Pyrolysis Behaviours of Microalgae Nannochloropsis gaditana

In this study, the pyrolysis behaviours of marine microalgae biomass, Nannochloropsis gaditana, were investigated at three different temperatures (400, 500, 600 °C). Experiments were conducted in the presence of N2 with a flow rate of 50 cm3/h using a 1-kg fixed-bed reactor. The effects of pyrolysis conditions such as temperature on product yields were studied. The char, bio-oil, and gaseous samples obtained were analysed for elemental trace metals using inductively coupled plasma atomic emission spectroscopy (ICP-OES) and gas chromatography with mass detection (GC–MS). Raw Nannochloropsis gaditana samples were also analysed by pyrolysis–gas chromatography–mass spectrometry (Py–GC–MS). Mass and energy balances were calculated. The results indicate that the bio-oil from the pyrolysis of Nannochloropsis gaditana under 600 °C had the highest heating value (12.6 MJ/kg) and was obtained with the highest efficiency (38–40%). Alkanes and alkenes, such as tetradecane, pentadecane, heptadecene, and octadecene, were identified in the liquid products, and the highest contents of alkanes and alkenes were determined in the bio-oil obtained under 500 °C. In these pyrolysis conditions, gaseous products exhibited the highest concentrations of methane (greater than 50% in the maximum range). These properties of the bio-oil and its gaseous products demonstrated that Nannochloropsis gaditana can be used as a renewable energy resource and chemical feedstock. The biochar from all processes contained almost 70% ash and, in this particular case, can be used as, for example, a fertilizer because it does not contain any heavy metals.

will originate from biomass by 2020. It is estimated that energy crops will constitute a major part of the bioenergy sources. Energy resources from energy crops will increase from 0.8-2.0 EJ/yr (2010) to 4.3-6.0 EJ/yr in 2030 and that from agricultural residues will increase from 0.8-3.9 EJ/yr (2010) to 0.6-5.0 EJ/yr in 2050. Energy resources from forest biomass have been estimated to be 0.8-10.6 EJ/yr [5,6].
One of the most promising renewable sources of energy is algae biomass. Algae are photosynthetic plant organisms that can rapidly increase their community mass. The energetic utilization of algae can be divided into three groups. Heterotrophic algae are able to take up organic molecules from their external environment and convert these molecules into proteins and fatty acids. Autotrophic algae are able to conduct photosynthesis to harness sunlight and fix the inorganic carbon from atmospheric CO 2 . During photosynthesis, algae synthesize sugars through many biochemical transformations. Mixotrophic algae may simultaneously conduct photosynthesis and obtain organic molecules. Photosynthetic algae have the potential to utilize CO 2 emissions and offer the potential for a carbon-neutral biofuel. Based on their morphology and size, algae can be divided into two groups: macroalgae and microalgae. Macroalgae are composed of multiple cells and can form structures such as roots, stems, and leaves. Macroalgae are frequently used in the food industry. Microalgae are microscopic, mainly unicellular, plant organisms characterized by their rapid growth rates, effective biofixation of carbon dioxide, and rich lipid contents. Depending on the species, the lipid content of the cells of microalgae can range from 10 to 70%. It is assumed that microalgae can utilize 1.8 kg of carbon dioxide per 1 kg of dry biomass [7][8][9][10]. Algae biomass can be used for many processes, such as combustion, gasification, pyrolysis, and digestion. Anaerobic digestion of algae biomass allows for the production of bioethanol and biogas [7,11]. However, algae biomass is most commonly used for the production of biodiesel. Based on their high productivity and lipid content, microalgae are an alternative source of biomass for the production of biodiesel. There are several possibilities for obtaining biodiesel from algae, e.g., chemical/mechanical extraction or thermic conversion of biomass. After isolation, the crude oil must then be subjected to transesterification and purification [12][13][14].
This type of biomass is recognized as an energy crop or feedstock for biorefineries, and according to studies, macroalgae or seaweed can also be viewed as a waste problem when it is spontaneously deposited on shorelines, creating hygienic problems. Often, the proposed solution is to utilize this waste in thermal processing applications that include combustion, gasification, and pyrolysis. Many authors have focused on the kinetics and thermal characterization of microalgae and marine biomass, and as a result these aspects have been widely studied [15][16][17][18][19][20].
