Chemical looping combustion (CLC) of municipal solid waste (MSW)

Chemical Looping Combustion (CLC) has been found to be a better alternative in converting Municipal Solid Waste (MSW) to energy and has the potential to reduce the generation of dioxins due to the inhibition of the de-novo synthesis of dioxins. This study comprehensively reviews the experimental studies of CLC of MSW, the oxygen carriers, reactor types, performance evaluation, and ash interaction studies. Modeling and simulation studies of CLC of MSW were also critically presented. Plastic waste is MSW’s most studied non-biomass component in MSW under CLC conditions. This is because CLC has been shown to reduce the emission of dioxins and furans, which are normally emitted during the conventional combustion of plastics. From the several oxygen carriers tested with MSW’s CLC, alkaline earth metals (AEM) modified iron ore was the most effective for reducing dioxin emissions, improving combustion efficiency and carbon conversion. Also, oxygen carriers with supports were more reactive than single carriers and CaSO4/Fe2O3 and CaSO4 in silica sol had the highest oxygen transport ability. Though XRD analysis and thermodynamic calculations of the reacted oxygen carriers yielded diverse results due to software computation constraints, modified iron ore produced less HCl and heavy metal chlorides compared to iron ore and ilmenite. However, alkali silicates, a significant cause of fouling, were observed instead. The best reactor configuration for the CLC of MSW is the fluidized bed reactor, because it is easy to obtain high and homogeneous solid–gas mass transfer. Future research should focus on the development of improved oxygen carriers that can sustain reactivity after several cycles, as well as the system’s techno-economic feasibility.


Introduction
The increase in the volume of MSW generated and the threat to the ecosystem has led to more research on effective ways to solve the issue of processing our waste streams [1]. MSW consists of plastics, paper, textiles, food waste, garden waste, wood, metal and glass, as seen in Fig. 1 [2]. As the world population increases with the increase in economic and industrial development, there will not be enough landfills to meet the population demand and the demand for energy will eventually outweigh the supply [3]. Waste-to-energy technology is believed to help manage our municipal solid waste due to its ability to reduce greenhouse gas emissions and generate energy [4,5]. An effective waste management system must be environmentally sustainable, viable and generally acceptable [6]. Improper waste management can spread pathogens [7], water contamination [8], and soil and air pollution [9]. Different solid waste management processes have been studied to dispose off MSW effectively. Landfilling is the most common waste disposal method, especially in developing countries. It is an open dumping system that can lead to air, water and land pollution [10]. Also, this waste management system has high maintenance, transport and labor costs [2]. MSW has a heating value ranging from 8.5 to 23 MJ/ kg as analyzed in different literatures [2,[11][12][13][14] depending on the location, source and characterization, which makes it a good source of fuel for transportation, power generation and in powering equipment in petrochemical industries. Incineration, which is a type of thermal conversion and a source of energy that involves combusting solid waste at a high temperature in excess oxygen, has a lot of challenges which include high operating costs [15], corrosion of the combustion chamber [16], boiler fouling and presence of heavy metals and dioxins in incineration gasses [16].
Wang et al. [17] carried out a heavy metal analysis on the fly ash produced from the combustion of MSW in China and found that it contains large quantities of As, Cd, Cr, Cu, Ni, Pb, Zn, and Hg. The soils in the vicinity of the incineration plants were also tested and found to contain significant traces of these heavy metals [18]. Gabbar et al. [16] reviewed major heat treatment methods for MSW and discovered that landfilling and combustion are incompatible with the growth rate of MSW per year. Furthermore, while the combined pyrolysis-gasification process has the highest capital, operating and maintenance costs for MSW, it also has the lowest environmental impact [16].
Due to the challenges presented above from the different thermal methods of converting waste to energy, chemical looping combustion (CLC) has been found to be a better alternative in converting waste to energy and has the potential to reduce the generation of dioxins due to the inhibition of the de-novo synthesis of dioxins [19]. Chen et al. [20] reported that reducing chlorine and other heavy metal emissions is possible when a suitable oxygen carrier is selected. Chemical Looping combustion is a relatively new high-efficiency carbon capture and storage (CCS) technology that also proffers solutions to the high greenhouse gas emission by capturing CO 2 with low energy demand and cost penalty. Since CO 2 concentrations in the atmosphere have risen sharply in recent decades as a result of the world's reliance on fossil fuels for energy production, and global atmospheric CO 2 concentrations have risen from 280 to 390 ppm [21] in the early twenty-first century and has exceeded 400 pm in current times [22] and projected to be between 550 and 970 ppm at the end of the century [23]. CLC has been developed to produce a concentrated stream of CO 2 from industrial sources, transport it to a suitable storage location, and then store it away from the atmosphere for an extended period.
Presently, there is no comprehensive review that reports on CLC of MSW. This study comprehensively reviews the experimental studies of CLC of MSW, the oxygen carriers, reactor types, performance evaluation, and ash interaction studies. Modeling and simulation studies of CLC of MSW were also critically presented. Finally, research gaps were identified for future research directions. Lewis and Gilliland developed and patented a concept very similar to chemical looping combustion in 1954 [25]. The patent, titled "production of carbon dioxide," described the reduction of oxygen carriers in two interconnected fluidized beds using various fuels. The key of the process is that the oxygen used is derived from a metal oxide (M x O y ) and serves as an oxygen carrier [26].

