A Novel Geometry Optimization Approach for Multi-Recess Hydrostatic Bearing Pad Operating in Static and low-Speed Conditions Using CFD Simulation

The design of a hydrostatic bearing pad is limited to simple geometry using analytical equations or one-parameter optimization based on experimental data. This study proposes and investigates a new two-parameter method for estimating optimal hydrostatic bearing pad proportions—recess area and position, using Computational Fluid Dynamics (CFD). In this study, 3D static CFD quarter model of a multi-recess hydrostatic bearing pad assuming laminar flow is used. The CFD model was calibrated based on experimentally obtained results and the literature. The recess pressure and resulting load are evaluated for a variety of recess positions and areas. Performance factors are calculated and interpolated in the MATLAB environment. Using the proposed novel two-parameter optimization, the energetic loss was reduced by 20% compared to the classical one-parameter approach. This methodology allows versatile and effective design of optimal hydrostatic bearings operating in low-speed conditions to achieve minimum energetic loss.


Introduction
Hydrostatic (HS) bearings are a vital part of high-precision machines whose sizes range from millimeters up to tens of meters [1]. They are widely used in machining centers, guideways, turntables, space telescopes, and hydro-energetics [2][3][4][5]. The main advantages are operation at zero speed, very low friction, minimal wear, high stiffness, and good damping ability. The possibility to operate at zero speed creates a huge advantage for the operation of hydrodynamic bearings in low-speed conditions. Thus, they are frequently combined with HS bearings to improve the performance and reduce wear during low-speed operation and start and stop phases [6,7]. Such bearings are called hybrid bearings. On the contrary, it is necessary to continuously supply the bearing with pressurized lubricant to maintain a uniform lubricating layer and proper function. The energetic requirements and initial costs are considerably higher than that for other bearing types. Nevertheless, interest in replacing large rotors 1 3 52 Page 2 of 14 rolling bearings has been rising in recent years to reduce downtime and maintenance costs [8].
The working principle is shown in Fig. 1. Lubricant is supplied by a hydraulic circuit into the recesses of the pad. The generated pressure then lifts the load and separates the solid bodies of the bearing pad and turntable (in case of circular bearings) or slider (in case of guideways). Then, a lubricating film of thickness usually in the range of 10-100 µm is created. The lubricant outflowing from the narrow gap is returned to the hydraulic circuit. The restrictor plays an important role in achieving high stiffness, stability, and control. Many types of such devices have been proposed to improve the bearing performance, such as orifice [9,10], membrane members [11], or feedback systems [12]. The lubricant supply is necessary for proper function while moving or until the required sliding speed is reached, in the case of hybrid bearings, for the hydrodynamic effect to occur and carry the load. Liu et al. [13] concluded that HS bearings have had an increasing trend of research interest over the last few years. Therefore, it is crucial to design the HS bearing pad for the best performance and minimal energetic demands, which are increasing with the size of the bearing. He and Wang [14] added that the implementation of the best available technology in the industry can reduce the total energy consumption in some fields by up to 20%, which is a significant amount of energy directly affecting the environment and the final product or service price.
The geometry of the hydrostatic bearing is one of the key parameters that affect the lubricant pressure distribution and the bearing resulting performance [15]. Loeb and Rippel [16] introduced the determination of the optimal pad shape using an electric field plotter analogy [17], where the optimal shape can be determined using performance factors for a variety of pad shapes using experimentally obtained curves. Subsequently, Rippel [18] published a design manual for HS bearings. Khonsari and Booser [19] published a book dealing with tribological aspects in engineering applications, including hydrostatic bearing shape optimization based on Loeb and Rippel [16] methodology. Based on previous research, Bassani and Piccigallo [20] presented a comprehensive methodology for the design of HS bearings describing the most important parameters and design considerations. Chikurov [21] later continued modeling HS bearings using the electric field analogy for possible simplification. A very important step in the HS bearing design process is optimization to achieve the best performance and reduce energetic demands as much as possible [22,23]. This is especially crucial in large-scale HS bearings, where the energy consumption is significant [24]. To achieve the best performance and stability, a multicriterion optimization approach should be considered [25]. Simple pad geometries, such as circular pads and recesses, have been analytically derived [19]. However, in cases of complex and multi-recess pads, the analytical solution becomes very complicated, and the performance characteristics must be obtained experimentally or using a numerical approach.
