Abstract
Low-value hardwoods are not used to its full potential because they possess a challenging economic proposition to entrepreneurs in search of profit. In particular, high extraction and processing costs for low-value and underutilized hardwoods are not offset by products that carry a high enough value to customers to assure favorable economics. Thus, the low-value biomass is not used sufficiently in U.S. forests to support sustainable quality forest management practices. Furthermore, economic opportunities are lost for rural economies and forest landowners. The main purpose of the project described is to design the manufacture of a high value product from low-value hardwood timber achieving positive economics, thereby assuring the efficient and effective use of the resource. In particular, the project assesses the markets and the technical potential for manufacturing solid, finger-jointed edge-glued hardwood panels from low-value hardwoods. In fact, the technical feasibility of manufacturing edge-glued panels has been proven and is a major product of wood components manufacturers in the U.S. However, the use of low-value hardwoods for this purpose has not received much attention. This study intends to fill this gap by conducting an exhaustive analysis of secondary sources to assess raw material availability for such panels from low-value hardwoods. Also, appropriate processing routes to achieve competitive target prices while assuring positive economics are investigated.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
Notes
- 1.
A board foot describes a volume of one foot by one foot by one inch.
- 2.
A cord describes a volume of stacked wood 4Â feet high, 8Â feet long, and 4Â feet deep.
- 3.
Yield is the surface ratio between the incoming material and the output of the operation.
- 4.
Grade refers to the quality of the material in trees, logs, and lumber. Grades rank different qualities of material and are widely accepted as standards for trading and value determination in markets.
References
Forbes K (2004) U.S. manufacturing: challenges and recommendations. Bus Econ 39(3):30–37
Associated Press (2008) Hard times hit the U.S. hardwood lumber industry. Associated Press, Charleston
Buehlmann U, Schuler A (2009) The U.S. household furniture industry: status and opportunities. For Prod J 59(9):20–28
Schuler A, Buehlmann U (2003) Identifying future competitive business strategies for the U.S. residential wood furniture industry: benchmarking and paradigm shifts. US Department of Agriculture, Forest Service. Northeastern Research Station, Newton Square, p 19
Grushecky ST et al (2006) Decline in the US furniture industry: A case study of the impacts to the hardwood lumber supply chain. Wood Fiber Sci 38(2):365–376
Cole N (2008) Hardwood sawmills in state feeling strain. Arkansas Democrat Gazette
Reddy S (2008) U.S. factories slash output amid slump. Wall Street J
Schneider H, Shin A (2009) Industrial output falling sharply. Washington Post 2009, Washington, DC
US Forest Service. Forest Inventory and Analysis (2012) [cited 2012 June 27]. http://www.fia.fs.fed.us/
Fajvan MA, Grushecky ST, Hassler CC (1998) The effects of harvesting practices on west virginia’s wood supply. J For 96(5):33–39
Nyland RD (1992) Exploitation and greed in eastern hardwood forests. J For 90(1):33–37
Luppold WG, Bumgardner MS (2008) Timber value issues resulting from harvest activity in appalachian forests. In: Proceedings of 2008 southern forest economics workers annual meeting. Savannah, center for forest business, Warnell School Of Forestry And Natural Resources, University of Georgia, GA
Wiedenbeck JK et al (2003) Small-diameter hardwood utilization with emphasis on higher value products. In: Proceedings of enhancing the southern appalachian forest resource 2003. Department of Forestry, College Of Natural Resources, North Carolina State University
Brown SL, Schroeder P, Kern JS (1999) Spatial distribution of biomass in forests of the eastern USA. For Ecol Manage 123(1):81–90
Miles PD, Van der Schaaf CL (2012) Minnesota’s forest resources, 2011, 2012. U.S. Department of agriculture, Forest Service, Northern Research Station: Newtown Square, PA, p 4
DNR (2010) Minnesota’s Forest Resources 2010, 2011. Department of Natural Resources, Division of Forestry, Saint Paul, p 59
Bumgardner MS et al (2000) Options for small-diameter hardwood utilization: past and present. In: Proceedings of the annual meeting of the southern forest economics workers (SOFEW), hardwoods—an underdeveloped resource, 26–28 Mar 2001 , Lexington
Cumbo D, Smith R, Araman P (2003) Low-grade hardwood lumber production, markets, and issues. For Prod J 53(9):17–24
Cantrell R, Paun D, LeVan-Green S (2004) An empirical analysis of an innovative application for an underutilized resource: small-diameter roundwood in recreational buildings. For Prod J 54(9):28–35
Perkins BR (2006) A business model for a red oak small diameter timber processing facility in southwest Virginia. Wood Science and Forest Products 2006, Virginia Polytechnic Institute and State University, Blacksburg, p 149
Becker DR, Eaton LM (2012) Something old and something new: forest bioenergy production in Minnesota. CURA Reporter 42:8
Levan-Green SL, Livingston J (2001) Exploring the uses for small-diameter trees. For Prod J 51(9):10
WCMA (2011) Wood component manufacturers association 2011 [cited 2011 March 15]. http://woodcomponents.org/
Lawser S (2004) Market outlook for wood components. In: Proceedings of exploring new paths conference 2004, Edmonton, p 31
Bowyer JL et al (1986) Standard blanks: a new alternative to hardwood lumber. For Prod J 36(2):67–73
Lawser S (2009) Changing markets for wood components in remaining competitive in the wood components industry. Princeton, p 25
Tabarsi E et al (2003) A market assessment of the potential for OSB products in the North American office furniture and door manufacturing industries. For Prod J 53(7/8):19–27
McDaniel PWP (2003) Opportunities for the utilization of non-traditional species in wood-based component manufacturing. Wood Science and Forest Products, Virginia Tech, Blacksburg
Deaver ME (2006) Economic feasibility of a solid hardwood panel manufacturing enterprise. Wood and Paper Science, North Carolina State University, Raleigh, p 193
Shepley BP (2002) Simulating optimal part yield from no. 3A common lumber. Wood Science and Forest Products, Virginia Polytechnic Institute and State University, Blacksburg, p 148
Luppold W, Bumgardner M (2003) What is low-value and/or low-grade hardwood? For Prod J 53(3):54
Cumbo DW, Smith RL, Becker Iii CW (2004) Value analysis of lumber produced from small-diameter timber. For Prod J 54(10):29–34
Wengert EM, Meyer DA (1994) Guidelines for grading hardwood logs. University of Wisonsin-Madison, College of Agricultural and Life Sciences, Extension, Madison, p 6
NHLA (2011) National hardwood lumber association. 2011 [cited 2011 March 15]. http://www.nhla.com/
Weiss JM, Thomas RE (2005) ROMI-3: rough-mill simulator version 3.0: user’s guide. U.S. Department of Agriculture, Forest Service, Northeastern Research Station: Newtown Square, p 75
Wiedenbeck JK, Thomas E (1995) Don’t gamble your fortunes—focus on rough mill yield. Wood Wood Prod 100(7):148–149
Mitchell PH, Wiedenbeck J, Ammerman B (2003) Rough mill improvement guide for managers and supervisors. USDA Forest Service, Delaware, p 69
Buelmann U, Wiendenbeck JK, Strasser L (2005) Sawmill—log utilization study. North Carolina State University, Raleigh, p 51
Gephart JS, Petersen HD, Bratkovich SM (1995) Green dimensioning: a review of processing, handling, drying, and marketing. For Prod J 45(5):69–73
Lin W, Kline DE, Araman AP (1994) Dimension yields from factory grade 2 and 3 red oak logs. For Prod J 44(9):19–25
Wenjie L et al (1995) Producing hardwood dimension parts directly from logs: an economic feasibility study. For Prod J 45(6):38–46
Bratkovich SM et al (2000) Green dimensioning below-grade red oak logs: a minnesota case study. For Prod J 50(2):65
Reynolds HW, Schroeder J (1978) Furniture cuttings made from logging residue: the three-sided cant system. U.S. Department of Agriculture, Forest Service, Northeastern Forest Experiment Station, Broomall, p 4
Araman PA (1982) Rough-part sizes needed from lumber for manufacturing furniture and kitchen cabinets. United States Department of Agriculture, Forest Service, Northeast Forest Experiment Station, p 8
Araman PA, Gatchell CJ, Reynolds HW (1982) Meeting the solid wood needs of the furniture and cabinet industries: standard-size hardwood blanks. United States Department of Agriculture, Forest Service, Northeast Forest Experiment Station, p 27
Reynolds HW, Gatchell CJ (1982) New technology for low-grade hardwood utilization: system 6. U.S. Department of Agriculture, Forest Service, Northeastern Research Station, Broomall, p 8
Reynolds HW, Araman PA (1983) System 6: making frame-quality blanks from white oak thinnings. U.S. Department of Agriculture, Forest Service, Northeastern Forest Experiment Station, Broomall, p 9
Buehlmann U et al (2010) Trends in the US hardwood lumber distribution industry: changing products, customers, and services. For Prod J 60(6):547–553
Espinoza O et al (2011) Assessing changes in the U.S. hardwood sawmill industry with a focus on markets and distribution. BioResources 6(3):2676–2689
Mihm J (2010) Incentives in new product development projects and the role of target costing. Manage Sci 56(8):1324–1344
Feil P, Yook K-H, Kim I-W (2004) Japanese target costing: a historical perspective. Int J Strateg Cost Manag 2004(Spring):10–19
Prasad B (1996) Concurrent engineering fundamentals—integrated product and process organization. Prentice Hall, Upper Saddle River
Gatchell CJ, Thomas RE, Walker ES (1998) Data bank for kiln-dried red oak lumber. United States Department of Agriculture, Forest Service, Northeastern Research Station. p 64
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2013 Springer International Publishing Switzerland
About this paper
Cite this paper
Espinoza, O., Buehlmann, U., Deaver, M. (2013). Solid Wood Panel Manufacturing Using Low Quality Materials. In: Azevedo, A. (eds) Advances in Sustainable and Competitive Manufacturing Systems. Lecture Notes in Mechanical Engineering. Springer, Heidelberg. https://doi.org/10.1007/978-3-319-00557-7_9
Download citation
DOI: https://doi.org/10.1007/978-3-319-00557-7_9
Published:
Publisher Name: Springer, Heidelberg
Print ISBN: 978-3-319-00556-0
Online ISBN: 978-3-319-00557-7
eBook Packages: EngineeringEngineering (R0)