3
The combustion process occurs in two interconnected reactors: the fuel and air reactor. The fuel reacts with the oxygen carrier in the fuel reactor to produce CO 2 and steam gases (reduction, reaction 1). The CO 2 -rich flue gas undergoes condensation and purification to achieve a highly concentrated CO 2 that is transported for storage [27]. While in the air reactor, the reduced oxygen carrier (M x O y-1 ) reacts with air and oxidizes to its original form (oxidation, reaction 2). Figure 2 shows the schematic diagram of a CLC of solid fuel with a Cu 2 O/CuO oxygen carrier [28]. The heat required during the reduction process in the fuel reactor can be supplied from the air reactor during the oxidation reaction [29]. Since the CO 2 produced is captured, no energy penalty is involved in separating the combustion gases [30]. Hence, the estimated cost of CO 2 sequestration in CLC (20 US$/ ton of CO 2 isolated from the atmosphere) is less than that of other clean combustion technologies (between 28 and 67 US$/ ton of CO 2 in precombustion, post-combustion and oxyfuel combustion) [31]. The sum of the reactions that take place in the fuel and air reactors is equal to the net combustion reaction (reaction 3) CLC process can have different reaction pathways for fuel conversion irrespective of the type of fuel used. In situ Gasification CLC (iG-CLC) occurs when fuel is gasified in the fuel reactor and the gaseous combustibles react directly with the oxygen carrier. This is the most common pathway for CLC. The other reaction pathway is the Chemical-Looping with Oxygen Uncoupling (CLOU) process which relies on the use of oxygen-carrier materials that release gaseous oxygen in the fuel reactor, allowing the solid fuel to burn with gas-phase oxygen [32]. Although the best reaction pathway is determined by the type of fuel, fuel gas concentration, reaction temperature and the reactivity of the oxygen carrier [33], however, Leion et al. [34] concluded that a higher char conversion rate is obtained from the CLOU process than that of the in situ gasification CLC process when copper oxide was used as an oxygen carrier for different types of coal, coke and wood char fuel.
CLC has been tested with different fuels; gaseous fuels (natural gas [35], methane [36], refinery gas or off-gas from steam reforming [36]), solid fuels (coal [37], biomass [38], petroleum coke [21] and other solid wastes (waste paper, plastics, etc.) [39]) and liquid fuels such as heavy oils [40]. As described by Wang et al. [28], for solid fuel CLC, the fuel undergoes a devolatilization process which releases volatiles and char. Simultaneously, the volatiles reacts with the oxygen carrier, and the char (mainly carbon) undergoes syngas gasification with steam and/or CO 2 to produce syngas (reaction 4 and 5). With steam as a gasification agent, a water-gas shift reaction also occur to produce H 2 and CO 2 gasses [41]. The intermediate gasification product then reacts with the oxygen carrier to produce an enriched CO 2 stream [42]. Although steam gasification has a higher gasification rate, the cost of generating steam is very high, which inherently increases the cost of CO 2 capture [43]. Due to this reason, Adanez et al. [44] suggested that the CO 2 from the flue gas after steam condensation can be partly recycled to the fuel reactor as part of the gasification reaction to reduce the amount of steam used for gasification, as seen in Eq. 5. The reduced oxygen carrier from the fuel reactor is then transferred to the air reactor, where it is re-oxidized by oxygen from air. In CLC systems, solid waste has been found to have higher overall reactivity than coal, and its char allows for faster complete burnout [45]. It also has a lower potential for carbonaceous material transfer to the metal/air reactor, where it would burn and emit CO 2 . (1)

Fig. 2
Example of a CLC configuration [28] Experimental studies of CLC of MSW IG-CLC and CLOU experiments have been tested for different solid fuels (coal [45] and biomass [46,47]) on a pilotscale years before the first experiment for MSW was published and has been found to be a promising technique. However, scaling up the process is quite challenging due to its low fuel conversion and CO 2 concentration in the fuel reactor. The unsatisfactory fuel conversion rate was caused by the disparity between the rate of char gasification reaction and the combustion reaction between the gasification products and oxygen carriers [48]. At the same time, the low CO 2 concentration in the fuel reactor is caused by the poor gas-solid interaction, agglomeration of the oxygen carrier particle cluster, etc., in the fluidized bed reactor [49].
The first experiment on CLC of MSW was published in 2006 by Cao et al. [50], where different solid fuels (coal, biomass and low-density polyethylene MSW) were compared based on their redox kinetics using copper oxide (CuO) as an oxygen carrier. The authors used wood and low-density polyethylene (PE) to study the performance of biomass and MSW. They concluded that MSW with high volatile contents showed excellent promise in the development of the chemical looping combustion process. Table 1 summarizes different  CLC experiments for MSW from 2006 to date. The table also presents the types of reactors used, oxygen carriers, objective and the inference observed from the experiments. Another type of waste that has been analyzed for the CLC process is biomass waste. Comparing different biomasses that have been analyzed, woodchips and sawdust had a high CO2 capture rate of > 90% [51] and a reduction in NO of up to 30% [52]. However, the aggressive ash in the samples is a difficulty with biomass waste. Pine sawdust contains 41% ash, with potassium being the most problematic key component [53]. On the other hand, this review will concentrate on non-biomass MSW, a relatively new solid fuel tested for CLC. Plastic waste is MSW's most commonly studied non-biomass component in MSW under CLC conditions [19,54]. This is because CLC has been shown to reduce the emission of dioxins and furans, which are normally emitted during the conventional combustion of plastics [55].

Different types of MSW studied under CLC conditions
As mentioned earlier, plastic wastes are the most common type of MSW studied under CLC conditions. These have (4) C(s) + H 2 O(g) → CO(g) + H 2 (g) ΔH 1073K = 134.9kJ/mol been investigated in order to determine the fate of heavy metals present in plastic waste (such as cadmium and chromium), the emission of dioxins formed from the presence of chlorine in plastics, and their reaction performance with various oxygen carriers. Plastic wastes such as polyvinylchloride (PVC) [54,56], polyethylene [50], polyurethane, and polypropylene [57] have been experimentally investigated under CLC conditions. A process simulation of CLC of various plastic wastes (polypropylene, polyethylene terephthalate, polystyrene, high-density polyethylene and low-density polyethylene) was performed by Yaqub et al. [58] and predicted their performance based on their CO 2 yield and combustion efficiency. Wang and Zhao [59] and Ma et al. [60] used a medical perfusion tube whose properties are similar to PVC for the CLC process. Other kinds of MSW investigated for the CLC process include pyrolysis gas-derived PVC waste [55], pyrolysis gas-derived MSW [61], syngasderived MSW [62], bottom ash from MSW [63] and waste paper [39]. MSW blends (waste paper and different plastics) [64] and a mixture of flour, paper, sawdust, cotton cloth, polystyrene, inert materials and non-combustible MSW to represent actual MSW [20] were also studied to evaluate the reaction performance and heavy metal transformation in the CLC process. Due to the heterogenous characteristics of MSW, the components of the solid waste are individually analyzed or a mixture of components with similar properties except for Chen et al. [20], where MSW of different properties were used. Although the authors did not mention the challenge faced with using the combination of the different MSW components, however, Strohle [24] believes combining the solid waste of different properties will lead to varied volatiles released which subsequently leads to varied gas composition at the outlet of the fuel reactor and incomplete conversion of the volatiles and gasification products. Nevertheless, solutions such as the addition of oxygen produced from an air separation unit to a post-oxidation chamber can be deployed. Another effective solution deployed by Hakandai et al. [65] is the hydrothermal treatment of the MSW prior to CLC, a form of pretreatment method. This process ensures the powdered MSW produced has a higher material uniformity and a higher carbon content and calorific value. This modification is also necessary to fit into the reactor to be used for the CLC process. Other pretreatment methods include but are not limited to sorting, leaching and mechanical size reduction. The capital cost for this pretreatment method is usually moderate and worth its benefit.

