Abstract
Pyroelectric materials have recently gained much interest due to their low cost and environment-friendly strategy for energy harvesting. However, the effectiveness of such methods is restricted by the typical properties of lead-free pyroelectric materials. Various methods are discussed to enhance the pyroelectric properties, including doping, composites, porous structure and functionally graded materials. Different techniques for measuring the pyroelectric coefficient and figures of merits responsible for effective energy harvesting are also systematically introduced. Further, numerous approaches for harvesting solar thermal and low-grade energy (temperature of system <230 °C) are considered. Apart from the conventional methods, pyroelectric material embedded with phase change materials and power-enhancing circuits to boost the energy harvested are also discussed.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Aggarwal M, Batra A, Guggilla P, Edwards M, Penn B, Currie Jr J (2010) Pyroelectric materials for uncooled infrared detectors: processing, properties, and applications
Anton E-M, Jo W, Damjanovic D, Rödel J (2011) Determination of depolarization temperature of (Bi1/2Na1/2) TiO3-based lead-free piezoceramics. J Appl Phys 110(9):094108
Azad P, Vaish R (2019) Solar energy harvesting using pyroelectric effect associated with piezoelectric buzzer. Physica status solidi (a) 216(20):1900440
Balakt AM, Shaw CP, Zhang Q (2016) The effects of Ba2+ content on depolarization temperature and pyroelectric properties of lead-free 0.94Na0.5Bi0.5TiO3–0.06Ba1+xTiO3 ceramics. J Mater Sci: Mater Electron 27(12):12947–12954
Balakt AM, Shaw C, Zhang Q (2017a) Large pyroelectric properties at reduced depolarization temperature in A-site nonstoichiometry composition of lead-free 0.94NaxBiyTiO3–0.06BazTiO3 ceramics. J Mater Sci 52(12):7382–7393
Balakt AM, Shaw CP, Zhang Q (2017b) Giant pyroelectric properties in La and Ta co-doped lead-free 0.94Na0.5Bi0.5TiO3–0.06BaTiO3 ceramics. J Alloys Comp 709:82–91
Balakt AM, Shaw CP, Zhang Q (2017c) Enhancement of pyroelectric properties of lead-free 0.94 Na0.5Bi0.5TiO3–0.06BaTiO3 ceramics by La doping. J Eur Ceramic Soc 37(4):1459–1466
Balakt AM, Shaw C, Zhang Q (2017d) Large pyroelectric properties at reduced depolarization temperature in A-site nonstoichiometry composition of lead-free 0.94NaxBiyTiO3–0.06BazTiO3 ceramics. J Mater Sci 52(12):7382–7393
Balakt AM, Shaw CP, Zhang Q (2017e) Enhancement of pyroelectric properties of lead-free 0.94Na0.5Bi0.5TiO3–0.06BaTiO3 ceramics by La doping. J Eur Ceramic Soc 37(4):1459–1466
Balakt AM, Shaw CP, Zhang Q (2017f) The decrease of depolarization temperature and the improvement of pyroelectric properties by doping Ta in lead-free 0.94Na0.5Bi0.5TiO3–0.06BaTiO3 ceramics. Ceramics Int 43(4):3726–3733
Batra A, Aggarwal M, Edwards ME, Bhalla A (2008) Present status of polymer: ceramic composites for pyroelectric infrared detectors. Ferroelectrics 366(1):84–121
Battista L, Mecozzi L, Coppola S, Vespini V, Grilli S, Ferraro P (2014) Graphene and carbon black nano-composite polymer absorbers for a pyro-electric solar energy harvesting device based on LiNbO3 crystals. Appl Energy 136:357–362
Bauer S, Lang SB (1996) Pyroelectric polymer electrets. IEEE Trans Dielectr Electr Insul 3(5):647–676
Bauer S, Ploss B (1990) A heat wave method for the measurement of thermal and pyroelectric properties of pyroelectric films. Ferroelectrics 106(1):393–398
Benke A, Mehner E, Rosenkranz M, Dmitrieva E, Leisegang T, Stöcker H, Pompe W, Meyer DC (2015) Pyroelectrically driven ·OH generation by barium titanate and palladium nanoparticles. J Phys Chem C 119(32):18278–18286
