Influence of Isomeric Composition and Sample Handling on the Liquid Density of Hydrofluorethers Measured by Vibrating Tube Densimeter at 0.1 MPa

Hydrofluoroethers (HFEs) represent a new family of promising engineering fluids suitable for technical cleaning and cooling of electronic and magnetic devices or as admixtures in refrigerant blends. Here, we report accurate data for the liquid density at 0.1 MPa and temperatures from 273.15K\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$273.15\,\text{K}$$\end{document} to 343.15K\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$343.15\,\text{K}$$\end{document} for a series of five HFEs, namely, HFE-7000, HFE-7100, HFE-7200, HFE-7300, and HFE-7500. A highly sensitive vibrating tube densimeter with a borosilicate glass U-tube calibrated according to the procedure by Prokopová et al. (J Chem Thermodyn 173:106855, 2022) provided density data with an expanded uncertainty (k=2\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$k=2$$\end{document}) of 0.13kg·m-3\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$0.13\,\text{kg}\cdot \text{m}^{-3}$$\end{document}. Influences such as sample degassing, water content, or sample temperature before its dosing into the densimeter are discussed. Thanks to the high sensitivity of the used densimeter, an unexpected shift in the density of different HFE-7100 and HFE-7200 liquid samples was detected. Unlike other HFEs, HFE-7100 and HFE-7200 are mixtures of two hardly separable isomers, which were so far considered having identical thermophysical properties. Utilizing nuclear magnetic resonance spectroscopy, the ratio of n-isomer and iso-isomer was inspected for various liquid samples. In the range of iso-isomer mole fraction from 0.61 to 0.77, the new measurements revealed density differences of more than 5kg·m-3\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$5\,\text{kg}\cdot \text{m}^{-3}$$\end{document} in case of HFE-7100 and of about 3kg·m-3\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$3\,\text{kg}\cdot \text{m}^{-3}$$\end{document} in case of HFE-7200. Consequently, for some applications, the properties of different HFE isomers cannot be considered identical. The Rackett-type correlation for the saturated liquid density was fitted using the new and the literature data.


Introduction
The fluorinated ethers, also known under the commercial name Novec TM intro- duced by the 3M company [1], are receiving increasing attention from researchers and engineers as promising alternatives to chloro-fluoro-hydrocarbons over the past two decades.Hydrofluoroethers (HFEs) are excellent heat transfer fluids suitable for cooling of electronic and magnetic devices, cleaning and blowing agents, or lowboiling components in refrigerant blends.In comparison with other commonly used engineering fluids, HFEs cause zero ozone depletion and have relatively low global warming potential (GWP) and high dielectric constant.However, it should be noted that since HFEs belong to per-and polyfluoroalkyl substances (PFASs), their wider use may be limited in future.For an effective and reliable use of fluorinated ethers, the accurate description of their thermodynamic properties such as density, vapor pressure, excess molar volume, and transport properties such as viscosity or surface tension is crucial.Several research groups have recently provided valuable experimental data on some of these properties [2][3][4][5] and developed predictive models mostly based on the SAFT-type equations of state [6][7][8].Nevertheless, the introduced models have limited ranges of validity and for some applications unsatisfactory accuracy.The available property data are still rather limited in order to develop and verify accurate models valid over wide temperature and pressure ranges such as empirical multiparameter equations of state [9] as included in NIST's REFPROP package [10].
An interesting phenomenon that has not been addressed in detail is the isomeric composition of some HFE fluids, namely, HFE-7100 which is a trade name of binary isomer mixture of 1,1,1,2,2,3,3,4,4-nonafluoro-4-methoxybutane and 1,1,1,2,3,3-hexafluoro-3-methoxy-2-(trifluoromethyl)propane, and HFE-7200 being a trade name of binary isomer mixture of 1-ethoxy-1,1,2,2,3,3,4,4,4-nonafluorobutane and 1-ethoxy-1,1,2,3,3,3-hexafluoro-2-(trifluoromethyl)-propane.Since the isomers of the HFE-7100 and HFE-7200 mixtures are similar substances with the same functional groups, the relative volatility of the substances can be expected to be close to 1.As a result, the isomers are difficult to separate from each other, e.g., by gas-liquid chromatography [11].Therefore, most producers, including the 3M company, declare HFE-7100 and HFE-7200 as mixtures of two inseparable isomers with essentially identical properties.Consequently, the thermophysical properties of these fluids such as the boiling point or liquid density are reported as for a pure substance [12,13].On the other hand, our new experiments slightly undermine this simplification.Sensitive measurements carried out with the vibrating tube densimeter (VTD) revealed density differences of up to 6.4 kg ⋅ m −3 and 3.1 kg ⋅ m −3 between different batches of HFE-7100 and HFE-7200, respectively.These differences are remarkably larger compared to other single-isomer HFE fluids, i.e., HFE-7000, HFE-7300, and HFE-7500, which showed only small differences in densities of up to 0.6 kg ⋅ m −3 between the different production batches.The detected five to ten times higher discrepancies in the liquid density point to the effect of isomeric composition of HFE-7100 and HFE-7200.
The main goal of this work is to provide reference liquid density data at 0.1 MPa for a series of HFE fluids, specified in Table 1, and to shed light on the influence of HFE isomeric composition.The composition of the mixture may change during sample handling due to different evaporation of individual components.We have therefore tried to trace various experimental effects such as temperature during the sample handling or different level of degassing that can influence the sample composition and the measured liquid density.Accurate data for liquid density are necessary for the next step of description of HFE properties, e.g., for the development of multiparameter equations of state [9].

Experimental
A highly sensitive vibrating tube densimeter with a borosilicate glass U-tube was used for the measurement of liquid density at barometric pressure for a series of different HFE samples.The new data were collected in the temperature range from 273 K to the vicinity of the normal boiling point.

Materials
Description of all samples of five different HFE fluids and one pure isomer 1,1,2,3,3,3-hexafluoro-1-methoxy-2-(trifluoromethyl)propane, here called HFE-7100-iso, including their purity and water content is summarized in Tables 1 and 2. No further purification was applied except for the degassing of 5 ml sample in a 10-ml plastic syringe by applying repeatedly a slight vacuum for about 10 s.Samples used for the reference measurement of liquid density at 0.1 MPa were degassed four times.Further details on the sample degassing and the change of sample composition in case of two-isomer liquids due to evaporation are given in the Results section.The water content was measured utilizing the Karl-Fischer coulometric titrator (Mettler Toledo C30) or taken from analytical certificates.It is recommended to have at least 50 μg of water in the sample in case of coulometric analysis.For very dry samples, for which the measured water content was under the detection limit (UDL) of the titrator, a water mass fraction lower than 10 × 10 −6 was assumed.With regard to values given in Table 2, the HFE samples can be considered almost waterfree.All samples were stored in the refrigerator at a temperature of 278 K.The samples were taken directly from the bottle with a sterile syringe, quickly degassed and dispensed into the VTD U-tube or further processed in order to intentionally alter the composition of isomeric mixtures.