Reactors' configurations used for CLC of MSW
The CLC process can be carried out in different reactor configurations based on different reactor designs. It can be configured as two interconnected moving or fluidized reactors,  [65] packed or fluidized bed reactors, bubbling bed reactors and rotating reactors. The bubbling bed reactor also has a high solid inventory which is beneficial for high char conversion [43]. Most CLC setups have two loop seal devices usually placed between the reactors and the cyclone to prevent gas mixing between the two reactors [66]. For the CLC of MSW, the key reactor configuration investigated are (a) annular dual-type moving bed reactor, (b) dual batch fluidized bed [62], (c) semi-continuously operated fluidized bed [60], (d) two-staged pipe reactor [56] (e) gas-switching fluidized bed reactor [67] (f) fixed bed reactor setup [55] (g) fixed bed reactor system [20] (h) fluidized bed reactor [68]. The schematic diagram of these reactors is presented in Fig. 3.
Most of the CLC experimental reactor design used for MSW consists of single stage reactors except for Bi et al. [56] and Wang et al. [69], where two tubular reactors and two batch fluidized bed reactors were used, respectively. The tubular reactors used by Bi et al. [56] represented the fuel and air reactors. Nitrogen was used as the fluidizing gas in this experimental setup. However, for Wang et al., [69], two sets of tests were conducted simultaneously in the fluidized bed reactors. Reduction, purging and oxidation occurred in the reactors with water at 150 °C introduced as a gasification agent during the reduction process. Purging was done by introducing pure N 2 into the system to avoid contact with the oxidation and reduction gases.
Ma et al. [60] used a semi-continuously operated fluidized bed reactor. The interconnected fluidized bed reactor was the most commonly used configuration [70]. The interconnected fluidized bed reactor configuration continuously introduces the OC and plastic waste into the reactor via two screw feeders. The two screw feeders' rotation speeds can be precisely controlled to determine the feeding rate of plastic waste (corresponding to thermal power) and the feeding rate of fresh OC. The fluidizing gas used H 2 O and N 2 gas, similar to what was used by Wang and Zhao [19], Liu et al. [67] and Yaqub et al. [39] for the laboratory scale batch fluidized bed reactor for CLC of plastic waste and waste paper. The fluidized bed reactor ensures good mixing of the gas and solid carrier and easy circulation and replacement of the carrier material [71]. The solid particles leaving the reactors are recovered by a cyclone and sent back to the fuel and air reactor [30].
The moving bed reactor with an annular dual tube was used by Chiu et al. [57] for the CLC of PP and PU. In this setup, there are two solid inlets for the MSW and the oxygen carrier, designed as a screw conveyor for easy access into the reactor. O 2 and CO 2 were used as the gasification agent for the PP and PU MSW samples. The moving bed fuel reactor was attractive in maintaining complete fuel conversion and maximizing solid conversion [72]. Jiang et al. [58] used a fixed bed reactor to determine the dechlorination performance of PVC plastic waste. Apart from the main reactors in CLC, other components such as cyclones (to separate the entrained particles from the fuel reactor and air reactor), preheaters (to preheat air and fluidization gases) and filters (to further purify the CO 2 gas leaving the reactor) are added to the CLC setup. While preheaters and filters are necessary for all setups, not all have cyclones attached to them.
Also, since the reaction in the air reactor is highly exothermic during reoxidation of the oxygen carrier, excess heat can serve as a by-product and can be used for steam evaporation, preheating of air and fluidization gases even in the CLC setup thereby reducing the operating cost of the system. The CLC setup can also be integrated with another unit process to produce suitable by-products such as hydrogen and methanol to increase the economic revenue of the system. Hakandai et al. [65] introduced a methanol synthesis reactor to convert the CO 2 and H 2 produced from the CLC process to methanol and a combined cycle process for power generation. The process has been found to be feasible and competitive. Also, Miyahira and Aziz [73] integrated the Haber-Bosch process for NH 3 synthesis into the syngas chemical looping process of agricultural waste (rice husk) to produce ammonia which is utilized as agricultural fertilizer. Although the integration of the two processes shows a high energy efficiency, its economic viability has not been established.
For other solid fuels such as coal and biomass tested with the CLC process, the configuration of two interconnected fluidized-bed reactors with thermal inputs ranging from 0.5 kWth to 3 MWth have been built and operated [74]. In addition, a 25 kWth CLC unit with solid fuels was developed, with a moving bed as the fuel reactor and an entrained bed as the air reactor [75]. The three main types of bed reactors used for other solid fuels, as reviewed by Song and Shen [45], are bubbling bed, spout fluidized bed, and circulating bed due to their high char conversion and lower oxygen carrier requirements. These reactors are similar to what is operated for MSW.

Oxygen carriers reported in the CLC of MSW
The development of oxygen carriers is a significant challenge in the CLC process. An effective oxygen carrier must have the ability to do the following [76]: • High mechanical strength • Environmentally friendly • Cheap • Sufficient oxygen transport capacity • Good thermodynamic properties for fuel conversion • Highly reactive during the oxidation and reduction reaction 1 3 Fig. 3 Reactor configurations tested with CLC of MSW a Annular dual-type moving bed reactor b Dual Batch fluidized bed [62] c semicontinuously operated fluidized bed [60] d two-staged pipe reactor [56] e gas-switching fluidized bed reactor [67] f fixed bed reactor setup [55] g fixed bed reactor system [20] h fluidized bed reactor [68] Prior to CLC with MSW, Iron-, nickel-, copper-and cobalt-based oxygen carriers have been used commercially in CLC applications for solid, liquid and gas fuels [77]. Low-cost oxygen carriers are best used, because ash components in solid fuels reduce the oxygen carriers. Regeneration ability constantly needs to be changed [78]. For CLOU, oxygen carriers that can generate their oxygen capacity are commonly used. This mechanism is frequently used with CuO-Cu 2 O oxygen carriers, manganese, and cobalt oxides [78]. Also, combined oxides such as Fe-Co oxides [79], Fe-Mg oxides, Cu/Mn oxides [80], FeMnSiO 3 [81] and some perovskite oxides [82] are found to be effective as oxygen carriers under certain process conditions.
For MSW, iron oxides are the most common oxygen carriers used for the CLC process.  [83]. Since plastic wastes contain significant chlorine, an oxygen carrier with high chlorine resistance that can deactivate the chlorine present has been developed [56]. Single oxygen carriers, oxygen carriers with supports and a combination of oxygen carriers have been tested to achieve the desired property for chlorine resistance, complete carbon conversion and reduced emissions [30].
For single oxygen carriers, Hua and Wang [61] performed a simulation study to determine the effect of different oxygen carriers with CLC on the deacon reaction of pyrolysis gas of MSW. The deacon reaction (reaction 6) produces Cl 2 from the reaction of the oxygen carrier with HCl from the MSW pyrolysis gas. The MeO x and MeO y indicate the oxygen carrier in its oxidized and reduced state, respectively.
The formation of Cl 2 which is involved in the production of dioxins is believed to be reduced by the use of oxygen carriers compared to air. The oxygen carriers investigated include CuO, NiO, CaSO 4 , CoO, Fe 2 O 3 , Mn 3 O 4 , and FeTiO 3 . These oxygen carriers were compared with air used for conventional combustion based on their excess oxygen coefficient, reaction temperature, pressure, and tar influences.
Based on the excess oxygen coefficient, temperature and pressure, the highest amount of Cl 2 formed from the deacon reaction was found in air, followed by CuO, NiO, CaSO 4 , CoO, Fe 2 O 3 , Mn 3 O 4 and FeTiO 3 , respectively. Like air, CuO also produces molecular oxygen, generating a high amount of Cl 2 . This release mechanism makes it suitable for use in chemical looping oxygen uncoupling [84]. However, lattice oxygen is released for the other oxygen carriers, which makes it beneficial in deacon reaction (reduced amount of Cl 2 ). The authors also determined the effect of tar on the deacon reaction since pyrolysis gas from MSW contained tar of up to 0.1 mass fraction [85].
Likewise, Fe 2 O 3 was used as an oxygen carrier in order to detect the presence of Cl 2 in the reaction of the oxygen carrier with HCl [86]. The authors discovered that very little chlorine gas was produced with the major products being FeCl 2 and FeCl 3 between the temperatures of 700-900℃, as seen in reactions 7 and 8. Like Hua and Wang [61], Zhang et al. [86] discovered that only a minor amount of chlorine is produced when Fe 2 O 3 is used as an oxygen carrier. Hence dioxin emissions can be significantly reduced by using different oxygen carriers such as   For oxygen carriers with supports, Chiu et al. [57] used an iron-based oxygen carrier (Fe 2 O 3 ) supported with alumina (Al 2 O 3 ). This oxygen carrier is believed to enhance the utilization of oxygen present in the oxygen carrier when used with a moving bed reactor [87]. Combining this oxygen carrier with an annular dual-type moving bed reactor was able to achieve a complete carbon conversion at an oxygen carrier to fuel ratio of 1.86 and 6.56 for polyurethane and polypropylene, respectively.
Furthermore, 85 wt% iron ore (Fe 2 O 3 ) with different alkaline earth metals in the form of oxides and aluminates (BaO, CaO, MgO, BaAl 2 O 4, CaAl 2 O 4 and MgAl 2 O 4 ) were used as oxygen carriers for CLC of MSW-derived syngas to improve the reactivity of the iron ore. Based on the TGA, CLC performance evaluation in the batch fluidized bed reactor and the XRD analysis, the BaO support was found to have the best performance and highest lattice oxygen reactivity [62]. Another Fe 2 O 3 supported with CaSO 4 oxygen carrier was analyzed by Bi et al. [56]. This oxygen carrier was found to have a good heat stability at a temperature of 900 ℃ and complete conversion of the PVC pyrolysis gas was obtained at a fuel-to-oxygen carrier mass ratio of 8.

Experimental evaluation of the performance evaluation of CLC of MSW
The three main combustion performances which are usually analyzed with CLC of MSW are the oxygen carrier performance (oxygen demand), CO 2 capture and fuel conversion. The oxygen demand Ω n is the ratio of the oxygen required to oxidize the unburnt gas leaving the fuel reactor to CO 2 and H 2 O to the total oxygen required to oxidize the gas released from the fuel in the fuel reactor [88]. CO 2 capture η CO2 is the ratio of the gaseous carbon leaving the fuel reactor to the total carbon converted to gas in the fuel reactor [89]. The fuel conversion η F is the ratio of the carbon converted to gaseous compound in the air and fuel reactor to the total carbon added [31].

Reactivity of oxygen carriers
One of the main objectives of the CLC of MSW is to reduce the amount of choline emitted during the combustion process, which was found to produce dioxins, a persistent organic pollutant. Due to this, oxygen carriers have been modified to meet this demand. The redox performance of these oxygen carriers has been evaluated by different authors using (7) Fe 2 O 3(s) + 6HCl (g) → 2FeCl 2(g) + Cl 2(g) + 3H 2 O (g) thermogravimetric analysis (TGA) in order to determine the reactivity of the lattice oxygen present in the oxygen carrier.
Wang et al. [62] compared the mass loss rate of different modified oxygen carriers to determine the most reactive. Iron ore (IO) modified with alkaline earth metal (AEM) oxides (BaO, CaO, and MgO) and alkaline earth metal aluminates (BaAl 2 O 4 , CaAl 2 O 4 , and MgAl 2 O 4 ) were compared using MSW-derived syngas as fuel. The analysis showed that the AEM oxides had better reactivity than the AEM aluminates. The iron ore modified with Barium oxides (BaO) showed the best performance in improving the iron ore activity. Also, iron ore doped with HCl sorbent was analyzed to determine the oxygen carrier's reactivity for HCl removal from MSWderived syngas. The author observed that the iron ore without the doping could not efficiently remove the HCl due to an unfavorable thermodynamic reaction between the Fe 2 O 3 and HCl [90]. In general, the Ba alkaline earth metal showed the highest reactivity, followed by Ca, then Mg when modified with iron ore.
Similarly, modified AEM with CuO-Al 2 O 3 was also analyzed at different weight ratios by Liu et al. [91]. Except for that with barium, the other modified oxygen carriers had a better oxygen transport capacity. In essence, barium oxide or aluminate has a better oxygen transport capacity when mixed with iron oxide than copper oxide.
Other  [92]. In both cases, the modified oxygen carriers were found to have a higher reaction rate than the pure oxygen carriers. However, the CaO/K 2 O/Na 2 O-decorated Fe 2 O 3 /Al 2 O 3 hinders the transfer of active lattice oxygen in OC particles. This could be due to the modified oxygen carrier's larger surface area, which impedes the contact of the oxygen carrier with the reactants. Alkali metal oxides such as BaO modified with the Fe 2 O 3 /Al 2 O 3 give a better reactivity, as analyzed by Wang et al. [62].
The oxygen transport capacities of some modified oxygen carriers used for CLC of MSW are summarized in Table 2. Compared to modified oxygen carriers, the oxygen transport capacity of pure metal oxides is from 0.01 to 0.2 [93]. In summary, CaSO 4 and oxygen carriers mixed with CaSO 4 have the best oxygen transport capacity and are highly reactive. However, this oxygen carrier has a low regeneration ability of about 64.6% after just six cycles due to possible side reactions during oxidation to produce CaO (reactions 9-12) (9) CaSO 4 + CH 4 → CaS + CO 2 + 2H 2 O (reduction) (10) CaS + 2O 2 → CaSO 4 (oxidation)

Combustion efficiency
Combustion efficiency is another performance parameter that can be used to measure the reactivity of the oxygen carriers. For most CLC of MSW experiments, the combustion efficiency was compared for various oxygen carriers. Wang et al. [62] compared the iron ore modified with AEM oxides and aluminates based on their CO and H 2 combustion efficiencies for CLC of MSW-derived syngas. While a higher CO combustion efficiency was obtained compared to the H 2 combustion efficiency due to the weaker bond strength of H 2 [94], the modified oxygen carriers had a higher combustion efficiency in the range of 80-100% and that of plain iron ore in the range of (45-75%). In conclusion, iron ore modified with the AEM oxides showed higher combustion efficiency for MSW-derived syngas than that with the AEM aluminates due to their stronger interactions with the iron oxide and the more stable properties of the aluminate [95].
However, a different trend was observed for the CLC of plastic waste by Wang and Zhao [92]. The combustion (11) CaS + 3∕2 O 2 → CaO + SO 2-(oxidation side reaction) (12) CaS + 3CaSO 4 → 4CaO + 4SO 2 (oxidation side reaction). efficiency when plain iron ore was used was higher than that of the different modified iron ore used. The authors believed it could either be due to diffusion limitations in the experiments or the adsorbent decoration hindering the transfer of active lattice oxygen. Other factors such as decoration methods and temperatures, were also compared to determine the best combustion efficiency. The physical mixture decoration method showed the best combustion efficiency compared to wet precipitation and coprecipitation methods. And the lowest temperature of 850 °C had the highest combustion efficiency. It should, however, be noted that even the lowest efficiency was greater than 90%. The authors also compared the CLC process (using the undecorated iron ore) with the conventional incineration method, and a higher combustion efficiency was observed with the conventional incineration [68]. The plastic waste CLC process produced a combustion efficiency greater than 90%, which means it is equally able to attain a highly efficient energy utilization.
Other factors such as the volume flow rate of the fluidizing agent, the mass flow rate of the oxygen carrier and the effect of Cao decoration were analyzed by Ma et al. [60] to evaluate the combustion efficiency of CLC of plastic waste. Using the CaO-decorated iron ore, oxygen carrier generally resulted in a combustion efficiency greater than 90%. Increasing the volume flow rate of the fluidizing agent reduced the combustion efficiency, while increasing the mass flow rate of the oxygen carrier increased the combustion efficiency. This is because the higher superficial fluidization velocity means less bed inventory; thus, less active oxygen was provided [19].

CO 2 yield
The CO 2 yield is the ratio of CO 2 concentration to the total carbon concentration in the FR flue gas. A high CO 2 concentration in the concentration profiles signified a relatively high CO 2 yield. However, the mass flow rate of the oxygen carrier, fluidizing velocity and the volume flow rate of the fluidizing agent could also affect the CO 2 yield. While increasing the fluidizing velocity reduces the residence time, which leads to a reduced CO 2 yield from 97.8 to 97.2%, increasing the mass flow of the oxygen carrier and the fluidizing steam increases the CO 2 yield from 85 to 98% [19,60]. For PU and PP plastic waste, an optimum oxygen carrier to fuel ratio of 1.86 and 6.56, respectively, was found to give an almost 100% CO 2 yield when an alumina-supported iron-based oxygen carrier was used in the CLC experiment [57]. The higher oxygen carrier flow rate used in PP is due to the higher carbon and hydrogen in PP plastic waste. In conclusion, the increased CO 2 concentration and low CO and CH 4 obtained in the concentration profile signify a high CO 2 yield for the CLC of MSW.

Carbon conversion
Carbon conversion is the measure of the mole of carbon in the flue gas to the mole of carbon added to the reactor. In other words, any residual char combustion in the air reactor will reduce the amount the carbon conversion in the CLC system. The use of CaO decorated and/or alumina-supported iron ore for CLC of the medical perfusion tube [19], PP and PU plastic waste [57] resulted in a high carbon conversion (80-98%). Hence, a sufficient oxygen carrier must be used to completely convert all the carbon present in the waste sample to obtain an almost complete carbon conversion. However, when ilmenite was used as an oxygen carrier for PVC plastic waste, carbon conversion of about 50% increased to approximately 85% when the temperature increased from 800 to 950 °C [39]. Also, the same authors used waste paper as a fuel and carbon conversion greater than 90% was obtained. The increase in carbon conversion is attributed to the high volatile content in waste paper compared to PVC waste. The increase in carbon conversion, temperature, mass flow rate of oxygen carrier and modified oxygen carrier with the ability to transport lattice oxygen was found to be the significant factors affecting the carbon conversion. Adanez et al. [31] and Ma et al. [60] analyzed all these operating parameters.
The maximum conversion rate, another performance tool analyzed, is similar to the carbon conversion and measures the gasification rate per unit of the non-gasified carbon in the  [64] reactor. Since this is similar to carbon conversion, the same trend is obtained, and the same factors that affect carbon conversion also affect the conversion rate.

Phase characterization
Since the oxygen carrier gets re-oxidized and reduced for several cycles when MSW is introduced into the reactor, there is a need to characterize and compare the oxygen carrier before and after the completion of the CLC experiment. This will determine if a new organic compound is absorbed by the oxygen carrier, which might affect the reactivity of the oxygen carrier. The X-ray diffraction (XRD) analysis indicates the active components present in the solid sample. This can also be used to determine if there are ash deposits on the oxygen carrier, which can cause the deactivation of the oxygen carrier [96]. The oxidation and reduction phase of the oxygen carriers obtained from the XRD analysis is summarized in Table 3.
The AEM-modified iron ore oxygen carrier XRD showed a conversion from Fe 2 O 3 to Fe 3 O 4 and FeO after the reduction of the pure iron oxide. The fresh AEM oxides observed in the fresh oxygen carrier disappeared after ten reduction cycles, and AEM ferrites were formed due to the mixture of the AEM and the iron oxides. The AEM ferrites showed superior reactivity in chemical looping processes, which was ascribed to the large amount of lattice oxygen associated with Fe [97]. However, the AEM aluminates were stable for both reduced and oxidized states. Hence, a similar XRD was observed. For the CaSO 4 oxygen carrier analyzed by Bi et al. [54], the CaSO 4 was the only component observed from the XRD before the CLC process, and the reduced form of the oxygen carrier contains CaS and CaSiO 3 . For Na, K, and Ca decorated natural iron ore oxygen carriers used to determine the dechlorination performance of CLC of PVC, different K, Na and Ca chlorides were observed after the fifth redox cycle, which would eventually decompose to form Cl 2 when exposed to the atmosphere. The dechlorination products signify a good dechlorination efficiency. However, the presence of Ca 3 Al 2 (SiO 4 ) 2 Cl 4 and Ca 2 SiO 3 Cl 2 indicated that as the reaction progressed, part of Ca tended to form inert substances with Si/Al in the oxygen carrier and lost its dechlorination ability [55]. The crystalline chlorides were not detected after several redox cycles for the oxygen carriers with high chlorine plastic samples, probably due to low contents or amorphous structures [67]. The XRD analysis of the oxygen carrier of a mixture of CuO, MgO, Al 2 O 3 and BaCO 3 or SrCO 3 , which was used for the CLC of syngas derived from MSW [67], is presented in Fig. 4. The calcination of the mixture resulted in the production of the Fig. 4 Phase composition of a XRD pattern of fresh Cu-Mg-Al-Br/Sr oxygen carrier b XRD pattern after five and 20 cycles [67] different organic compounds observed (Fig. 4a). Comparing the XRD analysis of the different oxygen carrier composites with the ones obtained after 5 and 20 cycles showed some peaks nearly disappearing (Fig. 4b). The reduction in the Cu 2 MgO 3 peak could result from the migration of Cu to the surface of the solid sample during the redox cycles, which led to the uneven distribution of Cu/CuO and limited the dissolution of CuO into the complex oxide Cu 2 MgO 3 [98].

Impurities and ash from CLC of MSW
The CLC technology, owing to its carbon capture abilities, has significantly contributed to the reduction in greenhouse gas emissions, making the process more environmentally friendly [78]. For CLC of MSW, chlorine [92], dioxins, heavy metals and sulfur emissions [20] were studied [55]. Since plastic waste was mostly studied, chlorination efficiency and the effect of oxygen carriers on intermediate products of dioxins such as chlorine, HCl and chlorobenzene were analyzed.

HCl, Cl and PCDD/F's emission
PCDD/Fs are formed in all thermal processes when chlorine, oxygen, hydrogen and carbon are present [99]. Chlorine (Cl), which can form acidic pollutants, is the key element in the formation of dioxins, with PVC plastic waste being the primary Cl source in MSW [100]. The dioxin can be inhibited by suppressing the deacon reaction, which can be inhibited by suitable oxygen carriers, temperature or amount of steam. The interaction between HCl present in MSW and iron ore (Fe 2 O 3 ) was analyzed to mimic a CLC process, and the effect of steam on the chlorine gas quantity produced during the reduction process was investigated. The amount of chlorine was measured using a methyl orange spectrophotometric method described by Zhang et al. [86]. At a CLC temperature of between 700 and 900 °C, increasing the amount of steam added to the CLC process was found to reduce the amount of chlorine gas produced [86]. The oxygen carrier was also found to absorb the HCl with iron chloride gas formed at this temperature based on Eq. 13. The use of CaSO 4 /Fe 2 O 3 was also found to absorb the HCl present in PVC plastic waste to produce Ca 2 FeO 3 Cl, as seen in the XRD in\*MERGEFORMAT Figure f. However, the formation of this Ca 2 FeO 3 Cl indicated a decreased regeneration of the CaSO 4 /Fe 2 O 3 oxygen carrier [56].
Dechlorination efficiency was analyzed when K, Na, and Ca decorated iron ore was used as an oxygen carrier for medical and PVC plastic waste. This was calculated as a measure of the ratio of the flue gas's total chlorine content to chlorine's total molar content in the plastic waste, which was measured using an ion chromatograph. The three decorated iron ore oxygen carriers analyzed with the medical plastic waste showed a dechlorination efficiency greater than 65%, with CaO-decorated iron ore having the highest dechlorination efficiency [92]. However, for the PVC plastic, CaO had the lowest dichlorination efficiency at 45%. Among the three decorated iron ores analyzed, CaO was found to have the highest activation energy during its reaction with the HCl gas from the synthetic pyrolysis gas. This led to a lower reaction rate and hence a lower dechlorination efficiency, as obtained by Jiang et al. [55] (See Fig. 5).
It is believed that the significant difference between the dichlorination efficiency of CaO decorated and NaO and KO could be that from the reaction with HCl, CaCl 2 had a substantially higher volume than KCl and NaCl produced from the same quantity of HCl, which promoted its buildup on the OC's surface after synthesis and hampered HCl diffusion to its interior pores. Wang and Zhao [92] also believed that the close chlorination efficiency obtained with the medical plastic waste was due to the intrinsic reactivity of adsorbent with HCl, the mass and heat transfer under the atmosphere of fluidized bed reactor and physical properties such as surface area and pore structure when these adsorbents were decorated with Fe 2 O 3 /Al 2 O 3 OC particles. Also, increasing the temperature from 850 to 925 °C favored the dechlorination efficiency. However, this led to the decomposition of methane, which resulted in the deposition of more carbon (less combustion efficiency). Like the CaSO 4 /Fe 2 O 3 oxygen carrier, the decorated oxygen carrier regeneration ability decreases as the redox cycle increases for both dechlorination efficiency research papers [55,92]. This has led to up to a 65% reduction in dechlorination efficiency after about 30 redox cycles [92]. As observed in Table 1, the chlorine present in the plastic waste gets absorbed by the AEM oxides after several cycles, resulting in a reduced regeneration ability.
Furthermore, a detailed thermodynamics analysis of the chlorine interaction with iron oxide and ilmenite showed a high concentration of HCl. Comparing the two oxygen carriers, iron oxide produced a lower HCl concentration, while ilmenite produced a large amount of HCl. As seen in [55,56,92], using modified iron ore was found to reduce the HCl concentrations. However, this led to the production of calcium and alkali chlorides which led to the formation of slag that causes corrosion of the bed material.
In summary, CLC can potentially reduce the formation of dioxins in chlorine containing MSW such as PVC, compared to pyrolysis, as analyzed by Bi et al. [54]. Moreover, modified oxygen carriers have a better dichlorination efficiency than single oxygen carriers. On the other hand, modified oxygen carriers promote the production of alkali chlorides on the reactor bed, which not only decreases the oxygen carrier's regenerative potential but also causes bed material degradation.

Alkali interactions with oxygen carriers
Common alkali and alkali earth metals present in high concentrations in MSW ash are Ca, K and Na [101]. During the CLC process, these metals can react with silicates present in some oxygen carriers or in the ash, forming alkali silicates in the form of vicious melts and binding the bed particles together. This can lead to bed agglomeration and defluidization [102]. Less work has been done on analyzing different oxygen carriers used with MSW and their interactions with its ash. Stanicic et al. [103] discussed in detail the interactions of the alkalis in MSW ash with ilmenite and iron oxide carriers. The authors discovered that fewer alkali chlorides (KCl and NaCl) are produced with ilmenites than iron oxide. K 2 O and Na 2 O are also formed for both oxygen carriers but in small quantities and tend to reduce with an increase in ash content. Also, as explained in the previous section, a high amount of potassium aluminate silicates is produced with iron oxides (K 2 Al 2 Si 4 O 12 ) and ilmenite (KAlSi 3 O 8 ). KAlSiO 4, observed in the XRD phase characterization of the AEM-modified iron ore with MSW syngas [55], was also observed from the thermodynamic calculation in relatively smaller quantities. For Na, NaAlSiO 4 at high concentration is observed with KAlSi 3 O 8 in minimal concentrations. In summary, it can be seen that both K and Na do not interact identically with oxygen carriers, and the potassium aluminum silicate is majorly in the leucite and feldspar phase, while that of sodium aluminum silicate is in the nepheline phase [103].

Heavy metals interactions with oxygen carriers
MSW contains a relatively high amount of heavy metals that are highly harmful to the natural environment and human health compared to other solid fuels (coal and biomass) [104]. In addition to the common alkali and alkaline earth metal compounds, studies have shown that the combustion of waste-derived fuels in fluidized bed boilers may increase trace elements in the fly ashes [105]. As a result, heavy metal emissions are one of the CLC's challenges and concerns. FactSage 5.3.1 software was used to calculate the equilibrium distributions of heavy metals during the chemical looping gasification of MSW by Cai et al. [106]. The authors explored the transformation and migration of heavy metals such as Pb, Cd, Zn, Cr, and Cu in calcium-based CLG using the optimal operating condition of Ca-CLG (equivalence ratio (ER) of 1.2, a mass ratio of steam to carbon (S/C) of 2, and a mass ratio of calcium to carbon (Ca/C) of 2). The authors concluded that with the exception of Pb, the other heavy metals could be stabilized into solid compounds during gasifier operation temperature of 600-750 °C. Pb, however, could convert into solid sulfides if sulfur was present in the MSW. The distribution of Pb is similar to what was observed by Stancic et al. [63].
The fate of Zinc, Copper and Lead during oxygen-aided combustion was also studied by Stanicic et al. [107], with ilmenite as an oxygen carrier. Four MSW ash samples were characterized, and it was discovered that iron on the surface of ilmenite particles interacts with copper and zinc present in the MSW fly ash to form ferrites, CuFe 2 O 4 and ZnFe 2 O 4 . Lead, however, ended up as condensed PbCl 2 in the fly ash, but mixed oxide PbTiO 3 was identified at the oxygen carrier surface. Although the oxygen carrier has been able to absorb the metals from the ash, this reduces the oxygen carrier's reactivity and life span. However, these Pb, Zn and Cu compounds were slightly different from what was obtained from the fact stage thermodynamic database calculation, as expected. More of Zn 2 SiO 4 and less of ZnFe 2 O 4 was obtained, Cu 5 FeS 4 Cu 2 O and Cu solids were obtained with copper and PbS, Pb, PbO gas and Pb(s) and Pb 2 FeSi 2 O 7 at high ash concentration of about 20-60% in the MSW.
Several phases of chlorides, alkali and heavy metal interactions were presented based on experimental characterization and thermodynamic calculations. Dissimilar results were expected in some cases due to the limitations in software calculations, such as isothermal conditions. However, an important thing to note is the formation of chlorides due to the high chlorine present in MSW which can lead to the formation of dioxins, a toxic pollutant and a high amount of alkali silicates which can lead to corrosion and fouling of bed materials.
However, Chen et al. [20] introduced an innovation by combining CLC and CLG in order to remove the heavy metals absorbed by the oxygen carrier. Cadmium (Cd), primarily distributed in fly ash due to the generation of the reducing gas during CLG based on copper and iron-based oxygen carriers, was used to test the process. The concentration of cadmium in the OC particles grew linearly with the number of cycles, from 7.1 mg/kg of MSW to 33.3 mg/kg, with an average capture efficiency of 85%. In contrast, the high concentration of cadmium in the OC particles could be removed efficiently after just one cycle of the CLG process. The implication of this additional unit operation in terms of cost and profitability needs to be explored.

Modeling and simulation of CLC of MSW
Design, optimization, and scale-up efforts benefit from mathematical modeling of the reduction and oxidation reactions inside CLC reactors. CLC simulation primarily involves reactor fluid dynamics, reaction scheme, reaction kinetics (changing grain size model, shrinking core model, nucleation and nuclei growth models), reactor residence time distribution, and process simulation [108]. Because of its extensive physical and thermodynamic property data banks and fully developed modules, the Advanced System for Process Engineering (ASPEN Plus ® ) is widely used in CLC simulation. However, Chemcad software has also been used for simulation for MSW [58] and other solid fuels such as coal [109] and biomass [110].
Hua and Wang [61] compared the performance of a CLC MSW process with conventional MSW incineration to determine the deacon reaction activity with different oxygen carriers. This was analyzed using ASPEN plus software, and the thermodynamic analysis reveals that the amount of Cl 2 oxidized by the seven oxygen carriers studied in the deacon reaction is less than that oxidized by air. The results also showed that the activity of lattice oxygen in the deacon 1 3 reaction is lower than that of molecular oxygen. Two types of CLC processes (IG-CLC and CLOU) were analyzed by Yaqub et al. [58] with MSW and compared with coal. Chemcad software was used to predict their performances and the process simulation demonstrated that using MSW has a solid fuel in CLC and has an equal (IG-CLC) and better (CLOU) CO 2 capture efficiency and combustion efficiency than coal. The MSW (waste paper and plastics) was also blended, and the results showed that the IG-CLC process had a higher CO 2 yield (higher degree of CO 2 capture) than the CLOU process (30-80 percent) for the individual waste paper and plastic waste samples and the waste paper/plastic blends [64]. The CLOU process had marginally higher combustion efficiencies for all the different waste plastics and paper than the IG-CLC process. In comparison, the IG-CLC process had higher combustion efficiency (30-75 percent) for blends than the CLOU process (25-70 percent).
However, it was observed that only process simulation has been used to predict the performance of CLC had been done for MSW. Numerical simulation, reactor modeling, the reaction kinetics of oxygen carriers and computational fluid dynamics are lacking for MSW fuel. This is necessary in order to characterize the system's fluidization and chemical kinetics [111] and can be used in the future to develop guidelines for optimal unit operation [31].