Bowen CR, Taylor J, LeBoulbar E, Zabek D, Chauhan A, Vaish R (2014) Pyroelectric materials and devices for energy harvesting applications. Energy Environ Sci 7(12):3836–3856
Byer RL, Roundy C (1972) Pyroelectric coefficient direct measurement technique and application to a Nsec response time detector. Ferroelectrics 3(1):333–338
Chynoweth A (1956) Dynamic method for measuring the pyroelectric effect with special reference to barium titanate. J Appl Phys 27(1):78–84
Daglish M (1998) A dynamic method for determining the pyroelectric response of thin films. Integr Ferroelectr 22(1–4):473–488
Dias C, Das Gupta D (1994) Piezo-and pyroelectricity in ferroelectric ceramic-polymer composites. in Key engineering materials. Trans Tech Publ J 92:217–248
Dubey A, Basu B, Balani K, Guo R, Bhalla A (2011) Dielectric and pyroelectric properties of HAp-BaTiO3 composites. Ferroelectrics 423(1):63–76
Ehre D, Cohen H (2013) Contact-free pyroelectric measurements using x-ray photoelectron spectroscopy. Appl Phys Lett 103(5):052901
Garn LE, Sharp EJ (1982) Use of low‐frequency sinusoidal temperature waves to separate pyroelectric currents from nonpyroelectric currents. Part I. Theory. J Appl Phys 53(12):8974–8979
Glass A (1969) Investigation of the electrical properties of Sr1−xBaxNb2O6 with special reference to pyroelectric detection. J Appl Phys 40(12):4699–4713
Groten J, Zirkl M, Jakopic G, Leitner A, Stadlober B (2010) Pyroelectric scanning probe microscopy: a method for local measurement of the pyroelectric effect in ferroelectric thin films. Phys Rev B 82(5):054112
Gutmann E, Benke A, Gerth K, Böttcher H, Mehner E, Klein C, Krause-Buchholz U, Bergmann U, Pompe W, Meyer DC (2012) Pyroelectrocatalytic disinfection using the pyroelectric effect of nano-and microcrystalline LiNbO3 and LiTaO3 particles. J Phys Chem C 116(9):5383–5393
Guyomar D, Sebald G, Lefeuvre E, Khodayari A (2009) Toward heat energy harvesting using pyroelectric material. J Intell Mater Syst Struct 20(3):265–271
Hartley N, Squire P, Putley E (1972) A new method of measuring pyroelectric coefficients. J Phys E: Sci Instrum 5(8):787
He H, Lu X, Hanc E, Chen C, Zhang H, Lu L (2020) Advances in lead-free pyroelectric materials: a comprehensive review. J Mater Chem C 8(5):1494–1516
Ianculescu A, Pintilie I, Vasilescu C, Botea M, Iuga A, Melinescu A, Drăgan N, Pintilie L (2016) Intrinsic pyroelectric properties of thick, coarse grained Ba1−xSrxTiO3 ceramics. Ceram Int 42(8):10338–10348
Jachalke S, Mehner E, Stöcker H, Hanzig J, Sonntag M, Weigel T, Leisegang T, Meyer D (2017) How to measure the pyroelectric coefficient? Appl Phys Rev 4(2):021303
Kishore RA, Priya S (2018) A review on low-grade thermal energy harvesting: materials, methods and devices. Materials 11(8):1433
Kong LB, Li T, Hng HH, Boey F, Zhang T, Li S (2014) Waste energy harvesting: mechanical and thermal energies, vol 24. Springer Science & Business Media
Kumar M, Patel M, Nguyen TT, Kim J, Yi J (2018a) High-performing ultrafast transparent photodetector governed by the pyro–phototronic effect. Nanoscale 10(15):6928–6935
Kumar A, Vaish R, Kumar S, Singh V, Vaish M, Singh Chauhan V, Srikanth KS (2018b) Lead‐free pyroelectric materials for thermal energy harvesting: a comparative study. Energy Technol 6(5):943–949
Kutnjak Z, Rožič B, Pirc R (1999) Electrocaloric effect: theory, measurements, and applications. Wiley encyclopedia of electrical and electronics engineering, pp 1–19
Lam K-H, Wang X, Chan HL-W (2005) Piezoelectric and pyroelectric properties of (Bi0.5Na0.5)0.94 Ba0.06TiO3/P (VDF-TrFE) 0–3 composites. Comp Part A: Appl Sci Manuf 36(11):1595–1599
Lang SB (2005) Pyroelectricity: from ancient curiosity to modern imaging tool. Phys Today 58(8):31
Lang SB, Das-Gupta DK (2001) Pyroelectricity: Fundamentals and applications. Handbook of advanced electronic and photonic materials and devices. Elsevier, pp 1–55
Lang SB, Muensit S (2006) Review of some lesser-known applications of piezoelectric and pyroelectric polymers. Appl Phys A 85(2):125–134
Lang SB, Steckel F (1965) Method for the measurement of the pyroelectric coefficient, dc dielectric constant, and volume resistivity of a polar material. Rev Sci Instrum 36(7):929–932
Lee FY, Navid A, Pilon L (2012) Pyroelectric waste heat energy harvesting using heat conduction. Appl Therm Eng 37:30–37
Leng Q, Chen L, Guo H, Liu J, Liu G, Hu C, Xi Y (2014) Harvesting heat energy from hot/cold water with a pyroelectric generator. J Mater Chem A 2(30):11940–11947
Lheritier P, Torelló A, Usui T, Nouchokgwe Y, Aravindhan A, Li J, Prah U, Kovacova V, Bouton O, Hirose S (2022) Large harvested energy with non-linear pyroelectric modules. Nature 609(7928):718–721
Li H, Li W, Yang Y, Tai H, Du X, Gao R, Li S (2018) Pyroelectric performances of 1–3 ferroelectric composites based on barium titanate nanowires/polyvinylidene fluoride. Ceram Int 44(16):19254–19261
Li M, Zhang H, Cook SN, Li L, Kilner JA, Reaney IM, Sinclair DC (2015) Dramatic influence of A-site nonstoichiometry on the electrical conductivity and conduction mechanisms in the perovskite oxide Na0.5Bi0.5TiO3. Chem Mater 27(2):629–634
Liu S, Long D (1978) Pyroelectric detectors and materials. Proc IEEE 66(1):14–26
Lovinger AJ (1983) Ferroelectric polymers. Science 220(4602):1115–1121
Lubomirsky I, Stafsudd O (2012) Invited review article: practical guide for pyroelectric measurements. Rev Sci Instrum 82(5):121101
Luo W, Yu Y, Shuai Y, Pan X, Wu Q, Wu C, Zhang W (2016) Enhanced pyroelectric properties of lead free KNN/P (VDF-TrFE) composite film by optimizing KNN sintering temperature. J Mater Sci: Mater Electron 27(3):2288–2292
Mahdi R, Majid WA (2016) Piezoelectric and pyroelectric properties of BNT-base ternary lead-free ceramic–polymer nanocomposites under different poling conditions. RSC Adv 6(84):81296–81309
Martınez F, Hinojosa J, Doménech G (2013) Dielectric constant tunability at microwave frequencies and pyroelectric behavior. IEEE Trans Ultrason Ferroelectr Freq Control 60:1595–1602
Matocha K, Chow T, Gutmann R (2002) Positive flatband voltage shift in MOS capacitors on n-type GaN. IEEE Electron Device Lett 23(2):79–81
Navid A, Pilon L (2011) Pyroelectric energy harvesting using Olsen cycles in purified and porous poly (vinylidene fluoride-trifluoroethylene) [P (VDF-TrFE)] thin films. Smart Mater Struct 20(2):025012
Nguyen H, Navid A, Pilon L (2010) Pyroelectric energy converter using co-polymer P (VDF-TrFE) and Olsen cycle for waste heat energy harvesting. Appl Therm Eng 30(14–15):2127–2137
Olszowy M, Pawlaczyk C, Markiewicz E, Kułek J (2005) Dielectric and pyroelectric properties of BaTiO3–PVC composites. Physica Status Solidi (A) 202(9):1848–1853
Park T, Na J, Kim B, Kim Y, Shin H, Kim E (2015) Photothermally activated pyroelectric polymer films for harvesting of solar heat with a hybrid energy cell structure. ACS Nano 9(12):11830–11839
Parravicini J, Safioui J, Degiorgio V, Minzioni P, Chauvet M (2011) All-optical technique to measure the pyroelectric coefficient in electro-optic crystals. J Appl Phys 109(3):033106
