Abstract
The current work describes the development of a numerical model to accurately predict the occurrence of various defects during FSW of pure copper using thermomechanical responses. The developed numerical model examines the effect of varying tool dimensions on thermomechanical responses and defect formation. The tool traverse and rotation speed are kept constant at 30 mm/min and 1200 rpm. The shoulder diameter is varied between 14 and 28 mm. The 14 mm tool produces an imperfect weld with surface and sub-surface tunnel defects, whereas the 18 mm tool eliminates the surface tunnel defect. An increase of the shoulder diameter to 28 mm further reduces the extent of sub-surface tunnel defect. The increase in the shoulder diameter eliminates the surface tunnel and reduces the height of the sub-surface tunnel by about 50%. Significant material velocity, strain rate, and temperature on the retreating side (RS) produces the sub-surface tunnel defect on the advancing side (AS). The model can predict the initiation and advancement of the tunnel defect along the welding length. The velocity profile indicates that the material is equally distributed between the AS and RS behind the tool at the conclusion of the dwell stage. Alternatively, the material deposition becomes unequal between the AS and RS as the tool starts traversing. The tool–workpiece interface observes less stress and alternatively high strain, strain rate, and velocity distribution compared to the rest of the workpiece.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Sahlot P, Singh AK, Badheka VJ, Arora A (2019) Friction stir welding of copper: numerical modeling and validation. Trans Indian Inst Met 72:1339–1347
Lin JW, Chang HC, Wu MH (2014) Comparison of mechanical properties of pure copper welded using friction stir welding and tungsten inert gas welding. J Manuf Process 16:296–304
Lee WB, Jung SB (2004) The joint properties of copper by friction stir welding. Mater Lett 58:1041–1046
Mishra RS, Ma ZY (2005) Friction stir welding and processing. Mater Sci Eng R Rep 50:1–78
Zhang Z, Zhang HW (2009) Numerical studies on controlling of process parameters in friction stir welding. J Mater Process Technol 209:241–270
Xue P, Xie GM, Xiao BL, Ma ZY, Geng L (2010) Effect of heat input conditions on microstructure and mechanical properties of friction-stir-welded pure copper. Metall Mater Trans A Phys Metall Mater Sci 41:2010–2021
Shen JJ, Liu HJ, Cui F (2010) Effect of welding speed on microstructure and mechanical properties of friction stir welded copper. Mater Des 31:3937–3942
Sakthivel T, Mukhopadhyay J (2007) Microstructure and mechanical properties of friction stir welded copper. J Mater Sci 42:8126–8129
Farrokhi H, Heidarzadeh A, Saeid T (2013) Frictions stir welding of copper under different welding parameters and media. Sci Technol Weld Join 18:697–702
Arora A, De A, Debroy T (2011) Toward optimum friction stir welding tool shoulder diameter. Scr Mater 64:9–12
Mehta M, Arora A, De A, Debroy T (2011) Tool geometry for friction stir welding - Optimum shoulder diameter. Metall Mater Trans A Phys Metall Mater Sci 42:2716–2722
Khodaverdizadeh H, Heidarzadeh A, Saeid T (2013) Effect of tool pin profile on microstructure and mechanical properties of friction stir welded pure copper joints. Mater Des 45:265–270
Kumar A, Raju LS (2012) Influence of tool pin profiles on friction stir welding of copper. Mater Manuf Process 27:1414–1418
Akbari M, Ezzati M, Asadi P (2022) Investigation of the effect of tool probe profile on reinforced particles distribution using experimental and CEL approaches. Int J Light Mater Manuf 5:213–223
Das D, Bag S, Pal S (2021) Investigating surface defect by tool-material interaction in friction stir welding using coupled Eulerian-Lagrangian approach. Manuf Lett 30:23–26
Al-Badour F, Merah N, Shuaib A, Bazoune A (2014) Thermo-mechanical finite element model of friction stir welding of dissimilar alloys. Int J Adv Manuf Technol 72:607–617