Computational Fluid Dynamics (CFD) has been increasingly used in various applications over the past decade. One of the key advantages of this method is that it allows one to obtain many parameters and investigate flow characteristics in areas where it is extremely difficult or even impossible to implement sensors or use optical methods. CFD has already been used to study hydrodynamic, HS, and hybrid bearings [26][27][28]. Sharma et al. [29] conducted a numerical study to determine the performance of unconventional hybrid bearings. It has been shown that hybrid bearings perform with lower pressure and temperature peaks, which leads to higher bearing stability [30,31]. However, it is crucial to determine the accuracy of the model. Cui et al. [32] investigated heavy HS bearing using a quarter CFD model and obtained errors under 10% compared to analytical approaches. Gao and colleagues [10] studied the effect of orifice length in HS bearings and compared the CFD model with experiments that reached errors under 1%. The experiments are crucial to CFD model validation, especially in cases where exact analytical approaches cannot be used. Wasilczuk et al. [33] concluded that the presence of HS pockets in hydrodynamic bearings reduces the temperature change and pressure peaks, leading to higher reliability of the hybrid bearing, but the drawback of the presence of the pocket is the larger friction losses due to the cooler oil. Wodtke et al. [34] carried out experimental validation for theoretical calculations and predictions of large hydrodynamic Fig. 1 Scheme of the bearing parts and working principle thrust bearings and emphasized the necessity of experimental validation of numerical simulations, which are simplified and thus do not represent the real geometry and other influential effects. Helene et al. [35] conducted a parametric study of the flow pattern in the 2D recess of a hybrid bearing based on Navier-Stokes equations with the comparison of laminar and turbulent flow regimes. The authors concluded that the modeling of the turbulent flow regime could contribute to better understanding of the inertia and viscous effects in recess bearings. For that reason, turbulent models were later used by Ghezali et al. [36] and Gao et al. [10] in hydrostatic bearing orifice performance numerical investigation of flows of higher Reynolds numbers. Horvat and Braun [37] extended the study of numerical flow characteristics to 3D HS journal bearings with experimental validation using laser flow visualization of streamline maps at a high rotational speed. A similar study was later conducted on HS thrust bearings to investigate geometric patterns and different pad shapes, concluding that the presented model may be useful in HS bearing load-carrying capacity and stiffness of HS bearings for low-speed applications [38]. Du et al. [39] proposed an analytical model for the analysis of the pressure of tilted HS journal bearings validated using a CFD and experimental procedure. Guo et al. [40] performed a comparison of CFD codes for static and dynamic properties in hydrodynamic and HS bearing applications. The authors agree that CFD will play an important role in bearing and damper analysis in future research. The comparison of CFD standard code to a special one made for HS, hydrodynamic any hybrid bearing analyses showed good agreement, which leads to a conclusion that general codes might be used for the investigation of such bearings and their static and dynamic characteristics.
The CFD can significantly speed up the development, reduce costs, and provide detailed information about the flow character and many parameters. Although the CFD approach is widely adopted in various applications, including HS, hydrodynamic, and hybrid bearings, it is necessary to set appropriate boundary conditions and verify the results obtained with an experimental approach [41][42][43]. Moreover, many papers dealing with CFD analyses of HS bearings have been proposed over the last years, although only a few of them offered practical design recommendations. This article aims to optimize recess size and position in HS bearing pads to minimize energetic loss while achieving the best performance for static and low-speed conditions. The presented geometry optimization multi-parameter approach using area ratio and recess position has not yet been proposed.

Materials and Methods
Three approaches were used to verify the obtained resultsanalytical, experimental, and CFD. An integrated process was also followed to create and analyze the results using these three methods, as shown in Fig. 2. Based on the analytical calculation, experimental conditions were determined. Afterward, boundary conditions of the CFD analysis were set according to the resulting analytical results and experimental conditions. Subsequently, all results were compared and discussed.