Patel S, Kumar M (2020) Influence of grain size on the electrocaloric and pyroelectric properties in non-reducible BaTiO3 ceramics. AIP Adv 10(8):085302
Patel S, Lalitha KV, Saurabh N (2021) Enhanced pyroelectric performance of lead-free Zn-doped Na1/2Bi1/2TiO3-BaTiO3 ceramics. Materials 15(1):87
Patel S, Chauhan A, Vaish R (2016) Large pyroelectric figure of merits for Sr-modified Ba0.85Ca0.15Zr0.1Ti0.9O3 ceramics. Solid State Sci 52:10–18
Popescu S, Petris A, Vlad V (2013) Interferometric measurement of the pyroelectric coefficient in lithium niobate. J Appl Phys 113(4):043101
Porter S (1981) A brief guide to pyroelectric detectors. Ferroelectrics 33(1):193–206
Qian W, Wu Z, Jia Y, Hong Y, Xu X, You H, Zheng Y, Xia Y (2017) Thermo-electrochemical coupling for room temperature thermocatalysis in pyroelectric ZnO nanorods. Electrochem Commun 81:124–127
Roscow J, Zhang Y, Taylor J, Bowen C (2015) Porous ferroelectrics for energy harvesting applications. Eur Phys J Spec Top 224(14):2949–2966
Sakata K, Masuda Y (1974) Ferroelectric and antiferroelectric properties of (Na0.5Bi0.5)TiO3–SrTiO3 solid solution ceramics. Ferroelectrics 7(1):347–349
Satish B, Sridevi K, Vijaya M (2002) Study of piezoelectric and dielectric properties of ferroelectric PZT-polymer composites prepared by hot-press technique. J Phys D Appl Phys 35(16):2048
Saurabh N, Patel S (2021) Nonstoichiometric effect on electrocaloric, pyroelectric and energy storage properties of 0.94NaxBiyTiO3–0.06BaTiO3 bulk ceramics. J Mater Sci: Matern Electron 32(22):26871–26893
Saurabh N, Kiran R, Patel S (2022) Solar energy harvesting using lead-free pyroelectric bulk ceramics: a simulation study. J Sci: Adv Mater Dev 100527
Sawyer CB, Tower C (1930) Rochelle salt as a dielectric. Phys Rev 35(3):269
Schein LB, Cressman PJ, Cross LE (1978) Electrostatic measurements of unusually large secondary pyroelectricity in partially clamped LiNbO3. Ferroelectrics 22(1):937–943
Sebald G, Lefeuvre E, Guyomar D (2008) Pyroelectric energy conversion: optimization principles. IEEE Trans Ultrason Ferroelectr Freq Control 55(3):538–551
Sharma M, Chauhan A, Vaish R, Chauhan VS (2015) Pyroelectric materials for solar energy harvesting: a comparative study. Smart Mater Struct 24(10):105013
Sharma M, Singh V, Singh S, Azad P, Ilahi B, Madhar NA (2018) Porous Ba0.85Ca0.15Zr0.1Ti0.9O3 ceramics for pyroelectric applications. J Electron Mater 47(8):4882–4891
Sharp EJ, Garn LE (1982) Use of low‐frequency sinusoidal temperature waves to separate pyroelectric currents from nonpyroelectric currents. Part II. experiment. J Appl Phys 53(12):8980–8987
Shaw CP, Whatmore RW, Alcock JR (2007) Porous, functionally gradient pyroelectric materials. J Am Ceram Soc 90(1):137–142
Shen M, Qin Y, Zhang Y, Marwat MA, Zhang C, Wang W, Li M, Zhang H, Zhang G, Jiang S (2019) Enhanced pyroelectric properties of lead-free BNT-BA-KNN ceramics for thermal energy harvesting. J Am Ceram Soc 102(7):3990–3999
Sratta Y, Chandarak S, Unruan M, Kantha P, Marungsri B, Yimnirun R, Pojprapai S (2013) Effect of temperature on ferroelectric properties of Bismuth Ferrite-Barium Titanate. Integr Ferroelectr 148(1):67–72
Srikanth K, Patel S, Vaish R (2018) Pyroelectric performance of BaTi1-xSnxO3 ceramics. Int J Appl Ceram Technol 15(2):546–553
Stuart MAC, Huck WT, Genzer J, Müller M, Ober C, Stamm M, Sukhorukov GB, Szleifer I, Tsukruk VV, Urban M (2010) Emerging applications of stimuli-responsive polymer materials. Nat Mater 9(2):101–113
Sussner H, Horne D, Yoon D (1978) A new method for determining the pyroelectric coefficient of thin polymer films using dielectric heating. Appl Phys Lett 32(3):137–139
