the flow does not return to the flume. Obviously, the installation height of the boats varies according to the flow conditions. It is suggested to increase the accuracy of the studies, the appropriate method of using tools for this purpose before each test with respect to the importance of field measurements and the problems of their determination. Also tools are simulated, designed and calibrated by WinFlume, Flow3D to increase the accuracy of the experiments.