Vibrating Tube Densimeter
Vibrating tube densimeters are very sensitive instruments for the measurement of fluid densities ranging from gases to dense liquids.When carefully calibrated, the standard combined uncertainties in the order of ± 0.10 kg ⋅ m −3 can be achieved [15-17] for the high-pressure instruments equipped with the metal U-or V-shaped vibrating tubes.The low-pressure units with glass tubes can attain even one order of magnitude lower standard combined uncertainties of ± 0.010 kg ⋅ m −3 [18-20].
In this work, the vibrating tube densimeter of Anton Paar, model DMA 5000 M [21] with a borosilicate glass U-tube was used.With a resolution down to 0.001 kg ⋅ m −3 , the instrument belongs to the most sensitive VTDs.The densimeter was operated and calibrated according to the procedure described in previous work [20].The calibration technique inspired by the approach of Fritz et al. [22] employs a series of repeated measurements with ultra-pure water and dry air.In short, the fluid density can be determined from the following equation where PQ = ∕ ref is a relative period of oscillation, A and B are temperature-depend- ent parameters obtained from the reference measurements with water and air over the temperature range from 273 K to 363 K, and ΔD 0 (T) = D 0,sample (T) − D 0,air (T) is the damping difference of the measured sample and dry air at a given temperature T. V 1 and V 2 are the damping coefficients reflecting the influence of sample viscosity.
The HFE samples were measured in the range from T = 273 K to the temperatures 4 K to 60 K below the normal boiling point depending on the sample volatility.Due to the rather high evaporation of most HFE samples, both the inlet and outlet openings of the VTD U-tube were loosely closed with teflon plugs to guarantee constant sample composition during the whole measurement.Several experimental setups leading to the prevention of evaporation of the sample from the U-tube were tested.The differences in sample densities obtained in the way of the U-tube plugged and unplugged were below 0.030 kg ⋅ m −3 , i.e., they lie within the expanded uncertainty ( k = 2 ) of the density data of 0.13 kg ⋅ m −3 .Each sample measurement was followed by water measurements and at least every 10 days by dry air measurements to check the calibration parameters and stability of VTD over time.The final densities of the HFE samples were calculated based on the temperature dependent parameters A and B obtained from the measurement campaign of at least 5 water and 3 air measurements.

Results and Discussion
Tables 3, 4, 5, 6, and 7 summarize the experimental data for the liquid density of five HFE fluids.The density data represent the average values of two to three measurements with different samples from each batch specified in Table 2 the measurements were carried out with the U-tube inputs loosely plugged, the liquid pressure can be considered slightly higher than the reported barometric pressure measured with a high-precision external pressure gauge Druck DPI 142 (GE, USA).An internal Pt100 temperature probe located close to the tip of the U-tube was inspected as described in previous work [20].

Isomeric Composition of HFE-7100 and HFE-7200
Tables 8 and 9 provide the density data of different HFE-7100 and HFE-7200 samples depending on the mole fraction of the iso-isomer at three temperatures of 283 K, 298 K, and 303 K. New data are compared with the literature sources containing the information on the composition of the isomeric mixture.The composition dependence of the liquid density at 0.1 MPa of all known samples is depicted in Fig. 3.As can be seen, the density of both liquids gradually increases with the higher content of the iso-isomer.In the typical composition range with the mole       fraction of iso-isomer from 0.6 to 0.8, the detected density difference reaches 5 kg ⋅ m −3 and 3 kg ⋅ m −3 in case of HFE-7100 and HFE-7200, respectively.These differences considerably overreach the expanded uncertainty of most experimental data, which are typically in the range of 0.1 to 1 kg ⋅ m −3 .It should be noted that the influence of isomeric composition of HFE-7100 and HFE-7200 can be neglected in most engineering applications.On the other hand, it needs to be considered in the development of accurate property models such as empirical multiparameter equations of state [9].Moreover, due to favorable properties such as low hygroscopicity, HFE fluids are viewed as good candidates for calibration liquids, e.g., for accurate density measurement.If so, we recommend focusing predominantly on the single isomeric HFE fluids.

Temperature Correlation for Saturated Liquid Density of HFEs
The new density data obtained at 0.1 MPa together with the low-pressure data taken from the literature were fitted with the Rackett-type correlation [26].The correlation, given in the form of Eq. 2, provides good predictions for the saturated liquid density of all five HFEs.
In Eq. 2, parameter A approximates the critical density crit and B can be considered as the critical compressibility factor Z crit .We note that Vetere [26] employed a universal value of exponent N of 2/7 that can be used for less described liquids.In general, various values for N usually in the range from 0.1 to 0.5 are used when representing low-pressure experimental data, e.g., as reported by Outcalt et al. [4,27].
Except for HFE-7000, exponent N was set equal to 0.30 which provides good representation of all available density data by achieving acceptable reproduction of the critical point estimated by Aminian et al. [28].Table 10 summarizes the parameters of Eq. 2 for the five selected HFEs obtained from the minimization of the following objective function with N exp standing for the number of density data points, U i for the expanded uncer- tainty (k = 2) , and w i for the weight lying between 0 and 1.The weight equaled to 1.0, except for the data points from the previous work [6] whose weight was set to 0.1-more details are given in the discussion of Figs. 4, 5, 6, 7, and 8. Average values of the standard deviation of the correlated parameters are also provided.Critical temperature T crit was taken from Aminian et al. [28].Values of parameter A are approximately 4 % higher than the critical density crit estimated recently by Aminian et al. [28].It shall be emphasized that correlation (2) is based on the experimental data in the temperature range typically from 273 K to 363 K.However, it is expected to provide reasonable prediction for the saturated liquid density also at higher temperatures as it follows the temperature trend toward the critical point density.
Table 10 also provides the values for the expanded relative deviation of Eq. 2 from the correlated experimental data.The relative deviations for HFE-7100 and HFE-7200 are considerably larger compared to other three single isomeric HFEs.This indicates greater scatter of the density data due to the two-isomer composition of HFE-7100 and HFE-7200.10.The blue dash-dotted lines correspond to correlations given as linear functions of temperature in 3M datasheets [12,13,[29][30][31].As can be seen, the 3M correlations deviate from the available experimental data by several tenths of a percent.The largest discrepancies can be seen in case of HFE-7100 as shown in Fig. 5.It should be noted that the 3M correlations were developed before most of the experimental data were published and as such should be viewed as preliminary engineering correlations.Out of recent experimental data, the measurements by Rausch et at.[2], carried out with a VTD under the saturated conditions, were found to show the best internal consistency over wide temperature range from 273 K to 363 K for all five selected HFEs.We note that our previous data collected with the single-sinker buoyancy method [6] show slightly different temperature slopes than other data for most HFEs.We suspect that this discrepancy occurred due to possible temperature gradients and convection in the relatively large liquid sample with volume of around 100 ml.On the other hand, the buoyancy method is not influenced by the sample viscosity, which may cause substantial errors in the data obtained with a VTD [19].The good agreement between the buoyancy method and the new VTD data in the vicinity of the laboratory temperature of 298 K, where the possible temperature gradients were the lowest, provides additional verification of the viscosity correction employed in Eq. 1 for relatively low-viscosity HFE fluids.Furthermore, the agreement of both measuring techniques close to 298 K and with the data by Rausch et al. [2] for most of the single-isomer HFE samples confirms the VTD calibration according to Prokopová et al. [20], which was extrapolated to rather high densities from 1300 to 1700 kg ⋅ m −3 .A preliminary, i.e., so far not officially published, multiparameter equation of state by Zhou and Lemmon [34] is available in REFPROP package v. 10 [10] for
Black dashed lines indicate the expanded relative deviation of Eq. ( 2) Fig. 8 Relative deviation of the Rackett-type correlation (2) for HFE-7500 from the densities taken from literature [2,3,6,36,38,41], new data, and 3M correlation [31].Black dashed lines indicate the expanded relative deviation of Eq. 2 HFE-7000.The predictions of the equation of state for the saturated liquid density are represented by the orange solid line in Fig. 4 and show quite good agreement with the new measurements in the temperature range from 273 to 303 K although our new data were not used to fit this equation of state.At higher temperatures, the equation shows an increasing deviation from the Rackett-type correlation (2), which follows the trend of the data by Rausch et at.[2].