Pyrolysis is the thermal degradation of materials in the absence of oxygen. Pyrolysis is a promising thermic process for obtaining liquid products. In this process, the quantity and quality of the biochars, bio-oil, and gaseous products depend on the pyrolysis conditions, e.g., the pyrolysis temperature, gas flow rate, pressure, and heating rate, and the particle size of the material used in the process [15,[21][22][23][24]. Algae biomass contains a large amount of lipids; therefore, pyrolysis can be used to extract bio-oil. Moreover, the resulting charcoal can be used as a sorbent, fertilizer, or fuel, and the gas can be used as a gaseous fuel. The aim of this work is to evaluate the fixed-bed pyrolysis of the marine microalgae Nannochloropsis gaditana under different temperature conditions. The resulting charcoal, liquid products, and gas have been analysed in detail. This paper also gives information regarding the degree of energy self-sufficiency of the biomass pyrolysis process depending on the biomass humidity content, directly informing the literature, which otherwise contains no available information concerning the direct pyrolysis of microalgae.

Materials and Methods
The microalgae N. gaditana was prepared by drying to 2-5% humidity (W t r ). Next, the microalgae samples were placed in a steel retort and then pyrolysed under a nitrogen atmosphere. Nitrogen was pumped into the retort from the bottom at a flow rate of 50 cm 3 /h. Prior to pyrolysis, the sample was purged with nitrogen for 10-15 min, and then the sample was heated to the aforementioned temperature at a heating rate of 20 K/min. The pyrolysis process was conducted three times for each temperature of interest (400, 500, 600 °C). After reaching the desired temperature, each sample was maintained under the experimental conditions for 30 min before cooling to room temperature. Figure 1 presents a schematic of the laboratory-scale setup applied to the presented research. During the process, char, liquid, and gaseous samples were collected for further analysis. All processes were performed in triplicate to ensure that the reactions were repeatable and stable.
Pyrolysis was conducted as a batch process using a processing furnace supplied by the IZO Company (Poland). The furnace was equipped with a stainless steel retort (0.24 m in height and 0.07 m in diameter). The temperature maximum of the furnace model was 1500 °C, and its settings could be controlled to within ±5 °C. The furnace was equipped with a thermocouple that extended into the retort, and both the furnace and the retort temperatures could be read continuously. To control the temperature, two type S thermocouples (PtRh10%-Pt) were used. The thermocouples were maintained in the retort axis at the positions of approximately 1/3 and 2/3 of the retort height.
The required heating rate and nearly constant temperature conditions of pyrolysis were achieved using a temperature control system. The heating rate can, in general, be set at 1-50 °C/min by varying the number of ramps, controlled directly by the control system. The sample size was generally between 100 and 200 g, but this value depended on the density of the material that was used for the pyrolysis. The retort was purged with N 2 at a rate of 50 cm 3 /h, which was controlled by mass flow controllers. The bio-oil was collected in a set of laboratory glass bottles (approximately 100 mL) connected in series. All glass bottles were chilled to a temperature of approximately 0 °C in a cooling bath (ethylene glycol) using refrigerated circulators. The gaseous products were directly analysed using an extractive gas analyser (SICK. USA).

Proximate Analysis
Volatile Matter Content Determination Using a Gravimetric Method [26] The volatile matter content (VM) was determined by weighing an open crucible without air at 850 ± 15 °C for 7 min. Then, the difference between the total weight loss and weight loss due to the evaporation of water was calculated.
Ash Content Determination [27] The ash content was determined by incinerating the samples in a muffle furnace, which consisted of heating the samples in air at a specific rate to a temperature of 815 ± 10 °C and maintaining this temperature until a constant weight was reached.

Ultimate Analysis
Determination of Carbon, Hydrogen, Nitrogen, and Sulphur Contents [28] The samples were subjected to an automated quantitative combustion process in an oxygen stream at 1150 °C and then transferred through a quartz bridge into a reduction tube in which the sulphur and nitrogen oxides were reduced to SO 2 and N 2 in the presence of copper. The combustion gases at the reduction tube outlet were transferred into a dynamic separation system in which the absorption columns were desorbed thermally in sequence. These gases (N 2 , CO 2 , H 2 O, and SO 2 ) were identified using a thermal conductivity detector (TCD). Low SO 2 concentrations were analysed using an NDIR detector.
Determination of Oxygen Content [28] Direct quantitative analysis of the oxygen content was performed by pyrolysing a sample under an H 2 O-, CO 2 -, and O 2 -free reductive atmosphere (95% N 2 and 5% H 2 ) at 1120-1150 °C. The sample was placed in a pyrolysis tube filled with elemental carbon, and carbon dioxide was obtained as a result of the reaction between the oxygen in the sample and carbon from the filling (Boudouard equilibrium). The acidic pyrolysis products, such as H 2 S, HCN, and HCl, were absorbed by granulated NaOH, and the produced water was absorbed by Fig. 1 Schematic of the laboratory setup for the thermal conversion of biomass and PP blends [25] a dehumidifier. The inert pyrolysis products (N 2 and CH 4 ) were directed into a measurement cell with carbon monoxide. Because the NDIR detector was sensitive only to CO, the other gases did not have to be separated. The elementary C t a , H t a , N a , S t a , and O t a compositions were measured using a Vario MACRO Cube automatic elemental analyser. All values of measurement uncertainty for the carbon, oxygen, nitrogen, hydrogen, and sulphur concentrations are presented in Table 1.
Higher Heating Values of Fuels The high heating values in our studies were calculated from the elemental composition using the Milne [29] approach according to Eq. (1):

Determination of Properties of the Liquid and Gaseous
Fractions The properties of the gaseous fraction were analysed using a CO, CO 2 , H 2 , and CH 4 automatic gas analyser. GC analyses were performed with a Varian CP-3800 gas chromatograph with FID and TCD detectors and a 100% dimethylpolysiloxane (60 m, 0.25 mm i.d., 0.25 μm film thickness) capillary column. The chromatographic programme included: 45 °C for 2 min, then a programmed temperature ramp to 160 °C (heating rate 8 °C/min to 90 °C, then 20 °C/min to 160 °C). Helium was used as the carrier gas (1.0 mL/min). The calorific value of the gaseous fraction was calculated according to the calorific value of the partial gas components. In the case of liquid fraction analysis, the GC analyses were performed with a Trace Ultra Thermo Scientific gas chromatograph with FID and a Crossbond polyethylene glycol (60 m, 0.35 mm i.d., 0.5 μm film thickness) capillary column. The chromatographic programme included: 50 °C for 5 min, then a programmed temperature ramp to 200 °C (heating rate 10 °C/min to 200 °C). Helium was also used as the carrier gas in this case (2.5 mL/min). The liquid products due to the sample's heterogeneous character were dissolved in isopropanol in order to standardize (1) the samples. This chromatograph with Crossbond polyethylene glycol column allows the light organic compounds to be analysed.
Determination of the Trace Metals Trace elements in the N. gaditana biomass were analysed using an ICP-OES analyser. Inductively coupled plasma optical emission spectrometry is based on the study of atomic spectra. The inductively coupled plasma is used to produce excited atoms and ions that emit electromagnetic radiation at wavelengths characteristic of a particular element. The temperature in the electromagnetic field is in the range from 6000 to 10,000 K. The determination of the trace metals includes the following steps: conducting solid and liquid samples into aqueous solutions, organic matter removal, and ICP-OES spectrometer analysis. Emission spectrometric analysis is preceded by spectrometer calibration by measuring the radiation emission characteristic of the individual elements of the standard solutions and blanks. The sample solution is taken in for analysis using a peristaltic pump. The pump provides a constant flow of the sample into the sputtering chamber by a nebulizer. The aerosolised sample is injected into the canter of the plasma, at which point the atoms are excited. As a result of returning the excited atoms to their original state, radiation is emitted. The radiation beam is directed to

Results and Discussion
The algae biomass used in this study is characterized by a relatively large ash content compared to other such (strains) biomass samples; however, its higher heating value was greater than 21 MJ. The N. gaditana microalgae sample used in the pyrolysis process, and all of the products obtained through this process, was subjected to basic analyses, including according to the methods previously described here and the methods reported in [25].
The physical and chemical properties of the algae biomass used in this study are presented in Tables 1 and 2. Table 3 presents the results of the proximate analysis of raw biomass and biochars obtained under different pyrolysis conditions.
The biomass samples were pyrolysed at three temperatures (400, 500, and 600 °C) to determine the effects of temperature on the products. The efficiencies of the processes were calculated according to Eq. (2) and are shown in Fig. 2: where W ij is the pyrolysis process efficiency (i) for the jth fraction (solid, liquid, gas), M j is the weight of the jth fraction (solid, liquid, gas), and M is the weight of the mixed batch used in the process (pyrolysis).
The effects of increasing the temperature on the concentrations of liquid products in the pyrolysis test occurred at the expense of reducing the amount of gaseous products (Fig. 2). This is a highly desirable phenomenon with regard to the possibility of using algae biomass for the generation of liquid fuels via thermal conversion. For the marine biomass tested in this research, the yield of liquid product obtained under 500 °C was approximately 17% higher ( Fig. 1) than that obtained under 400 °C. Higher yields were also observed for the carbon concentration and heat of combustion of the liquid products, by 13.4 and 7.2%, respectively (Table 4). A similar dependence was observed in the fixed-bed pyrolysis of marine algae biomass. In the slow pyrolysis of Saccharina japonica, a greater number of liquid products were observed with increasing pyrolysis temperature [30]. After the fixed-bed pyrolysis of S. japonica (470 °C), 37.9% of the liquid products were obtained [31]. The amount of liquid products obtained from the slow pyrolysis of S. japonica was similar to its pyrolysis at 500 °C in our study. In Table 3, the elemental analysis results and energy balance for each product in relation to the biomass processed via pyrolysis are presented. The heating value of the liquid products calculated for a temperature of 500 °C gave a similar heating value of liquid products from the process of slow pyrolysis (450 °C) for two other species of microalgae, Scenedesmus and Spirulina. The heating value of the liquid products obtained from the pyrolysis of N. gaditana at 500 °C reached 31.8 MJ/ kg, whereas the pyrolysis of Scenedesmus and Spirulina at 450 °C gave the values of 36.7 and 35.2 MJ/kg, respectively. The ratios of the pyrolytic products were similar for all three species of microalgae [32].  The increase of carbon content in the liquid products is associated with an intensification of the thermal degradation process of the solid fraction into easily condensable organic compounds (decreased quantities of gas). This process qualitatively and quantitatively influences the characteristics of the liquid products obtained during the thermal conversion of algae at 400 and 500 °C. These changes are presented as chromatograms in Fig. 3 and in tabular form in Table 5.
As can easily be observed (Fig. 3), the intensification of the thermal conversion process has a significant effect on the characteristics of the liquid products obtained from the investigated biomass. For the liquid products obtained at 400 °C, the qualitative and quantitative gas chromatography analyses were able to determine the concentrations of six organic compounds, namely acetone, methanol, ethylbenzene, n-pentadecane, n-pentadecene, and furfuryl alcohol. In comparison with the pyrolysis of seaweeds (Enteromorpha clathrata and Sargassum natans) [33], the typical compounds derived from the decomposition of lignins (e.g., phenol) or lipids (e.g., n-pentadecane, n-pentadecene) were identified.
Increasing the pyrolysis temperature to 500 °C influences the composition of the liquid products, which made it possible to qualitatively and quantitatively determine the next 11 compounds. Table 5 presents the concentration of each of the analysed compounds and the differences in concentration between the liquid fractions obtained at 400 and 500 °C. For methanol and n-pentadecene, the concentration in the liquid fraction obtained at 500 °C was lower than that obtained at the lower temperature. This result can be associated with the breakage of double bonds that occurred  during the pyrolysis reaction, which confirmed the increase in its homologue n-pentadecane. In the remaining products, increases in the concentrations were observed ( Table 6).
As mentioned previously, all products, including the gaseous products, were subjected to quantitative and qualitative analyses. In the present study, we used a gas analyser to determine the gas composition during the pyrolysis process in real time (continuous process, online gas analysis). Figures 4 and 5 show the variations in the concentrations of hydrogen, methane, carbon monoxide, and carbon dioxide recorded online during the pyrolysis. After increasing the temperature from 400 to 500 °C, the concentration of methane in the process gas was changed from 6 to 28%, a threefold increase in the hydrogen concentration to approximately 6%, and a slight increase in the other gas components during the test. It was also noted that increasing the temperature to 500 °C caused the yield of the obtained gaseous products to decrease by 7% and, at the same time, the calorific value of process gas was increased by 0.7%.