Pashazadeh H, Masoumi A, Teimournezhad J (2013) Numerical modelling for the hardness evaluation of friction stir welded copper metals. Mater Des 49:913–921
Patel NP, Parlikar P, Singh Dhari R, Mehta K, Pandya M (2019) Numerical modelling on cooling assisted friction stir welding of dissimilar Al-Cu joint. J Manuf Process 47:98–109
Gotawala N, Shrivastava A (2020) Analysis of material distribution in dissimilar friction stir welded joints of Al 1050 and copper. J Manuf Process 57:725–736
Aliha MRM, Kalantari MH, Ghoreishi SMN, Torabi AR, Etesam S (2019) Mixed mode I/II crack growth investigation for bi-metal FSW aluminum alloy AA7075-T6/pure copper joints. Theor Appl Fract Mech 103:102243
Das D, Bag S, Pal S, Ruhul Amin M (2020) Prediction of surface profile in friction stir welding using coupled eulerian and lagrangian method. In: ASME international mechanical engineering congress and exposition, proceedings (IMECE). p V011T11A035. ASME
Akbari M, Asadi P, Behnagh RA (2021) Modeling of material flow in dissimilar friction stir lap welding of aluminum and brass using coupled Eulerian and Lagrangian method. Int J Adv Manuf Technol 113:721–734
Ragab M, Liu H, Yang GJ, Ahmed MMZ (2021) Friction stir welding of 1Cr11Ni2W2MoV martensitic stainless steel: numerical simulation based on coupled Eulerian Lagrangian approach supported with experimental work. Appl Sci 11:1–18
Neto DM, Neto P (2013) Numerical modeling of friction stir welding process: a literature review. Int J Adv Manuf Technol 65:115–126
Das D, Bag S, Pal S, Ruhul Amin M (2021) A finite element model for the prediction of chip formation and surface morphology in friction stir welding process. J Manuf Sci Eng 144:041015
Wen Q, Li WY, Gao YJ, Yang J, Wang FF (2019) Numerical simulation and experimental investigation of band patterns in bobbin tool friction stir welding of aluminum alloy. Int J Adv Manuf Technol 100:2679–2687
Das D, Bag S, Pal S, Sharma A (2023) Material Defects in friction stir welding through thermos—mechanical simulation : dissimilar materials with tool wear consideration. Materials (Basel). 16:301 (2023)
Das D, Bag S, Pal S (2021) A finite element model for surface and volumetric defects in the FSW process using a coupled Eulerian-Lagrangian approach. Sci Technol Weld Join 26:412–419
Liu H, Zhang J, Xu X, Qi Y, Liu Z, Zhao W (2019) Effects of dislocation density evolution on mechanical behavior of OFHC copper during high-speed machining. Materials (Basel) 12:1–18
Zhang X, Li L, Pan T, Chen Y, Zhang Y, Li W, Liou F (2020) Additive manufacturing of copper-tool steel dissimilar joining: experimental characterization and thermal modeling. Mater Charact 170:110692
Malarvizhi S, Balasubramanian V (2012) Influences of tool shoulder diameter to plate thickness ratio (D/T) on stir zone formation and tensile properties of friction stir welded dissimilar joints of AA6061 aluminum-AZ31B magnesium alloys. Mater Des 40:453–460
Sevvel P, Jaiganesh V (2015) Effect of tool shoulder diameter to plate thickness ratio on mechanical properties and nugget zone characteristics during FSW of dissimilar mg alloys. Trans Indian Inst Met 68:41–46
Acknowledgements
The authors gratefully acknowledge the support from Science and Engineering Research Board, Government of India (grant no. MTR/2020/000328 dated 11.01.2021) for providing the computational facility.
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2024 The Author(s), under exclusive license to Springer Nature Singapore Pte Ltd.
About this paper
Cite this paper
Das, D., Bag, S., Pal, S. (2024). Finite Element Simulation of Tunnel Defect in Friction Stir Welding of Pure Copper: Effect of Tool Geometry. In: Tambe, P., Huang, P., Jhavar, S. (eds) Advances in Mechanical Engineering and Material Science. ICAMEMS 2023. Lecture Notes in Mechanical Engineering. Springer, Singapore. https://doi.org/10.1007/978-981-99-5613-5_24
Download citation
DOI: https://doi.org/10.1007/978-981-99-5613-5_24
Published:
Publisher Name: Springer, Singapore
Print ISBN: 978-981-99-5612-8
Online ISBN: 978-981-99-5613-5
eBook Packages: EngineeringEngineering (R0)