Analytical Approach
Navier-Stokes equations play a significant role in the field of fluid mechanics. Nonetheless, due to the complexity of the Navier-Stokes equations, it is almost impossible to obtain analytical expressions to calculate required flow characteristics. Therefore, certain assumptions can be considered to help to obtain a simpler form of equations. The assumptions are as follows: 1. Film thickness is constant and small compared to its size in other directions. 2. The fluid is Newtonian, incompressible, and isoviscous. 3. Inertia terms are negligible compared to the viscous forces. 4. No squeeze nor sliding exists and the bearing surfaces are stationary. 5. The pressure of lubricant is constant in the direction of the film thickness ( p∕ z = 0). 6. There is a continuous supply of lubricant, and the flow is laminar.
Then, the Reynolds equation for computation of the pressure distribution in the simplified form is as follows: After obtaining the pressure distribution, the load-carrying capacity (or acting force) can be expressed as follows: where P s is the recess pressure and A eff is the effective area of the pad, which can be expressed from effective pad area proportion β (β < 1) and total area of the pad A tot : Eqs. (1-3) can be further customized and utilized to express required flow supply to the bearing as follows: where h is the film thickness, µ is the dynamic viscosity of lubricant, and Q f is the flow factor, dependent on the geometry and the effective area of the bearing.
Loeb [17] introduced a new methodology for estimating optimal proportions of the bearing pad and recess based on electric analog field plotter. Generalized analytical equations could be used to calculate the bearing performance using read values obtained from graphs, presented in Loeb and Rippel [16]. Similarly, the performance factors (Eq. 5-7) can be determined based on known values of bearing characteristics.
Eqs. (5,6) can be transformed to obtain the required variable from the expression. An example of designing a HS bearing pad proportions using one-parameter optimization is shown in Fig. 3. The ratio (a/l) represents the characteristic dimension of the recess to the characteristic dimension of the pad, that is, the diameter of the recess to the pad edge length. One primary parameter is kept constant (usually recess size to retain the required lifting area), while the other is optimized. The aim of the pad geometry optimization is generally to achieve the best possible performance with minimal pumping power loss, in this case, the power loss factor-H f . And for the

Fig. 3
An example design chart using one-parameter optimization with geometry description from Loeb and Rippel [16] (a/l) ratio of the minimum power loss factor, the values of optimal pressure (P f ) and flow (Q f ) factors are obtained, respectively. Performance factors for the experimental pad proportions can be found in (Table 1). This study assumes relative performance change independently on the pump efficiency, what is not the aim of this study, thus the parameter η was assumed as 1 for simplification.
In the basic approach, only one of the two parameters: a or l are used, while the recess position (t = l) is assumed. The optimization approach using performance curves in a 2D graph utilizes (l = 4a). However, we defined the new variable parameter (t) to describe the position of the recess. Thus, the proposed method uses two-parameter criteria, recess position (t), and recess area-to-total pad area ratio (A r /A tot ) for performance optimization. The area and the position of the recess were chosen as the primary parameters because the recess shapes may be chosen to better accommodate the pad shape and thus improve the bearing performance. The length of the edge of the pad (2 l) remained constant, so the second variable assumed in this study was the recess radius (a). Attention should be paid to prevent exceeding the recess area out of the pad geometry, i.e., in case the pad has rounded corners.

Lubricant Viscosity
To obtain all the inputs required to build a relevant mathematical model, the dynamic viscosity measurement was performed on a rotational viscometer from HAAKE RotoVisco® 1 (PSL Systemtechnik, Germany). Measured data were filtered with 99.88% reliability using a Bingham rheological model. The dynamic viscosity of the used ISO VG 46 grade hydraulic oil was fitted using the Vogel-Fulcher equation with R 2 = 99.89%. The experiments were carried in static conditions, with stable temperature 23 °C recorded using temperature sensors in the recess. The results showed very low temperature difference throughout the measurements, only ± 1 °C. Thus, constant viscosity of 0.104 Pa•s was considered in all simulations. It has been previously observed by Schmelzer et al. [44] that the pressure-viscosity dependence of liquids of constant composition is extremely small (around 2%) in the investigated pressure range (0-1 MPa). Therefore, the pressure-viscosity dependence was neglected in this study.