In the subsequent studies, we increased the pyrolysis temperature by 100 °C, which resulted in a further increase in the volume of the liquid fraction to 37% (an increase of 6%). We also observed 9-10% bio-oil increases compared to the heat of combustion for the fraction obtained at 500 °C, which was due to the increase of the carbon and hydrogen contents in the final product. Further analysis and comparison of the properties of the bio-oil obtained at 600 °C to the bio-oil properties obtained at 500 °C clearly revealed that the increase in the heat of combustion was associated with an increase in the content of methanol in the liquid fraction (a fourfold increase). As can be observed in the chromatograms (Fig. 6), the quality of the liquid fraction in the present case did not significantly change. In addition to the increase in the methanol content, the  (Table 6). In the studied case, phenol (0.97 mg/g) and methyl phenol (1.17 mg/g) are likely derived from the lipid fraction [34].
Upon comparing the results for the gaseous products obtained at 500 and 600 °C, a further increase in the component concentrations in the product (process gases) was noted (Fig. 7): • 24% for methane, • 4-6% for carbon dioxide, • 8% for hydrogen, and • 4% for carbon monoxide. As in the previous case, the temperature increase resulted in a 6% reduction in the yield of gaseous products, which reduced the amount of energy by almost 10%. In the slow pyrolysis of Nannochloropsis at 500 and 600 °C, a significant quantity of methane, from 2 to 5% of the total weight of the feedstock, was observed. Compared to the slow pyrolysis at 500 °C of other species of microalgae [35], the amount of methane ranged from 1 to 2% of the total weight of the feedstock. The recovered heating value of combustible gases from the slow pyrolysis of microalgae was comparable to that of other forms of biomass such as grass (10.0 MJ/kg), wood (16.7 MJ/kg), or rice husk (7.4 MJ/kg). The results obtained under the slow pyrolysis of Nannochloropsis were compared with the results from the analytical pyrolysis. In the first pyrolysis step, at 200 °C (Fig. 8) 70 min). Most of these compounds are separated from the studied biomass sample at 200 °C, which is why they are not visible after further increasing the temperature from 200 to 300 °C. In this temperature range, a small amount of phytol acetate (51.58 min) is observed.
The temperature increase from 300 to 400 °C resulted in a further thermal decomposition of the studied material, whereby the following set of organic compounds is released: toluene (3.69 min), resorcinol (16. (66.78 min). These chemical components are observed also in the temperature range between 400 and 500 °C but at lower concentrations. In the studied microalgae bio-oil, nitriles such as hexadecanenitrile, which are derived from fatty oxygenates, were analysed. In addition, protein-derived compounds such as indole were observed and may be produced from the decomposition of tryptophan amino acids [40].
The final temperature range of 500-600 °C resulted in a further thermal decomposition of the studied material, which released the following organic compounds: dodecane (19. All results from the Py-GC-MS analysis of Nannochloropsis treated with rapid pyrolysis between 200 and 600 °C are presented in Table 7. The main groups of aromatic hydrocarbons, heterocyclics, phenols, amines, amides, indoles, alkanes, and nitriles were found in the bio-oil. The length of the carbon chain in the bio-oil was in the range of C3-C22, and the boiling point of the oil fell in the range of 56 °C for acetone to 356 °C for heneicosane. Thus, the biooil property is between that of the oil from kerosene, diesel, and light gas oil [41]. Bio-oils (not only from microalgae pyrolysis but generally from the pyrolysis of biomass) are a complex mixture, highly oxygenated with a great amount of large-size molecules, which nearly involve all species of oxygenated organics, such as esters, ethers, aldehydes, ketones, phenols, carboxylic acids, and alcohols [42].
A comparison of the typical properties of fossil oils and bio-oils based on the slow and fast pyrolysis of wood   Table 8. The pyrolysis of biomass bio-oils usually yields higher oxygen concentrations than that of fossil oil. This causes bio-oils to be more reactive than and not as stable as fossil fuels, and their characteristics change rapidly during condensation and under storage conditions [43]. To utilize bio-oils as a fuel for chemical feedstock sources, some improvements to their stability and high heating value are required. However, as shown in Table 8, the pyrolysis oil obtained from microalgae N. gaditana has a lower oxygen concentration (on average by 10%) than the oil obtained during wood biomass pyrolysis. As a result, this oil will be more stable than bio-oil from wood biomass. Oils from microalgae pyrolysis have higher HHV values than wood bio-oil obtained from fast pyrolysis [45] but is lower than wood bio-oil from slow pyrolysis [44]. The HHV of bio-oil from the studied microalgae was between 18.2 and 21.5 MJ/kg, depending on which temperature condition was utilized. In conclusion, the physical and chemical properties of microalgae bio-oil make it more suitable for fuel oil use than pyrolysis oils from lignocellulosic biomass feedstocks.

