Skip to main content
SpringerLink
Log in

Simulation and performance enhancement of the air cooling system in the valve halls of a DC/AC power converter station

  • Research Article/Indoor/Outdoor Airflow and Air Quality
  • Published:
Building Simulation Aims and scope Submit manuscript

Abstract

The present article reports on a ventilation system that uses impinging air jets to remove a portion of the heat generated in DC/AC converter towers. Each tower is a vertical stack of electronic components used in the power conversion. Airflow from the ventilation system enters the room through inlet ports located on the ground at two opposite sides of the DC/AC converter towers. The existing ventilation system circulates sufficient airflow in terms of the total heating load; however, elevated temperatures were reported within the towers due to poor air circulation. A numerical study has been conducted to investigate steady three-dimensional (3-D) turbulent mixed (combined free and forced) convection air cooling of vertical stacks of heat-generating blocks simulating typical towers in two valve halls of a DC/AC power converter station. The simulation results include the magnitudes of the net airflows for all the inter-block gaps, the maximum temperature in each gap, and the flow structure represented by streamlines at various locations of the 3-D domain. The location of the inlet, the inlet size and aspect ratio, and the location on the tower at which the airflow was aimed were varied parametrically to improve the ventilation relative to the existing design. These results demonstrate that, for fixed inlet mass flow rate, all the towers’ heat generating surfaces can be kept under 60°C via simple modifications of the variables used in the parametric study.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

References

  • Arquis E, Rady MA, Nada SA (2007). A numerical investigation and parametric study of cooling an array of multiple protruding heat sources by a laminar slot air jet. International Journal of Heat and Fluid Flow, 28: 787–805.

    Article  Google Scholar 

  • Berg JR, Ormiston SJ, Soliman HM (2006). Prediction of the flow structure in a turbulent rectangular free jet. International Communications in Heat and Mass Transfer, 33: 552–563.

    Article  Google Scholar 

  • Berg JR, Soliman HM, Ormiston SJ (2008a). Effective cooling of stacked heat-generating bodies in a large room: Comparison between floor and side-wall air injection. International Journal of Thermal Science, 47: 787–799.

    Article  Google Scholar 

  • Berg JR, Soliman HM, Ormiston SJ (2008b). Turbulent mixed-convection cooling of stacked heat-generating bodies in a three-dimensional domain. Numerical Heat Transfer, Part A-Applications, 53: 249–272.

    Article  Google Scholar 

  • Bilgen E, Muftuoglu A (2008). Natural convection in an open square cavity with discrete heaters at their optimized positions. International Journal of Thermal Sciences, 47: 369–377.

    Article  Google Scholar 

  • Chang-geng L, Jie-min Z (2007). Experimental and numerical simulation study of heat transfer due to confined impinging circular jet. Chemical Engineering and Technology, 30: 1355–1361.

    Article  Google Scholar 

  • Desrayaud G, Fichera A (2003). On natural convective heat transfer in vertical channels with a single surface mounted heat-flux module. Journal of Heat Transfer, 125: 734–739.

    Article  Google Scholar 

  • Eiamsa-ard S, Promvonge P (2008). Numerical study on heat transfer of turbulent channel flow over periodic grooves. International Communications in Heat and Mass Transfer, 35: 844–852.

    Article  Google Scholar 

  • Elsaadawy E, Mortazavi H, Hamed MS (2008). Turbulent modeling of forced convection heat transfer in two-dimensional ribbed channels. Journal of Electronic Packaging, 130: 1–17.

    Article  Google Scholar 

  • Grotjans H, Menter FR (1998). Wall functions for general application CFD codes. In: ECCOMAS 98’ Proceedings of the Forth European Computational Fluid Dynamics Conference, Athens, Greece, pp. 1112–1117.

  • Hofmann HM, Kaiser R, Kind M, Martin H (2007). Calculations of steady and pulsating impinging jets-an assessment of 13 widely used turbulence models. Numerical Heat Transfer, Part B: Fundamentals, 51: 565–583.

    Article  Google Scholar 

  • Isman MK, Pulat E, Etemoglu AB, Can M (2008). Numerical investigation of turbulent impinging jet cooling of a constant heat flux surface. Numerical Heat Transfer, Part A: Applications, 54: 1109–1132.