Two-Pad HS Experimental Bearing (2-PAD)
The experimental device used to obtain the measured data for evaluation is schematically shown in Fig. 4. It consists of two main parts, the bearing and the hydraulic circuit, which supplies pressurized lubricant with a pump powered by an electromotor. The hydraulic circuit is equipped with safety features, such as a check valve and a pressure relief valve. The hydraulic accumulator minimizes the pressure spikes generated by the pump. The flowmeter measures the total supplied flow to the whole bearing. Flow restrictors (throttle valves) secure bearing stability in the event of asymmetrical load or misalignment. A pressure sensor of 0.25 bar precision is mounted on each of the inlets to the recess. The lubricant that flows out of the contact area to the collector is returned to the oil tank. Three-contact potentiometer proximity sensors are mounted on each of the 2-PAD pads for obtaining film thickness with precision of 0.01 mm and range of 3 mm. To measure the actual temperature in the recess area, a thermometer is fitted in each of the recesses for calculation of the viscosity value of the lubricant. The load is created using four set screws, each mounted with a load cell with ± 5 N precision, which provides a real-time measurement of the loading force. The experimental measurements were carried out three times after the temperature in the recess area stabilized at 23 °C (corresponding to a dynamic viscosity of 0.104 Pa•s). Since the hydraulic circuit has relatively large tank (100 l), no additional cooling was necessary. The experimental conditions were based on the previous test bearing comparison with analytical equations in ref. [45]. The total supplied flow into both pads was set to 8.5 l/min. A comparison of predicted and measured film thickness with variable load was presented in reference [45], where the highest precision was achieved at 16-kN load. Therefore, for all measurements, a total load of 16 kN were applied in this study. The resulting average film thickness was 0.197 mm. The pad size used in experiments was 140 × 140 mm with recess diameters of 35 mm and positions of t = 35 mm and recess depth was 5 mm. The inlet was 40 mm long and of 8 mm diameter (Fig. 5).

Numerical Approach
CFD analysis has become a favored method for the analysis of fluid dynamics. It provides a detailed understanding of the lubricant flow in hydrostatic bearings. In this study, the CFD analysis was done using commercial software ANSYS Fluent 2021 R2 based on the Finite Volume Method with Cell-Centered formulation. The code solves the conservation equations for mass (Eq. 8) and momentum (Eq. 9), respectively.
In this case, pressure-based steady-state incompressible flow with absolute velocity formulation was investigated without considering thermal effects and gravity. A uniform lubricant film was considered in all simulations. The Reynolds number estimation was below 10 and the laminar flow regime is expected in the film region, thus laminar model was selected. Because of relatively high film thickness and  Table 2. The simulation of all design points was conducted using the setting described below. An important rule to avoid the recess area outreaching the pad area must be checked before proceeding with the simulation parametrization.
The quarter model of the fluid domain was discretized into an unstructured polyhedral mesh in built-in ANSYS Fluent Meshing (\* MERGEFORMAT Fig. 6). Mesh refinement was set on the top plane to enhance the results of the pressure and resulting forces acting on this plane. Three sets of meshes were compared using Richardson Extrapolation method [46]. Discretization error was calculated from a theoretical extrapolated value based on the results from the three sets of equally spaced meshes. Three boundary layers were added to the walls in the lubricating film region to enhance near wall fluid behavior in the top plane area, from which the results were evaluated. Due to the large difference between lubricating film height and recess depth, element growth rate was set to 1.05 to ensure slow transition of the elements. The final mesh selection was based on the results in Table 3. The precision of the model was also judged according to the analytically predicted and experimentally obtained results. It is also possible to optimize bearings with smaller film thickness using this method, but it may require longer computational times to secure smooth mesh element transition from the recess area to the film region.
A uniform film thickness of 0.197 mm, as obtained from experimental measurements, was used for all design points. The boundary conditions can be seen in Fig. 6. Starting with the mass flow inlet (Q) set at 0.015 kg/s on the face of 40-mm-long inlet pipe. Symmetry conditions  were employed on the symmetry planes of the quarter model and pressure outlet with atmospheric pressure operating condition (P atm ). Output parameters were the resulting force on the top plane of the bearing and average pressure over the recess area on the top plane. The residuals of continuity and momentum equations condition were set below 10 −4 to achieve convergence. Under relaxation factors for both velocity and pressure were set at 0.5 and 0.5, respectively, without any further need for adjustment. We used the coupled pressure-velocity coupling scheme, which should provide robust and high performance for steady-state flows compared to the segregated schemes available in ANSYS Fluent. The gradient least square-based spatial discretization method was used. The first-choice schemes-second order and second-order upwind were kept for pressure and momentum, respectively. Hybrid initialization was conducted to improve the convergence of each case. One case took approximately 20 min to discretize and solve with the used computer specifications: 12 physical cores of 3.47 GHz processor, 96 GB of RAM, and 1 TB SSD to store retained case data.

Results and Discussion
Firstly, the comparison of results obtained from experiments, calculations, and CFD simulations were performed to validate the CFD model precision. Subsequently, all design points were calculated and evaluated for the performance factors and shape optimization.

Model Calibration
The total load applied per pad was obtained based on three measurements using load cells with sensor precision of 3% and resulting average deviation under 0.5%. The recess pressure was obtained from pressure sensors in each of the recess with 5% sensor precision and resulting average deviation under 1% based on three measurements. The calculated load was obtained using information from sensors mounted on the pad. Then, a 3D CFD model was created and computed for the same geometry as on the experimental device. The results are shown in Fig. 7 for (a) load and (b) recess pressure. The CFD results for the load were obtained from resulting force acting on the top (contact) plane of the model. The weight of slider and loading frame was included in load evaluation. The experimental results show relatively good agreement with the calculation considering the precision of the used sensors. The recess depth influence on the performance might have affected the results as well, since analytical calculation does not assume this geometric parameter. The obtained difference from analytical calculation in load was − 3.2% for experimental results and + 0.65% for CFD, respectively. The difference in results of recess pressure compared to the analytical approach reached − 7.5% for experiments and + 5.3% for the CFD analysis. The values obtained experimentally exhibit lower values due to the simplifications that are assumed in analytical and CFD computation, respectively. Despite a constant viscosity was assumed in all simulations to determine optimal geometry, so that the comparison of various shapes was unaffected, additional influence of the results could be caused by the dynamic viscosity variation with temperature, which approximately changes by 5% for 1 °C. A minor contribution to the results difference could be caused by the geometry imperfections of the HS bearing (surface flatness and roughness) or the recess depth effect influence, which is in the case of analytical calculation neglected. Nonetheless, the obtained results were of satisfactory precision to carry on with the model parametrization.

Design Point Computation and Evaluation
After conducting the initial comparison of the different approaches, the numerical CFD study was solved for all the design points from Table 2. The performance factors P f , Q f , and H f were calculated from the results obtained using Eqs. (5-7) for all design points. The results of all performance factors are shown in Figs. 8, 9, and 10 in the form of (a) 3D graphs with the variable recess on the y-axis and variable area ratio on the x-axis, forming the two-parameter approach and (b) area ratio sections for better readability of the obtained data. Generally, the optimization goal is to achieve the lowest P f , Q f , and H f , assuming Eqs. (5-7). The load factor (Fig. 8) shows a similar trend as in the reference experimentally obtained 2D graph from [16], but in a different scale. The results for the load factor indicate that the load-carrying capacity decreases with increasing area ratio or position from the origin, separately and together. The larger the area ratio, the smaller the load factor. The lowest value of P f can be found in the middle sector of the graph. Nonetheless, as seen in Fig. 11, the largest area ratio creates a very small sealing edge and thus is extremely sensitive to the pad misalignment and asymmetrical loading. In the case of flow factor (Fig. 9), it is obvious that the larger the area ratio or the farther the position of the recess from the center, the higher flow is required to sustain certain film thickness or load-carrying capacity. As for the flow factor, the closer to the pad center the recess is, the smaller the actual value. The smaller the area ratio is, the better performance will be achieved. Ultimately, the power loss factor (Fig. 10) expresses the overall performance-to secure an optimum between the highest load capacity and the lowest power requirements (as expressed in Fig. 3). Therefore, to achieve the lowest energy requirements, a minimal H f should be considered. In the case of open-type bearings (without counter pads, as explained in ref. [1]), the recess position should be chosen, also considering the ability of the bearing to manage asymmetrical loading and pad misalignment. This is another reason why the multi-parameter approach offers a more versatile design process compared to the classical one-parameter approach. For this reason, pressure contours of the various pad shapes from smallest and closest to the pad center, to the farthest and biggest (Fig. 11). It is obvious, that the larger the land area (as for the smallest area ratio), the higher the recess pressure. Nonetheless, the load capacity and ability to manage asymmetrical loading and misalignment are not desirable in this case (Fig. 11a). The recess pressure was gradually decreasing with increasing recess size and distance from the pad center (Fig. 11b). The highest ability to manage asymmetrical loading was achieved with largest recess size (Fig. 11c). The sealing edge is very small in this case and the pressure gradient is the steepest (Fig. 12) for this configuration, which makes the bearing extremely sensitive to pad misalignment. Even though the smallest load factor was obtained, the largest flow factor resulted for this case, which is undesirable.