Degree of Coverage Heat Demand for the Pyrolysis Process of Microalgae Biomass
To estimate the heat demand for the pyrolysis process, the following assumptions and conditions were used: • the process was conducted in a steel retort in batch mode, and the capacity of the retort was 100 g; • the moisture content in the biomass intended for pyrolysis was established at five levels from 5 to 60%; • the final temperature of the process was established at three levels, namely 400, 500, and 600 °C; • the number of liquid and gaseous products depended on the pyrolysis conditions (the results of the experiments); • the liquid products had a water content of 4%; • the calorific values of the liquid and gaseous products depended on the pyrolysis temperature conditions (the results of the experiments); • the calculations did not include the exothermic and endothermic heats of reaction occurring during the pyrolysis of the fuel, and it was assumed that their net energy effect was close to zero; • the heat required to supply the reactor and to account for heat loss during the process, which was 15% of the heat required to perform pyrolysis; • the calculations did not include the heat required to partially dry the biomass to a desired moisture content because it was assumed that the waste heat from the exhaust gases could be used for this purpose.
Analysis of the heat demand of the pyrolysis process allows the degree of energy self-sufficiency of this process to be estimated, which may be expressed by Eq. (3,4) [44]: where Q self-suffic . is the degree of energy self-sufficiency of the thermal conversion process (%), Q w products is the heat energy from the burning products (e.g., gaseous products) (MJ/t), and Q pyrol. process is the heat energy demand of the pyrolysis process (MJ/t).
where c b is the heat capacity of the biomass (kJ/kg K), w b is the mass fraction of the biomass (%), T is the temperature of the thermal conversion process (°C), ΔH vap is the enthalpy of water vaporization (kJ/kg), W a is the moisture content (%), and Q loss is the heat loss from the thermal conversion process (kJ/kg).
During the pyrolysis of marine biomass, the efficiency is correlated with the degree of energy self-sufficiency and  based on the pyrolysis conditions. The demand for heat and electricity may be minimized. Due to a wide range of biomass moisture content (particularly marine biomass, the moisture content of which can be greater than 70%) in the energy balance calculation, we assumed that the process was conducted in the temperature range from 400 to 600 °C with variable humidity in the range from 5 to 60%. Under these conditions, dried algae biomass with a moisture content of 5% can maximize the yield of the solid and liquid fractions (under 500 and 600 °C) and can achieve a degree of energy self-sufficiency greater than 100% during pyrolysis using its gaseous products as a fuel to provide energy to the system (Fig. 9). As shown in Fig. 9, the most unfavourable conditions for conducting an autothermal pyrolysis process are when the humidity of marine biomass exceeds 60%. In this case, the degree of energy self-sufficiency of the process was <50%. This effect can be minimized or even excluded for the tested biomass by utilizing not only the process gas for energy harvesting but also a portion of the char. According to our calculations, the amount sufficient for this case to achieve autothermal reaction of the assumed parameters is 35%.

Conclusion
In the presented paper, the mass and energy balance and analysis of the pyrolysis products of N. gaditana marine biomass under different pyrolysis conditions were carried out. Both the mass/energy balance and characteristics of the pyrolysis products depend on temperature. At higher pyrolysis temperatures, more liquid and less gaseous products were observed. The liquid products from pyrolysis at 500 °C contained the most alkenes and alkanes. The presence of hydrocarbons in the liquid product is indicative of the potential to use the bio-oil from N. gaditana pyrolysis for the production of biofuels and biocomponents. In the liquid products, several products of cellulose degradation (hydroxyacetone) or lignin degradation (phenols) were also identified. The ash content was determined from the biochar and was equal to approximately 68%. The ash-rich biochar can be used as a fertilizer or biocomponent. The use of this ash as a fertilizer would be possible due to the low content of heavy metals in the tested algae biomass. In optimal pyrolysis conditions (600 °C), gaseous products are rich in methane (greater than 50%). After purification, this gas can be used as a fuel or further processed for the production of methanol or hydrogen. An important factor contributing to the pyrolysis process is the degree of humidity of the feedstock. The higher moisture content of the material used in the pyrolysis process increases the amount of energy needed to carry out the process. The biomass of the marine species N. gaditana may have the potential for use in pyrolysis processes either to obtain methane-rich gases, for yielding a bio-oil that contains hydrocarbons, or for biochar which may be used in the fertilizer industry.