The influence of convection drying on the physicochemical properties of yacón (Smallanthus sonchifolius)

Yacón root is a natural source of fructans, which has many potential benefits. Convective drying has been applied to increase the shelf life of yacón roots. However, this processing may lead to detrimental effects on the physicochemical functionality. The drying was investigated using different conditions (drying temperatures of 45 °C, 50 °C and 55 °C at a drying air velocity of 2 m/s and 60 °C at a drying air velocity of 2 m/s, 3 m/s and 4 m/s). The dried samples were compared to the original yacón with regard to their physicochemical properties. From all the properties that were studied, the color of the dried material and the elastic modulus of the reconstituted yacón were the most important properties being minimized respectively. The results of this investigation indicate that the best drying conditions, where the physicochemical properties of the samples are kept closest to the original material, are obtained either by using temperatures of 55 °C and 2 m/s or using higher temperatures but increasing the air velocity.


FOS Fructo oligosaccharides X aq
Free moisture m aq The amount of water remaining after drying at a certain time ms Total solids in the sample DM Dry matter WIS Water insoluble solids WSS Water soluble solids d 32 Surface-weighted mean of the particle size d 43 Volume-weighted mean of the particle size

Introduction
Improved healthy aspects of food products is a well established trend in the food industry, and one of the identified aspects is the need to enhance the intake of dietary fibers. Dietary fibers are defined as polysaccharides and lignins that are non-digestible in the intestinal tract. These components provide different functional properties when applied in food products as they can modify or improve the texture and shelf life of foods [1].
One of the components of dietary fibers, the inulin-type fructans, has received particular attention due to their ability to interact with the texture properties of food products [2,3]. Inulin-type fructans are linear poly carbohydrates consisting of β (2 ← 1) fructosyl-fructose linkages [4]. They provide properties such as the ability to increase the absorption of calcium and magnesium [5]. They also present prebiotic properties due to their capacity to stimulate the growth of beneficial and decreasing the growth of harmful bacteria in the intestine [6].
Yacón (Smallanthus sonchifolius) is a natural source of inulin-type fructans, and it grows in the Central Andean regions limiting with the Amazon basin between 1800 and 3500 m above sea level, and it is cultivated especially in countries like Bolivia, Peru, Ecuador, and Argentina. Yacón, a member of the sunflower family (Asteraceae), is a perennial plant that grows up to 1.5 to 2.5 m and produces large tuberous roots. The roots have different tissue colors: white, yellow, orange, and purple depending on the variety of the plant and the region where it grows [7].
Fruits and vegetables that are dried change many quality properties like the loss of vitamins and other nutrients, alterations in color and texture, density and porosity but these losses are highly dependent on the condition and the method of drying [8]. The shrinkage and toughness of the dried product are increased when the drying of the product is extended possibly leading to reducing rehydration capacity [9]. The effect in the rehydration capacity is possibly produced because the water loss creates cracks when leaving the drying material that produces structural damage in the food material [10].
Convection drying is a drying process in which the material receives heat from the air flow. The increase of the temperature in the material is related to the difference between the temperature of the air flow and the surface of the material. Convection drying presents advantages like providing control of the temperature of drying. However, the problem is when the drying reaches a low amount of moisture in the material, the rate of moisture loss begins to decrease and the rest of the drying time that can be long is spent trying to eliminate the last remains of moisture [9].
The objective is to describe the sensitivity of the physicochemical functionality towards the drying parameters of convective drying of yacón.

Preparation of yacón paste
The measurement devices and accessories used during the experiments and their technical specifications are given in Table 1.
Yacón roots with orange tissue were purchased from a local market in the city of La Paz that were cultivated from the region of Sorata, Bolivia on three different months of the year (from April to August). The roots were washed, peeled under distilled water with ascorbic acid for 1 min to avoid oxidation. The material was cut into small pieces and minced in an Oster® blender (Model: 4172-051, Mexico) to obtain a yacón paste. Ascorbic acid (3 g/l disintegrated material) was added as an antioxidant while the root was minced. The yacón paste was stored at -20°C in many polypropylene containers of 100 mL between 3 and 7 days. To perform the experiments the yacón sample was thawed at room temperature for at least two hours.

Drying methodology
Samples of 100 g of yacón paste were weighed in a Petri dish (diameter = 14 cm, height = 2 cm) and spread. The average thickness of the sample inside the Petri dish was 3 mm. The sample was put into a convective drying tunnel oven   During each drying procedure, the weight of the sample and sample holder was recorded every minute until the end of the drying process. The end of the drying was established when the sample reached a constant weight. After completed drying, the samples were kept at room temperature completely sealed in polypropylene containers.
The drying rate and the extent of drying were followed by measuring the free moisture representing the amount of moisture present in the void spaces of the sample [12] and is represented by the eq. (1): Where m aq in the sample is the amount of water remaining after drying at a certain time, and m S represents the total solids in the sample that can be found using the dry matter of the undried yacón.     The water activity was measured using a water activity meter (Aqua Lab series 3) with a cooled mirror condensation detector. About one gram of each dried sample was put in a cup (d = 4 cm, h = 1 cm) in a uniform way and applied into the sample drawer of the water activity meter around 4 to 5 min per sample.
The color (CIE Lab color space) of the dried material was measured using a colorimeter (Chromameter CR-400, Konica Minolta) over the homogeneous surface of one gram of dried yacón sample without any treatment. It measures the parameters L*, a* and b* to describe the color. Parameter (L*) expresses the lightness of the sample and changes from dark (0-50) to light (51-100). Parameters

Reconstitution of the dried samples into a paste
The dried samples were reconstituted with pure water at a volume of 40 mL to the same dry matter (10.85%, 14.43%, and 11.94%) as the raw yacón paste from which they originated. After mixing using a magnetic stirrer, the samples were allowed to equilibrate for approximately one hour at room temperature before any measurements were performed.

Determination of water-insoluble solids and soluble solids of the pastes
Two grams of yacón paste was suspended in 10 mL of distilled water to determine the water-insoluble solids (WIS) of the original and the reconstituted paste. The mix was centrifuged at 3000 x g for 20 min at 20°C (Allegra X-1512, Beckman Coulter Inc. USA). The supernatant was filtered (paper filter 1F, Munktell Filter AB, Sweden) to recollect any residue in the suspension. The residue was washed out of any sugar repeatedly using distilled water until the washing liquid had a refractive index of about zero. The residue was dried in an oven at 105°C for 16 h and then weighed. The results are expressed as g WIS/100 g dry matter. The total watersoluble solids (WSS) were determined by drying all the supernatants collected from the water-insoluble solids measurements in an oven at 105°C for 16 h and then weighed. The results are expressed as g WSS/100 g dry matter and both the determination of WIS and WSS were performed in duplicate.

Particle size distribution of the yacón paste
The particle size distribution (PSD) of the solids of the different yacón pastes (refractive index of the suspension = 1.339) was measured using a laser diffraction analyzer (Malvern Mastersizer Hydro 2000 SM) in the 0.1-1000 μm interval and performed in duplicate. The most common descriptions of the particle size distribution are given as the surfaceweighted mean (d 32 ) and the volume-weighted mean (d 43 ). The parameters d 32 and d 43 are calculated using the following equations: where i is the index of population and d is the particle diameter of population i.

Rheological properties of the yacón paste
A controlled-stress rheometer (Malvern Kinexus Pro) equipped with a four blade vane geometry (d = 21 mm, height = 45 mm) giving a gap of 3 mm was used to perform the sinusoidal oscillatory tests. The purpose of using the vane geometry is to eliminate the slip phenomenon. The linear viscoelastic region, defined as the initial linear part (LVR) when applying a stress sweep test from 0.02 to 100 Pa at 1 Hz at 20°C was determined.
The measurements were performed in duplicate.

Determination of inulin-type fructans content in the yacón paste
The content of inulin-type fructans in the yacón paste was determined by applying an enzymatic method described by Steegmans et al. [13]. The total content of inulin-type fructans is expressed as g inulin-type fructans/100 g dry matter. The measurements were performed in duplicate.

Statistical analysis
The results were statistically treated using one-way analysis of variance (ANOVA, p < 0.05) using one of the three design parameters (yacón sample, drying temperature and air velocity). The correlations between properties were determined by using the Pearson correlation coefficient. Principal Component Analysis (PCA) was performed having two principal components showing loading plots and score plots. Minitab® 14.1.0.0 was used for statistical analysis, graphics and data processing. The precision of measurements is estimated from the variation between replicates.

The drying procedure of yacón
The average drying curves of the samples are shown in Fig. 2.The average standard deviation of each point in the curve varied from 0.2 to 0.8. It can be noted that the higher the temperature, the steeper the drying curves, which is in accordance with the results of drying carrots as given by Prabhanjan et al. [14] and the results of drying tomato slices as given by Coşkun et al. [15]. The time necessary to dry the sample decreased when the drying temperature increased (see Fig. 2). This is because higher temperatures provides larger heat flux, higher water vapor carrying capacity and a larger water vapor activity gradient. The increase of air velocity in the samples at the same temperature (60°C) also enhances the rate of drying, because air is responsible for the transfer of the heat as well of the evaporating water from the sample during the drying.
Before the drying, the moisture content of the different yacón was around 88%. The moisture content was calculated using the dry matter of the yacón samples. During the drying process the critical moisture concentration was reached after the removal of the majority of water (free moisture ≈ 0). During this latter part of the drying, the removal of hygroscopic moisture begins, but the quantity of the water remaining is usually low. The first section of the drying is faster than after reaching the critical moisture concentration [9]. The moisture content after the drying of yacón samples are between 13% and 4% depending of the drying temperature and air velocity used. By analyzing the drying curves, we can obtain the drying time and the drying rate. The drying rate represents the amount of free moisture per unit of time and is obtained from the first steep slope of the curves given in Fig. 2. The drying time is read off when reaching the critical moisture concentration. Table 6 Least-square means and significance of influence (F and pvalues) of drying temperature using 2 m/s on the dry matter, the water activity (a w ) and the color (L*, a* and b*) of the dried samples of yacón (one-way ANOVA). The R 2 values and the relative standard error between replicates are also given (n = 2)  The effects of the drying parameters, such as drying temperature and air velocity, on the drying time and the drying rate can be seen in Tables 2 and 3 using one-way ANOVA.
From the results presented, the drying time is significantly influenced by both the drying temperature and the air velocity. Similar observations were found in studies in which both the air velocity and temperature during the drying had a significant influence on the drying time of garlic slices [16] and bananas [9]. For instance, the drying times of bananas were about 520 and 320 min at 50°C and 70°C, respectively, using an air velocity of 3.3 m/s [9]. Comparing these results with the drying time of yacón at 50°C and 60°C using 2 m/s, the drying time of yacón is quicker than the drying time of banana when considering that the bananas were dried using a higher air velocity. Prabhanjan et al. [14] obtained a drying time of 390 min at 45°C and 90 min at 60°C during convective air drying of carrots at an air velocity of 1.7 m/s and these drying times were significantly lower in comparison with those of yacón achieved in this investigation especially at the higher drying temperatures.
The drying temperature was the only variable that significantly increased the drying rate. The drying rate of the yacon samples were (0.028 min −1 at 50°C and 0.036 min −1 at 60°C using an air velocity of 2 m/s) where the drying rate of bananas [9] was lower (0.001 min −1 at 50°C and 0.003 min −1 at 70°C using an air velocity of 3.3 m/s). This similar trend was also observed in Mohan [17] and Darıcı [18].
The air velocity helps to reduce the drying time, but its effect is less significant than the temperature. Krokida et al. [19] obtained similar results on the influence of air velocity when drying different types of vegetables.

Characterization of the dried samples
Dry matter, water activity and color (L*, a* and b*) was performed in yacón samples before drying (Table 4) and from the dried yacón obtained at different drying conditions (Tables 5, 6 and 7).
The initial dry matter of yacón before drying varies between 10.8 and 14.4 g/100 g sample. In Table 5, the dry matter  of dried material is about 92 g/100 g for the different samples, which tells us that the dried sample preserves about 8% of internal water after the drying procedure. The water activity, a w, is also low enough for good preservation of the dried samples. The type of yacón significantly influences the water activity, in where yacón 1 had the lowest value. With regard to the color in the different samples of yacón before and after the drying there is an increment in all the parameters (L*, a* and b*) after drying. The increase is higher with regard to the values of a* and b* which is observed in a darker coloration in the dried samples (Fig. 3). In Table 6, the dry matter of the yacón dried samples increases with temperature, reaching the highest value of 93 g/ 100 g sample at 60°C and this effect is significant. Similar effects of the drying temperature on the dry matter have also been seen for the drying of fruits like the Tunisian dates by Borchani et al. [20]. The drying temperature significantly influences the water activity giving the lowest value at the highest temperature. The effect of the temperature on the water activity was similar to that of powders of different date varieties [20].
The color of the dried samples is a visual representation of the effect of the different drying conditions. The drying temperature does not significantly influence lightness (L*) [21], but the yellowness (b*) and redness (a*) is enhanced in the dried samples with drying temperature. The drying of savory leaves by Nikjooy and Hashemi [22] showed there is an effect of rising the temperature on the color of the dry material particularly at the highest temperatures similar to the results obtained here for yacon. After the drying, the samples acquire a strong orange color (high a* and b* values). This change of color might be produced by oxidation, Maillard, and caramelization reactions [23] resulting in the formation of colored substances induced by the high temperatures that are applied to a food product for a longer period.
In Table 7, the dry matter significantly increased by the air velocity, whereas the air velocity did not significantly influence the water activity.
Although the air velocity does not seem to influence the majority of the color parameters significantly except for (b*), there is still a reduction of the drying time on increasing air velocity, thereby lowering the probability of reactions taking  Fig. 4 Behavior of the redness (a*) of the dried yacón as a function of the drying temperature and air speed place that will change the properties of the color of the sample. This effect of the drying conditions (temperature and air velocity) can be observed in Fig. 4 by analyzing the parameter (a*).

Characterization of the reconstituted yacón
The three types of fresh yacón used for the drying procedures were characterized by evaluation of the chemical parameters (WIS, WSS, and FOS), structural (particle size d 32 and d 43 ) and rheological (elastic modulus) parameters (Table 8).
In Table 8 the physicochemical properties of the yacon before drying is shown. Yacón 1 represents the least amount of water-insoluble solids but has the highest content of fructooligosaccharides, whereas yacón 2 has the largest water insoluble content and the highest elastic module of all the samples. In the case of yacón 1, which has the least amount of water-insoluble solids, the value of the elastic module is the lowest. All the measured properties of the three original yacons were significantly different.
The results of the characterization of the reconstituted yacón prepared from the dried samples obtained from the drying were analyzed in the same way as the original yacón pastes, i.e. chemically, structurally and rheologically. The results were further analyzed using one-way ANOVA to allow us to describe the properties as a function of the design parameters: yacón type, drying temperature and drying air velocity (see Tables 9, 10 and 11).
It is interesting to compare the properties of the dried and reconstituted yacon (Table 9) with the fresh yacon (Table 8). It can be observed that by drying yacon there is a substantial loss in WIS, elastic modulus, and FOS. This is especially pronounced for yacon 2, which after drying has the lowest WIS and elastic modulus among the three tested yacons, whereas the same yacon 2 is the one with the highest WIS and elastic modulus when being fresh. The smallest particles (d 32 ) do not change much on drying, whereas the larger ones (d 43 ) increase somewhat. The reason for this behavior on drying can be due to cellular breakdown and further disintegration of the cellular wall causing mainly a loss in WIS and consistency of the paste.
In Table 10, it can be observed that the amount of waterinsoluble solids increased significantly with the drying temperature but decreased again at the highest temperature of 60°C. Huang et al. [24] found a similar behavior related to the insoluble solids working with the drying of citrus byproducts with temperatures of 50°C, 60°C and 70°C. This different behavior at the highest temperature of 60°C might be produced by a loosening of pectin and cell wall structures that can occur at this high temperature thereby increasing their solubility [24].  Both parameters of the particle size distribution (d 32 and d 43 ) are not significantly influenced by the air velocity or by the drying temperature.
The drying temperature has not a significant influence on the rheological behavior. However, it can be observed that amount of water-insoluble solids and elastic modulus change similarly, and the drying temperature significantly influences the WIS. Thus, the temperature has an indirect influence on the loss of texture.
The influence of the air velocity at 60°C on the physicochemical properties of the reconstituted samples is shown in Table 11. Although the air velocity has no significant influence on the physicochemical properties, there is a tendency that an increase in the air velocity reduces the loss of waterinsoluble solids and increases the elastic modulus (this is almost significant). Figure 5 shows the behavior of the elastic modulus at different drying conditions, where yacón samples at 60°C and 2 m/s had the lowest value of elastic modulus, but by increasing the air velocity the elastic modulus started to increase again up to the highest level of all the dried samples.

Relationship between properties
We can analyze the correlation between the physicochemical properties of the dried and reconstituted yacón statistically by using Principal Component Analysis (PCA), and the results are presented in a loading plot and a score plot (Figs. 6 and 7).
There is a positive correlation between water-insoluble solids and elastic modulus using Pearson coefficient correlation (r = 0.940, p = 0.005). Another correlation between water activity and the elastic modulus (r = 0.972, p = 0.001) observed using Pearson coefficient correlation, suggests that with a better network of the yacón suspension the better the water is held in the network.
In the loading plot (Fig. 6), the principal component 1 (PC1) explains 60% of the variation, and the principal component 2 (PC2) explains 22% of the variation, respectively. There are positive correlations between many physicochemical properties, especially between water insoluble solids (WIS) and the elastic modulus. The parameter d 43 presents a positive correlation with WIS and elastic modulus, and for the latter, the values of the Pearson coefficient correlation are r =  0.543, p = 0.000, whereas those between d 43 and WIS are r = 0.703, p = 0.000. This latter relationship suggests that when WIS and the elastic modulus of the reconstituted paste are higher, the insoluble part is more aggregated (a higher d 43 ).
Analyzing the score plot of the principal component analysis (Fig. 7) and taking into consideration the loading plot, we observe tendencies between the different drying conditions. Most of the samples dried at 55°C, 2 m/s and at 60°C, 4 m/ s are similar and tend to present high values of the elastic modulus and water-insoluble solids. The samples dried at 60°C, 2 m/s, which have the lowest value of waterinsoluble solids and elastic modulus are dissimilar with the samples dried at 55°C, 2 m/s and at 60°C, 4 m/s, and those scores are mostly concentrated in the upper left corner opposite to the high elastic modulus and WIS.

Conclusions
Yacón roots have great potential for application in the food industry for its content of fructo oligosaccharides but the high content of water in yacón roots makes it difficult to preserve the root for a longer period of time. Drying is a suitable way to preserve yacón roots as it easily allows for a reduction of the water so a range of water activity of 0.3 to 0.5 is achieved.
According to the results, it is best to dry yacón when aiming for a minimal alteration of the overall physicochemical properties either by using relatively high temperatures of 55°C and 2 m/s or the highest temperature of 60°C but then with a higher air velocity of 4 m/s. Evidently, the higher the drying temperature the faster the drying of the yacón and thereby avoiding alterations of the overall physicochemical properties. This does not hold, however, for a drying temperature of 60°C, where detrimental effects in the properties of yacón occur. Increasing the air velocity from 2 to 4 m/s helps to decrease the detrimental effects in the properties of yacón when a temperature of 60°C is used.
Besides, by analyzing both the PCA and the Pearson coefficient correlation, it can be observed that many properties in the yacón, i.e. water insoluble solids and elastic modulus, correlate well with each other.
In conclusion, even for the drying conditions that show properties of the dried yacón more similar to the fresh sample, there is always a loss in some of the physicochemical properties of yacón, after drying.