Tok AI, Boey FY, Khor K (1999) Tape casting of high dielectric ceramic composite substrates for microelectronics application. J Mater Process Technol 89:508–512
Wang Y, Zhong W, Zhang P (1993) Pyroelectric properties of ferroelectric-polymer composite. J Appl Phys 74(1):521–524
Wang Z, Yu R, Pan C, Li Z, Yang J, Yi F, Wang ZL (2015) Light-induced pyroelectric effect as an effective approach for ultrafast ultraviolet nanosensing. Nat Commun 6(1):1–7
Wang X-Q, Tan CF, Chan KH, Xu K, Hong M, Kim S-W, Ho GW (2017a) Nanophotonic-engineered photothermal harnessing for waste heat management and pyroelectric generation. ACS Nano 11(10):10568–10574
Wang X, Dai Y, Liu R, He X, Li S, Wang ZL (2017b) Light-triggered pyroelectric nanogenerator based on a pn-junction for self-powered near-infrared photosensing. ACS Nano 11(8):8339–8345
Whatmore R (1986) Pyroelectric devices and materials. Rep Prog Phys 49(12):1335
Whatmore R (1991) Pyroelectric ceramics and devices for thermal infra-red detection and imaging. Ferroelectrics 118(1):241–259
Xie M, Zabek D, Bowen C, Abdelmageed M, Arafa M (2016) Wind-driven pyroelectric energy harvesting device. Smart Mater Struct 25(12):125023
Xu X, Xiao L, Jia Y, Wu Z, Wang F, Wang Y, Haugen NO, Huang H (2018) Pyro-catalytic hydrogen evolution by Ba0.7Sr0.3TiO3 nanoparticles: harvesting cold–hot alternation energy near room-temperature. Energy Environ Sci 11(8):2198–2207
Xue H, Yang Q, Wang D, Luo W, Wang W, Lin M, Liang D, Luo Q (2017) A wearable pyroelectric nanogenerator and self-powered breathing sensor. Nano Energy 38:147–154
Yan M, Xiao Z, Ye J, Yuan X, Li Z, Bowen C, Zhang Y, Zhang D (2021) Porous ferroelectric materials for energy technologies: current status and future perspectives. Energy Environ Sci 14:6158–6190
Yang Y, Jung JH, Yun BK, Zhang F, Pradel KC, Guo W, Wang ZL (2012) Flexible pyroelectric nanogenerators using a composite structure of lead-free KNbO3 nanowires. Adv Mater 24(39):5357–5362
You H, Ma X, Wu Z, Fei L, Chen X, Yang J, Liu Y, Jia Y, Li H, Wang F (2018) Piezoelectrically/pyroelectrically-driven vibration/cold-hot energy harvesting for mechano-/pyro-bi-catalytic dye decomposition of NaNbO3 nanofibers. Nano Energy 52:351–359
Yu C, Park J, Youn JR, Song YS (2022) Sustainable solar energy harvesting using phase change material (PCM) embedded pyroelectric system. Energy Convers Manag 253:115145
Zhang M, Hu Q, Ma K, Ding Y, Li C (2020) Pyroelectric effect in CdS nanorods decorated with a molecular Co-catalyst for hydrogen evolution. Nano Energy 73:104810
Zhang D, Wu H, Bowen CR, Yang Y (2021) Recent advances in pyroelectric materials and applications. Small 17(51):2103960
Zhang Y, Xie M, Roscow J, Bao Y, Zhou K, Zhang D, Bowen CR (2017) Enhanced pyroelectric and piezoelectric properties of PZT with aligned porosity for energy harvesting applications. J Mater Chem A 5(14):6569–6580
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2024 The Author(s), under exclusive license to Springer Nature Singapore Pte Ltd.
About this chapter
Cite this chapter
Saurabh, N., Patel, S. (2024). Methods to Enhance the Pyroelectric Properties and Energy Harvesting. In: Goyal, R., Patel, S., Sharma, A. (eds) Renewable Energy: Accelerating the Energy Transition. Energy Systems in Electrical Engineering. Springer, Singapore. https://doi.org/10.1007/978-981-99-6116-0_15
Download citation
DOI: https://doi.org/10.1007/978-981-99-6116-0_15
Published:
Publisher Name: Springer, Singapore
Print ISBN: 978-981-99-6115-3
Online ISBN: 978-981-99-6116-0
eBook Packages: EnergyEnergy (R0)