Optimal Shape Determination
To determine the optimal shape of the bearing, the minimum power loss factor was searched for. To obtain a more accurate result, the minimum was not chosen from the calculated values of the design points, but using a cubic interpolated surface as seen in Fig. 13. This step allowed us to look for the minimum value of the power loss factor also between the calculated points. The calculated points were used to fit the cubic interpolated surface with normalization in MATLAB R2021a. It is also possible to use linear interpolation, which is simpler but does not capture the surface trend and curvature as well as the cubic interpolation. Subsequently, a minimum value of the power loss factor was found. Then, the coordinates of the minimum value expressed the optimal shape-the recess position and area ratio, respectively. The minimum value of the power loss factor, 30.66, obtained by CFD simulation was determined for the recess position 17.66 mm from the center and an area ratio of 0.2. In contrast, optimal value of the power loss factor obtained from the graph presented by Loeb and Rippel [16] is 38, with recess position of 35 mm and area ratio of 0.132. Compared to the basic approach using oneparameter criteria, a 20% reduction of the power loss factor was achieved. The investigated ranges of recess position and area ratio were chosen according to the pad size and computable geometry. The interpolated grid could be finer if even higher precision was required. The deformed grid areas on the left side of the 3D graph in Fig. 13 are only a graphical representation of the grid fitted over the sample points and thus are not evaluated.
Finally, we compared the pressure contours of the optimal shape obtained from the classical approach (Fig. 14a) and the presented two-parameter approach (Fig. 14b), respectively. The classical approach optimization resulted in smaller recess diameter and its farther position from the Fig. 13 Power loss factor cubic interpolation of results obtained from CFD analysis with highlighted minimal power loss factor for 2-parameter optimization (H fCFD ) and using 1-parameter optimization (H f ) based on [16] Fig. 14 Top plane static pressure contours of optimized pad shapes using a one-parameter approach and b novel two-parameter approach pad center compared to the two-parameter approach, which also resulted in higher recess pressure due to larger sealing edge. As can be seen in the comparison of the two pressure contours (Fig. 14), the one-parameter approach performed with pressure decrease in the central area, while the two-parameter approach showed uniform pressure among the four recesses. This has also been observed in all twoparameter approach pressure contours as seen in Fig. 11. The results indicate that the proposed method provides more uniform pressure distribution and contributes to higher bearing load capacity, stiffness, and ability to carry asymmetrical loading and pad misalignment. The only drawback of this geometry might be worsened ability to assess the behavior of each of the recesses separately. Nonetheless, discharge grooves can be added to solve this issue [26].

Conclusion
This paper presents a novel approach to HS multi-recess thrust bearing pad geometry optimization using results based on CFD simulations. The precision of the CFD model was compared to the analytical and experimental results. The proposed two-parameter criterion was used to evaluate the optimal shape-recess position and recess area-to-pad area ratio. The obtained results from two-parameter optimization show a possible 20% power loss factor reduction, which is directly related to pumping power loss, compared to the case of conventionally used one-parameter criterion. Moreover, it has been observed that the position of the recess has a strong influence on the resulting performance and thus the size and position should be evaluated independently. The pressure contours indicate that the proposed two-parameter method provides more even pressure distribution in the central area of the pad, resulting in higher load capacity, stiffness, and ability to manage asymmetrical loading and pad misalignment. The optimization scheme tailored for best performance at lowest energetic requirements can be used for various shapes with custom defined geometric parameters. The proposed method might bring about a notable reduction in the energetic demands, especially for bearings of large-scale structures. Although in the presented study a cross-symmetrical four recess HS bearing pad geometry was optimized, this approach can be applied to any shape of HS bearing and a wide range of operating conditions-from very low to extremely high loads and recess pressures. It is necessary to determine the area ratio and position of the recess grooves first, then perform CFD analysis of selected design points, and find the minimal power loss factor. The drawback of the presented method is the computational time required to evaluate all design points, which nonetheless, depends on the machine used for simulations.
Further research might aim at full experimental evaluation of the presented 3D optimization graphs. The next steps might lead to the preparation of 3D optimization graphs for the mostly used bearing pad geometries to improve the design process of HS bearings. This approach could be used also for journal HS bearings. The precision of the model presented in this article could be further improved by considering the influence of sliding speed and thermal effects and sliding surface geometric precision (i.e., manufacturing and assembly errors). Very little attention has been paid to the structural deformation of the slider/turntable caused by the pressurized fluid flow. An experimental verification of real effects on bearing performance would provide valuable information for design engineers.