Analytical Solution for the Electric Field Response Generated by a Nonconducting Ellipsoid (Prolate Spheroid) in a Conducting Fluid Subject to an External Electric Field

An analytical solution is presented for the electric field response generated by a nonconducting ellipsoid (prolate spheroid) in a homogeneous conducting fluid subject to an external primary electric field, including surface charge distribution. Such a solution might be useful for different purposes, including cell modeling subject to an external quasistatic electromagnetic stimulus. The solution utilizes the well-known analogy between the electrostatics of dielectrics and DC conduction. The solution obtained includes an expression for the volumetric fields and an expression for the induced surface charge density at the membrane.


Introduction
In this short study, we retrieve and discuss an analytical solution for the electric field response generated by a nonconducting ellipsoid (prolate spheroid) in a homogeneous conducting fluid subject to an external primary electric field. We assume that the primary field can have any angle of incidence with respect to the longer axis of the ellipsoid. We assume that the ellipsoid has a zero (a nonconducting cell membrane) conductivity.
In the main text, we will utilize the well-known analogy between the electrostatics of dielectrics and DC conduction [1][2][3]. This analogy means that the basic equations and the corresponding solutions become identical when the ratio(s) of dielectric constants will coincide with the ratio(s) of conductivities. Since the solution of the present problem for dielectric materials does exist [1], its conversion to the conducting case is rather straightforward, but it requires extra steps for computing the induced charge density at the interface.
Here we also note that such an analogy is not the only one: one might consider a relevant fluid dynamics analogy as well. For example, the solution for a potential flow of an ideal incompressible fluid around a sphere with radius R [4] yields the expression for the hydrodynamic potential in the following form (the flow direction is along the x-axis): An unknown coefficient B is found from the condition ∂φ v ∂r ¼ 0, which allows us to write the following expression for the potential: Simultaneously, the tangential velocity at the sphere surface is given by This solution is equivalent to the steady electric current solution for a nonconducting sphere in a conducting fluid. In particular, the electric field inside the sphere is given by (cf. [3]): where E ! 0 is the primary electric field. On the other hand, for a dielectric sphere with permittivity ε in a dielectric medium with permittivity ε, the corresponding solution for the field inside has the following form [1][2][3]: Two solutions (4) and (5) indeed coincide when

Materials and Methods
In Ref. [1], the problem is solved for the electric field of an ellipsoid with half axes a, b, c, with permittivity ε (i) in a dielectric medium with permittivity ε (e) when a primary or external field E ! 0 is applied. This solution will be repeated here; the final result implies that the permittivities should be replaced by conductivities.
We consider an ellipsoid in the form of a prolate spheroid (a > b ¼ c). The coordinate system (see Fig. 1) is chosen as follows: the z-axis is directed along a so that the angle between the z-axis and the vector E ! 0 is less than 90 degrees. The x-axis is located in a plane defined by the z-axis and vector E ! 0 . The y-axis is then chosen to construct the right-handed Cartesian system. In this coordinate system, the depolarization tensor [1] becomes diagonal with the following components: For the prolate spheroid, simplifications are made in the following form [1]: is the ellipsoid eccentricity.

Results for the Potential and the Electric Field
Accordingly, the electric potential everywhere in space and the electric field inside the ellipsoid have the following form [1] (the ratio of dielectric permittivities in the equations given below must be set to zero to obtain the result for the nonconducting ellipsoid in the conducting fluid): Here, ξ is the ellipsoidal coordinate that is a constant for all ellipsoids being confocal with the given one. For the prolate spheroid, one has ξ ¼ a = ffiffiffiffiffiffiffiffiffi a 2 Àb 2 p . Now, we express the electric field in the following form (ϑ is the elevation angle): After substitution of Eq. (10) into Eq. (9) and using Eq. (6), we obtain φ ðiÞ ¼ À It follows from Eqs. (8) and (11) that the electric field within the ellipsoid is not parallel to the external primary electric field.

Results for the Surface Charge Density
For the prolate spheroid, the ellipsoidal coordinates are reduced to the prolate spheroidal coordinates ξ, η, and ψ. They are converted to Cartesian coordinates using the following expressions [5]: where d is the spacing between two focal points of the ellipsoid, which is equal to 2 ffiffiffiffiffiffiffiffiffiffiffiffiffiffi ffi a 2 À b 2 p . In order to find the surface charge distribution, one needs to find the normal derivative of the electric potential at the surface. Since the outer normal derivative of the potential is equal to zero, only the inner derivative is needed. coaxial external field. Here, the opposite charges are concentrated close to the cylinder tips only.
Open Access This chapter is licensed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license and indicate if changes were made.
The images or other third party material in this chapter are included in the chapter's Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the chapter's Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder.