In Situ Destructive Sampling

When designing experiments, environmental scientists face the challenge of how to accurately represent nature. The idea of sampling patterns and strategies truly reflecting research variables is intrinsic to scientific pursuits. This is particularly true in environmental science due to the complex heterogeneity present in nature. It is vitally important in most studies for researchers to account for natural variations in soil, air, water, and vegetation that can change in space and time. Many strategies focus on the use of strategically placed transects or plot-based sampling campaigns designed to include as many aspects of a particular variable as possible within a study area. Determining how many samples must be taken, whether they are of soil, plant matter, water, etc., depends entirely on the balance of time, effort, and cost while in the field. As a rule of thumb, the more samples that can be gathered correctly, the more trustworthy eventual results will be. Unfortunately, environmental sampling can be time-consuming and expensive depending on its location or the procedures for its procurement. This is one of the reasons why the use of satellite-based remote sensing, computer modeling, and proximal sensing has gained popularity within the scientific community in recent decades. However, the heterogeneity and scale of the environment again make large spatial-scale research difficult and often require in situ validation campaigns to ensure data quality. This is one of the main advantages of the use of the CRNS, due to the significant spatial and temporal variations soil moisture can exhibit.

ensure data quality. This is one of the main advantages of the use of the CRNS, due to the significant spatial and temporal variations soil moisture can exhibit.

Plant Sampling Pattern and Design
The calibration process for the CRNS technique has been extensively detailed and is a prime example of controlling for heterogeneity within agricultural environments [1][2][3][4][5][6]. The CRNS calibration function first proposed by Desilets et al. [1] is designed primarily around a sampling structure within the circular footprint of the instrument (circle of radius ~ 250 m). Specifically, 18 sampling sites are distributed on six transects located every 60° within the circle. Along each transect three sampling sites are located at 25, 75, and 200 m from the center point (usually where the CRNS is located; see

Sampling Instructions
Along with soil samples, plant samples are taken at each of the 18 sampling sites. The following is a step by step guide for proper in situ destructive sampling: Step One: Randomly select one to three individual plants (depending on crop size, large plants such as fully grown maize may be impractical to remove three individuals) spaced apart from each other, and pull them from the ground as to preserve as much root structure as possible.
Step Two: Shake any loose soil from the bottom of the plant so only the plant itself remains.
Step Three: Place the entire plant into a brown paper bag (or other containers) labeled appropriately (i.e., plants 1-3, point numbers 1-18; see Fig. 2.1); be careful to minimize folding or breaking of the plant cellular structure during removal and placement into the bag as to minimize any water loss.
Step Four: Fill back each hole left by the removed plants and repeat process at each of the 18 sampling locations collecting one to three plants at each site.

Biomass Water Equivalent
Fundamentally, the CRNS detects all environmental hydrogen within its footprint including hydrogen in soil moisture water molecules (see Fig. 2.2). As such, the primary component of crop biomass that introduces error to the CRNS signal is cellular water. The term biomass water equivalent (BWE, mm of H 2 O) is used in the CRNS calibration functions to describe the equivalent amount of water that would be required to introduce the same amount of water as a particular type of living crop biomass. It is defined as follows (Eq. 2.1) where SWB and SDB stand for standing wet and dry biomass, respectively, (kg/m 2 ) and f WE = 0.494 which is the stoichiometric ratio of H 2 O to organic carbon molecules in the plant (assuming this is mostly cellulose C 6 H 10 O 5 ) [4,5]. Note: the units in the following equation are mass per unit area which is equivalent to a depth of water. During destructive sampling between one and three plants are removed. As such, an average plant density must be known to calculate into kg/m 2 or mm H 2 O (i.e., by dividing by the density of water = 1000 kg/ m 3 and multiplying by 1000 to convert m to mm). The plant density can be estimated by laying down a quadrat (i.e., a square of dimensions 50×50 cm, 1×1 m, etc. made of PVC) and counting the number of plants inside the encompassed area.

Processing Instructions
After initial in situ collection, time becomes a highly relevant factor due to the water loss freshly harvested biomass samples experience immediately upon removal from the field. The following is a step by step guide on the proper weighing and ovendrying protocols for the determination of BWE: Step One: Weigh biomass samples while they are still full of water as soon as possible from the time of their removal from the soil. This should be done with the plants in a container placed on the scale after zeroing. This can be difficult with fully grown maize plants but can be done if the plant is folded or cut within the container until it fits and then promptly weighed.
Step Two: Dry the plants in a standard convection drying oven at 70 ° C for 120 h (can check mass at 96 h and 120 h to make sure it is not changing by more than 1% between time intervals; otherwise, continue for an additional 24 h).
Step Three: Remove dried plants and weigh them once more.

Conclusions
The calibration process for the CRNS technique involves in situ sampling of biomass designed to quantify the hydrogen in its cellular structure and the water within. Traditional destructive biomass sampling is employed in a radial sampling pattern controlling for spatial variability of soil, water, and vegetation characteristics. This section provides detailed descriptions of biomass sampling procedures and the The main limitation of this form of sampling is its timeconsuming nature and therefore is limited to a few fields at a time. This works well for stationary CRNS locations where the BWE must be calculated for one singular field but becomes difficult when mobile versions of the CRNS technique are employed in which the BWE must be determined for many fields (see Franz et al. (2015) and Avery et al. (2016) for more details on the mobile aspects of this technology [4,5]).
The opinions expressed in this chapter are those of the author(s) and do not necessarily reflect the views of the International Atomic Energy Agency (IAEA), its Board of Directors, or the countries they represent. Open Access This chapter is licensed under the terms of the Creative Commons Attribution 3.0 IGO license (https://creativecommons.org/licenses/by/3.0/igo/), which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the IAEA, provide a link to the Creative Commons license and indicate if changes were made.
Any dispute related to the use of the works of the IAEA that cannot be settled amicably shall be submitted to arbitration pursuant to the UNCITRAL rules. The use of the IAEA's name for any purpose other than for attribution, and the use of the IAEA's logo, shall be subject to a separate written license agreement between the IAEA and the user and is not authorized as part of this CC-IGO license. Note that the link provided above includes additional terms and conditions of the license.
The images or other third party material in this chapter are included in the chapter's Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the chapter's Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder.