Abstract
Slender RC walls are often used in Chile and commonly, due to architectural constraint, the length of walls increases (setback) between floors designated for parking space and upper floors. These types of elements are commonly called flag walls. In this research, the behavior of slender reinforced concrete walls with a constant axial load and a cyclic lateral displacement is numerically studied, in order to compare the results obtained with previous tests. Two different model alternatives are considered: a finite element model and a strut-and-tie model. The selected models allow understanding local response, as well as, distribution of internal forces, which is also relevant information for wall design and detailing. The studied finite element model, based on quadrilateral elements with 3 degrees of freedom per node (2 translational and 1 rotation) and a model of smeared reinforced concrete material based on a rotating angle approach, is able to correctly capture the global response, showing the capacity, degradation and failure mode obtained in the tests. On the other hand, a parametric analysis is performed for models of walls with higher aspect ratio (tall buildings) with small discontinuities, showing a larger impact in deformation capacity due to the high concentration of damage at the discontinuity. These results indicate that in 25-floor high walls (or taller) a reduction of displacement capacity of 40% for discontinuities located at the first floor could be observed. In addition, by incorporating the effect of the slabs into the model, the results indicate that a pure flexure model is an adequate and sufficient tool for analysis. Finally, a strut-and-tie model is also proposed for each direction of the lateral load, whose results are compared with the estimated load calculated with the strains measured by photogrammetry. The considered strut-and-tie model for the case of lateral load with tension in the continuous wall boundary is similar to the wall without discontinuity, which is consistent with the measured strains. For both lateral loading directions, the estimated forces of the horizontally distributed bars and boundary reinforcements are consistent with photogrammetry in the lower zone of the wall, where cracking is relevant. The strut-and-tie model also adequately interprets the effect of the discontinuous bar on the discontinuous boundary of the wall. All these results can help designing and detailing flag walls.
Similar content being viewed by others
References
Ali A, Wight J (1990) Reinforced concrete structural walls with staggered opening configurations under reverse cyclic loading. Report No. UMCE 90-05, Department of Civil Engineering, University of Michigan, Ann Arbor, Michigan
Belarbi A, Hsu TTC (1994) Constitutive laws of concrete in tension and reinforcing bars stiffened by concrete. ACI Struct J 91(4):465–474
Belarbi A, Hsu TTC (1995) Constitutive laws of softened concrete in biaxial tension compression. ACI Struct J 92(5):562–573
Brown MD, Sankovich CL, Bayrak O (2006) Design for shear in reinforced concrete using strut- and-tie models. Ferguson Structural Engineering Lab, University of Texas at Austin, Report No. FHWA/TX-06/0-4371-2
Filippou FC, Popov EG, Bertero VV (1983) Effects of bond deterioration on hysteretic behavior of reinforced concrete joints. UCB/EERC83/19. Earthquake Engineering Research Center, University of California, Berkeley
Kang TH-K, Kim W, Massone LM, Galleguillos TA (2012) Shear–flexure coupling behavior of steel fiber-reinforced concrete beams. ACI Struct J 109(4):435–444
Massone LM (2006) RC wall shear–flexure interaction: analytical and experimental responses. PhD dissertation, University of California, Los Angeles, CA
Massone LM, Alfaro JI (2016) Displacement and curvature estimation for the design of reinforced concrete slender walls. Struct Des Tall Spec Build 25(16):823–841
Massone LM, Moroder D (2009) Buckling modeling of reinforcing bars with imperfections. Eng Struct 31:758–767
Massone LM, Rojas FR, Ahumada MG (2017) Analytical study of the response of reinforced concrete walls with discontinuities of flag-wall type. Struct Concr 18(6):962–973
Massone LM, Díaz S, Manríquez I, Rojas F, Herrera R (2019) Experimental cyclic response of RC walls with setback discontinuities. Eng Struct 178:410–422
Menegotto M, Pinto PE (1973) Method of analysis of cyclically loaded reinforced concrete plane frames including changes in geometry and non-elastic behavior of elements under combined normal force and bending. IABSE symposium on the resistance and ultimate deformability of structures acted on by well-defined repeated loads
Palermo D, Vecchio FJ (2003) Compression field modeling of reinforced concrete subjected to reversed loading: formulation. ACI Struct J 100(5):616–625
Rojas F (2012) Development of a nonlinear quadrilateral layered membrane element with drilling degrees of freedom. PhD dissertation, University of Southern California, Los Angeles, CA
Rojas F, Anderson JC, Massone LM (2016) A nonlinear quadrilateral layered membrane element with drilling degrees of freedom for the modeling of reinforced concrete walls. Eng Struct 124:521–538
Saatcioglu M, Razvi SR (1992) Strength and ductility of confined concrete. J Struct Eng 118(6):1590–1607
Schlaich J, Schafer K, Jennewein M (1987) Toward a consistent design of structural concrete. PCI J 32(3):74–151
Taylor C, Cote P, Wallace J (1998) Design of slender reinforced concrete walls with openings. Technical Paper Title no. 95-S39, ACI Struct J 95(4):420–433
Vecchio FJ (1992) Finite element modeling of concrete expansion and confinement. J Struct Eng 118(9):2390–2406
Acknowledgements
This work was financially supported by FONDECYT regular 2013 No. 1130219 “Analytical and experimental study of RC walls with discontinuities”. Also, the help with the specimens testing by Mr. Ernesto Inzunza, Mr. Victor González and Mr. Pedro Soto are also thanked.
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Massone, L.M., Manríquez, I., Díaz, S. et al. Understanding the cyclic response of RC walls with setback discontinuities through a finite element model and a strut-and-tie model. Bull Earthquake Eng 17, 6547–6563 (2019). https://doi.org/10.1007/s10518-019-00579-3
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s10518-019-00579-3