Challenges and future outlook
The general key challenge faced with the CLC of solid fuels is the incomplete conversion of char in the fuel reactor. This leads to a high concentration of unreacted char in the bed of the fuel reactor [43]. This results in the unreacted char being circulated together with the oxygen carrier to the air reactor, which reduces the CO 2 capture rate. Solutions such as the introduction of a secondary fuel reactor were proposed by Gayan et al. [112]. Other solutions were proposed, such as reducing the interaction between the ash from solid fuels and oxygen carriers by magnetic separation [113].
However, one major challenge for MSW is the interaction between oxygen carriers and MSW ashes during prolonged exposure. This has been found to lead to the deactivation of oxygen carriers due to agglomeration, attrition and carbon deposits [96]. Hence, the focus should be on ash content on the type of solid fuel, optimum experimental conditions and oxygen carrier composition in order to minimize these challenges [114]. Since the ash is usually deposited on the oxygen carrier, separating ash from the oxygen carrier is another challenge, and this separation's effectiveness has received little attention. Also, tar formation must be extensively researched, especially from plastic waste produced during pyrolysis. This is because the undesired tar can clog, foul, and corrode downstream pipes [115]. Also, studies on phosphorus interaction with oxygen carriers have not been well analyzed. Although, compared to coal and biomass, MSW has a smaller phosphorus concentration, and most XRD analysis has not been able to identify phosphorus compounds in the oxygen carrier [62,63].
While CLC has been found to be a promising technology in converting waste to energy, research on finding optimal conditions to minimize emission levels and maximize combustion performance needs to be prioritized. Pilot-scale chemical looping process demonstrations can serve as essential foundations for the future of MSW chemical looping processes. Further research should include combining the kinetic data of MSW with the fuel and air reactors, which will allow the design of reactors optimized for the MSW conversion and dynamic simulations of the CLC system.
While using the different reactors has shown positive results, some limitations were observed with some of the reactors. These limitations are, however, not specific to MSW samples. For interconnected fluidized bed reactors, gas leakages usually occur between the fuel and the air reactor [116]. This can be minimized by connecting another fuel reactor which serves as a carbon stripper, and a loop seal that connects the carbon stripper to the air reactor [43]. This has been implemented in a 50 kWth CLC unit by Ma et al. [117]. Also, the bubbling bed fuel reactor was found to have a little gas-solids reaction due to the low solids circulation rate [118]. This challenge was overcome by increasing solid inventory in the fuel reactor [42]. It is believed that these solutions can also be considered for the CLC-MSW process.
Furthermore, it is critical to conduct research to improve the adaptability of oxygen carriers (long-life oxygen carriers), while maintaining reactivity and structural integrity over multiple redox cycles. More importantly, focusing on the economic conversion of MSW to high-value chemical products and liquid fuels would hasten the commercialization of the MSW CLC process on a large scale. Although Mohn et al. [119] investigated the economic potential of converting waste to energy with CLC, additional experimental calculation needs to be implemented in order to determine the feasibility of the process such as revenue from the negative emissions of biogenic components of MSW. Additionally, research on the CLOU of MSW needs to be studied. Compared to iG-CLC, there is a significant difference in the degree of development of this process.
Finally, these challenges mentioned above have made the commercialization of the CLC of MSW difficult. To proceed with upscaling, total confidence in the oxygen carrier employed for the CLC of MSW must be established.

Conclusion
MSW is an important energy source; further research into its conversion to energy will reduce our reliance on fossil fuels. Given its carbon neutrality, significant environmental benefits are expected as this can provide clean, renewable energy solutions to reduce net GHG emissions. As discussed in this review, the CLC of MSW has received a lot of attention, because it has the potential for providing a sustainable path to decarbonized energy and management of MSW. The performance of CLC of different MSW types was reviewed, and this conversion pathway has been found to be a promising technology.
Different types of MSW reviewed in this manuscript include plastic waste (polyvinylchloride (PVC), polyethylene, polyurethane, polypropylene, polyethylene terephthalate, polystyrene, high-density polyethylene and lowdensity polyethylene), waste paper, MSW blends (waste paper and different plastics), a mixture combustible MSW, inert materials and non-combustible MSW to represent actual MSW and MSW-derived syngases. From the different types of reactor configurations used for CLC of MSW (annular dual-type moving bed reactor, dual batch fluidized bed, semi-continuously operated fluidized bed, two-staged pipe reactor, gas-switching fluidized bed reactor, fixed bed reactor system and fluidized bed reactor), the fluidized bed reactor is the most often utilized reactor configuration because it is easy to obtain high and homogeneous solid-gas mass transfer.
Suitable oxygen carriers such as AEM-modified oxygen carriers have been found to be ideal for reducing the quantity of HCl produced, thereby reducing dioxin emissions. Also, improved combustion efficiency and increasing carbon conversion were obtained using modified oxygen carriers compared to single oxygen carriers. The challenge of ash interaction with oxygen carriers and the phase characterization of different oxygen carriers before and after CLC experiments was presented. The XRD analysis performed on the oxygen carrier showed that the deposits of some of the heavy metals from MSW ash affect the combustion efficiency and dichlorination efficiency due to its deactivation after several cycles and can induce corrosion and fouling of bed materials. The development of better oxygen carriers that can maintain reactivity after several cycles and the economic feasibility of the system need to be studied in the future.
Funding Open access funding provided by University of Johannesburg.
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http:// creat iveco mmons. org/ licen ses/ by/4. 0/.