Another preliminary multiparameter equation of state has been recently introduced for HFE-7100 (denoted also as RE449mccc) in the supplement of a publication by Huber and Lemmon [37].Unlike in case of HFE-7000, the equation of state follows the trend of the density data by Rausch et al. [2] over the entire temperature range as shown in Fig. 5. Similarly as shown in Fig. 3a, the influence of the isomeric composition of HFE-7100 on the experimental data can be clearly seen.The liquid density systematically increases with the increasing mole fraction of iso-isomer in the samples.The data with similar iso-isomer mole fraction of around 60 % to 62 % by Cendon et al. [24], Pineiro et al. [23], and Rausch et al. [2] agree well with each other.The new data with the mole fractions from 67 % to 100 % are shifted to higher densities.For some of the data sources, the isomeric composition could not be traced.However, from the trend of the data shown in Fig. 5, one can assume that the iso-isomer mole fraction could be around 60 %, 69 %, and 76 % in case of the data by Qi et al. [32], Tanaka [35], and Vinš et al. [6], respectively.Unfortunately, in case of the first batch (no.25584) measured in this work, the isomeric composition was not investigated either.One can assume that the iso-isomer mole fraction was approximately 75 %.Based on private communications, the samples measured by Muñoz-Rujas et al. [5] should have the iso-isomer mole fraction of around 52 %.However, the data show remarkably good agreement with other data with the iso-isomer mole fraction around 60 %.The possible composition of the samples employed by Shiflet and Yokozeki [36] is hard to judge due to the larger scatter of data.
A similar dependence of liquid density on isomeric composition can be seen in Fig. 6 for the other two-isomer component HFE-7200.A gradual increase in density can be seen with the increasing mole fraction of the iso-isomer.The data by Rausch et al. [2] and Muñoz-Rujaz et al. [25] with the iso-isomer mole fraction between 61 % and 62 % are in good agreement.The new data obtained in this work for the samples with an iso-isomer mole fraction between 67 % and 73 % are systematically higher by approximately 0.1 to 0.2 %.Based on the data shown in Fig. 6, one can again guess the isomeric composition of other data sources.The data by Fang et al. [38] and Pineiro et al. [23] seem to have an iso-isomer mole fraction of around 61 % due to the remarkably good agreement with the data by Rausch et al. [2] and Muñoz-Rujaz et al. [25].Our previous data obtained with the single-sinker buoyancy method [6] seem to have the mole fraction of around 72 %.
Figure 7 shows the density data for HFE-7300 compared to the Rackett-type correlation (2).As can be seen, all experiments are in very good agreement except for the different temperature slope in case of the single-sinker buoyancy data from the previous study [6], which was discussed above.The two batches of HFE-7300 specified in Table 2 show a slight mutual offset of about 0.5 kg ⋅ m −3 .As the batches have comparable purity, low water content and were handled in the same manner, the 139 Page 16 of 21 difference is assumed to be the batch dependency similar to other studies, e.g., by Sommer et al. [40] for toluene.In case of HFE-7300, the 3M correlation [30] provides relatively good predictions over the temperature range from 275 K to 345 K.
The density data for HFE-7500 compared to correlation (2) are provided in Fig. 8.The new data for batch no.21099 are in excellent agreement with the data by Rausch et al. [2] and Muñoz-Rujaz et al. [41] over the whole temperature range.The densities of the other two batches are slightly shifted by about 0.4 to 0.5 kg ⋅ m −3 which is considered to be a batch dependency as observed for HFE-7300.The data by Lafitte et al. [3] and Fang et al. [38] show only slight discrepancies which are, except for a single point by Fang et al. at 293 K, fully within the interval of the expanded relative deviation of the Rackett-type correlation (black dashed lines in Fig. 8).The singlesinker buoyancy data [6] and the data by Shiflett and Yokozeki [36] show larger deviations.Both datasets [6,36] have rather high expanded uncertainties of around 0.5 to 4.0 kg ⋅ m −3 .Their relevance was therefore lowered in the development of the density correlation (2).Besides, the weight w i of the single-sinker buoyancy data [6] was lowered to 0.1, as discussed above.

Other Effects Influencing Measurements with a VTD at 0.1 MPa
Due to the high sensitivity of the VTD used, additional factors affecting the density measurement could be examined.The high resolution of 0.001 kg ⋅ m −3 enables to inspect, for example, the gradual influence of sample degassing or the evaporation of two-isomeric samples at elevated temperatures.

Sample Degassing
As mentioned in section 2.1, the 5-ml liquid samples were degassed by applying repeatedly a slight vacuum in a 10-ml syringe.Our aim was to inspect the degree of degassing depending on the number of vacuum cycles and its influence on the measured liquid density.The samples, tempered inside a refrigerator at a constant temperature of 278 K, were taken from the 1-liter bottle, quickly degassed by different numbers of vacuum cycles in a syringe and applied directly into the VTD U-tube.The liquid density was measured at three different temperatures from 293 to 303 K. Figure 9 shows the observed variation of density depending on the number of degassing cycles for the two-isomer liquid HFE-7100 and the single-isomer liquids HFE-7000, HFE-7300, and iso-isomer of HFE-7100-iso with regard to the non-degassed samples.
Independent of the isomeric composition, almost identical density increase was observed for all samples taken from the bottle tempered at 278 K.A maximum increase of density of 0.75 kg ⋅ m −3 was observed after 10 degassing cycles, with the steepest change occurring after the first 4 cycles.The measured density did not change any further with increasing number of cycles for any of the samples including HFE-7100.This indicates that the degassing technique did not affect the isomeric composition of the two-isomer sample and the increase in density corresponds only to sample degassing.To verify this, an additional experiment with two samples of single-isomer liquids HFE-7000 and HFE-7100-iso tempered at the laboratory temperature of 297 K was performed.In this case, the degassing technique shows a similar trend, however, with a lower increase in density of around 0.5 kg ⋅ m −3 .This is considered to be due to the lower solubility of air in HFEs at higher temperature.
These experimental tests showed that regardless of the possible isomeric composition or the temperature at which the sample was degassed, the liquid density increased approximately by 0.40 kg ⋅ m −3 and 0.65 kg ⋅ m −3 after 4 degassing cycles (i.e., standard degassing approach described in Sect.2.1) at the degassing temperature of 278 K and 298 K, respectively.We note that the additional change in density due to further degassing cycles lies in the expanded uncertainty of the data presented.

Sample Temperature Before Its Dosing into the VTD U-tube
Another experimental test focused on the temperature of the sample and its handling prior to dosing into the VTD U-tube.Application of the liquid sample from a bottle into the densimeter using a syringe typically takes about 1 to 3 min, including degassing, flushing the U-tube with fresh sample, and capping the U-tube in-and outlet.Two-isomer mixture HFE-7100 (b.n.24865) and single-component HFE-7300 (b.n.20176) were measured at two different initial temperatures: once stored at the laboratory temperature of 298 K and once refrigerated at 278 K.The samples were not degassed in this case in order to speed up the sample handling.The density measurements at each storage temperature were repeated three times using the same procedure over the temperature range from 273 to 323 K.The density of the refrigerated samples was approximately 0.025 kg ⋅ m −3 lower compared to the warmer samples.This tiny difference, lying well within the expanded uncertainty of the measured density, is believed to be due to the higher amount of air dissolved in the colder samples.It follows that the quick sample handling and the initial storage temperature do not affect the accuracy of the obtained density data.The effect of exposure time to ambient air during the sample handling was inspected using the samples heated for 30 and 60 minutes in an uncovered beaker at a temperature of 308 K prior to dosing into the densimeter.For both HFE liquids, the density measured after 60 minutes was slightly higher compared to that after 30 minutes.The difference, which did not exceed a value of 0.040 kg ⋅ m −3 , appears to be due to the longer release of air dissolved in the liquid samples to the environment.On the other hand, a considerable difference was observed between HFE-7100 and HFE-7300 when comparing the quickly handled samples described in the previous paragraph with samples heated to T = 308 K for tens of minutes.In the case of single-isomer HFE-7300, the density of sample heated to T = 308 K was only 0.057 kg ⋅ m −3 higher than in case of quickly dosed samples with the initial tempera- ture of 298 K or 278 K.In contrast, the density of two-isomer HFE-7100 showed a noticeable increase of 0.275 kg ⋅ m −3 due to the heating of the sample in ambient air.Although it is difficult to confirm, it appears that this five times higher difference was caused by the change of composition during evaporation of the HFE-7100 samples rather than by a reduced content of dissolved air.
In summary, exposure of the sample to the ambient air must be kept as low as possible, especially when accurate and reproducible density measurements of liquid mixtures are to be performed using the sensitive barometric VTDs.

Conclusion
New data for the liquid density for five different hydrofluorethers were measured using a vibrating tube densimeter Anton Paar, model DMA 5000 M. The density data were measured at approximately 0.1 MPa over the temperature range from 273 K to the vicinity of the normal boiling point with an expanded combined uncertainty ( k = 2 ) of 0.13 kg ⋅ m −3 .Due to the high sensitivity of the employed VTD and its careful calibration according to the procedure introduced in previous work [20], several interesting effects influencing the measured density were investigated on different batches of HFE samples.HFE-7100 and HFE-7200 are binary mixtures of two hardly separable isomers, whose thermophysical properties have been considered identical so far.However, new experiments showed a systematic shift in the liquid density of HFE-7100 and HFE-7200 depending on the mole fraction of the isoisomer.In the typical range of iso-isomer mole fractions between 60 % and 100 %, the density varies by more than 5 kg ⋅ m −3 and 3 kg ⋅ m −3 in case of HFE-7100 and HFE-7200, respectively.Other experimental tests indicated the influence of sample handling before dosing into the VTD U-tube such as degassing, storage temperature, and exposure time to ambient air.
Based on the literature data for the low-pressure and the saturated liquid density and the new measurements, the Rackett-type correlation (2) was developed.The correlation provides good estimates for the saturated liquid density of all five HFEs.The expanded ( k = 2 ) relative deviation from the experimental data is lower than 0.2 % for all HFEs, except for HFE-7100 where the isomeric composition causes larger deviation.The new experimental data can be used in possible improvement of the preliminary multiparameter equations of state for HFE-7000 [34] and HFE-7100 [37] implemented in REFPROP [10], when especially the influence of the isomeric composition of HFE-7100 should be taken into account.
F NMR spectra (75.72 MHz, CDCl3) were measured using a 80 MHz instrument Spinsolve 80 ULTRA (Magritek, Germany) at a room temperature.The chemical shifts ( ) are given in ppm.As depicted in Figs. 1 and 2, signals at − 80.2 ppm (iso-) and − 86.6 ppm (n-) were used to determine the 139 Page 4 of 21

Figures 4 , 5 , 6 , 7 ,
and 8 compare the literature data and the new data for the liquid density at 0.1 MPa and the saturated liquid density of five selected HFEs with the Rackett-type correlation(2).The horizontal black dashed lines indicate the expanded relative deviation of the correlation given in Table et al. (2007) Qi et al. (2014) Vins et al. (2021) Ohta et al. (2001) @ p sat Rausch et al. (2015) @ p sat prelim.EOS -REFPROP v.10 @ p sat this work -b.n.20145

Fig. 9
Fig. 9 Variation of density depending on number of degassing cycles in a syringe for samples stored at the laboratory temperature 298 K and refrigerated at 278 K; densities measured with VTD at 293 K (a) and at 303 K (b)

Table 1
List of investigated hydrofluoroethers

Table 2
Specification, purity, water content, and isomeric composition of measured samples

Table 3
Average density of HFE-7000 sample no.20145 including the expanded uncertainties U( ) with k = 2 at the barometric pressure of 989.00 hPa a a Standard uncertainties:

Table 4
Average density of HFE-7100 samples including the expanded uncertainties U( ) at an average barometric pressure of 986.19 hPa Standard uncertainties:

Table 5
Average density of HFE-7200 samples including the expanded uncertainties U( ) at an average barometric pressure of 990.44 hPa Standard uncertainties:

Table 6
Average density of HFE-7300 samples including the expanded uncertainties U( ) at an average barometric pressure of 982.27 hPa Standard uncertainties: u

Table 7
Average density of HFE-7500 samples including the expanded uncertainties U( ) at an average barometric pressure of 986.16 hPa Standard uncertainties:

Table 9
Liquid density depending on the iso-isomer content in the HFE-7200 samples