    Article  Google Scholar 

  • Koca A (2008). Numerical analysis of conjugate heat transfer in a partially open cavity with a vertical heat source. International Communications in Heat and Mass Transfer, 35: 1385–1395.

    Article  Google Scholar 

  • Launder BE, Spalding DE (1974). The numerical computation of turbulent flows. Computational Methods in Applied Mechanics and Engineering, 3: 269–289.

    Article  Google Scholar 

  • Lozowy RJ (2009). The numerical investigation and parametric study of cooling an array of heated blocks by a turbulent air jet in a three-dimensional domain, M. Sc. thesis, University of Manitoba, Winnipeg, Canada.

    Google Scholar 

  • Lu WZ, Tam CM, Leung AYT, Howarth AT (2002). Numerical Investigation of Convection Heat Transfer in a Heated Room. Numerical Heat Transfer, Part A: Applications, 42: 233–251.

    Article  Google Scholar 

  • Majumdar P, Deb P (2003). Computational analysis of turbulent fluid flow and heat transfer over an array of heated modules using turbulence models. Numerical Heat Transfer, Part A: Applications, 43: 669–692.

    Article  Google Scholar 

  • Merci B, Vierendeel J, Langhe CD, Dick E (2003). Numerical simulation of heat transfer of turbulent impinging jets with two-equation turbulence models. International Journal of Numerical Methods for Heat Transfer and Fluid Flow, 13 (1): 110–132.

    Article  Google Scholar 

  • Patankar SV (1980). Numerical heat transfer and fluid flow. New York: Hemisphere Publishing Corporation.

    MATH  Google Scholar 

  • Quinn WR (1992). Turbulent free jet flows issuing from sharp-edged rectangular slots: The influence of slot aspect ratio. Experimental Thermal and Fluid Science, 5: 203–215.

    Article  Google Scholar 

  • Radhakrishnan TV, Verma AK, Balaji C, Venkateshan SP (2007). An experimental and numerical investigation of mixed convection from a heat generating element in a ventilated cavity. Experimental Thermal and Fluid Science, 32: 502–520.

    Article  Google Scholar 

  • Ramezanpour A, Mirzaee I, Firth D, Shirvani H (2007). A numerical heat transfer study of slot jet impinging on an inclined plate. International Journal of Numerical Methods for Heat and Fluid Flow, 17: 661–676.

    Article  Google Scholar 

  • Ramirez-Iraheta OA, Soliman HM, Ormiston SJ (2006). Effective cooling of vertical heat-generating stacks in a cavity with openings. Heat and Mass Transfer, 42: 398–410.

    Article  Google Scholar 

  • Rao GM, Narasimham GS (2007). Laminar conjugate mixed convection in a vertical channel with heat generating components. International Journal of Heat and Mass Transfer, 50: 3561–3574.

    Article  Google Scholar 

  • Wang SJ, Mujumdar AS (2004). A comparative study of five low Reynolds number k-ε models for impingement heat transfer. Applied Thermal Engineering, 25: 31–44.

    Article  Google Scholar 

  • Yilmaz T, Fraser SM (2007). Turbulent natural convection in a vertical parallel-plate channel with asymmetric heating. International Journal of Heat and Mass Transfer, 50: 2612–2623.

    Article  Google Scholar 

  • Zuckerman N, Lior N (2005). Impingement heat transfer: Correlations and numerical modeling. Journal of Heat Transfer, 127: 544–552.

    Article  Google Scholar 

Download references

Author information

Authors and Affiliations

  1. Department of Mechanical and Manufacturing Engineering, University of Manitoba, Winnipeg, Manitoba, Canada, R3T 5V6

    Richard J. Lozowy, Ahmed M. El-Shaboury, Hassan M. Soliman & Scott J. Ormiston

Authors
  1. Richard J. Lozowy
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Ahmed M. El-Shaboury
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Hassan M. Soliman
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. Scott J. Ormiston
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Hassan M. Soliman.

Rights and permissions

Reprints and permissions

About this article

Cite this article

Lozowy, R.J., El-Shaboury, A.M., Soliman, H.M. et al. Simulation and performance enhancement of the air cooling system in the valve halls of a DC/AC power converter station. Build. Simul. 3, 233–244 (2010). https://doi.org/10.1007/s12273-010-0008-1

Download citation

  • Received:

  • Revised:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s12273-010-0008-1

Keywords

Search

Navigation