Abstract
In wire electrical discharge machining (WEDM), material is removed by means of the rapid and cyclic spark that discharges across the gap between the tool and workpiece. In the present work, process parameters of WEDM are tried to be optimize the response variable on Stainless Steel-316 alloy material. SS-316 combinations have been broadly utilized for their predominant properties. For example, high quality, high electrical and thermal conductivities, and low cost. The input parameters considered are pulse-on time, pulse-off time, and current to optimize the responses, viz. surface roughness (SR), volumetric material removal rate (VMRR), dimensional error (DE), and electrode wear (EW). Taguchi’s L27 orthogonal array was chosen to conduct the experiments according to design of experiments (DOE). SR is measured using surftron surface tester and VMRR is calculated based on machining time. DE and EW are measured by micrometer. By using artificial neural network, results were predicted and compared with the experimental results.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
Similar content being viewed by others
References
Liao, Y.S., Huang, J.T., Su, H.C.: A study on the machining parameters optimization wire electrical discharge machining. J. Mater. Process. Technol. 71, 487–493 (1997)
Ravindranadh, B., Madhu, V., Gogia, A.K.: Effect of wire-EDM machining parameters on surface roughness and material removal rate of high strength armor steel. Mater. Manuf. Process. 28, 1–5 (2013)
Liao, Y.S., Huang, J.T., Chen, Y.H.: A study to achieve a fine surface finish in wire-EDM. J. Mater. Process. Technol. 149, 165–171 (2004)
Ugrasen, G., Ravindra, H.V., Naveen Prakash, G.V., Teertha Prasad, Y.N.: Optimization of process parameters in wire EDM of HCHCr material using Taguchi’s technique. Mater. Today Proc. 2, 2443–2452 (2015)
Ugrasen, G., Ravindra, H.V., Naveen Prakash, G.V., Keshavamurthy, R.: Process optimization and estimation of machining performances using artificial neural network in wire EDM. Procedia Mater. Sci. 6, 1752–1760 (2014)
Wang, Kesheng: A hybrid intelligent method for modelling the EDM process. Int. J. Mach. Tools Manuf. 43, 995–999 (2003)
Shandilya, P., Jain, P.K., Jain, N.K.: Parametric optimization during wire electrical discharge machining using response surface methodology. Procedia Eng. 38, 2371–2377 (2012)
Kumar, A., Kumar, A., Kumar, J.: Prediction of surface roughness in wire electric discharge machining (WEDM) process based on response surface methodology. Int. J. Eng. Technol. 2(4), 708–719 (2012)
Huang, J.T., Liao, Y.S.: Optimization of machining parameters of wire-EDM based on grey relational and statistical analyses. Int. J. Prod. Res. 41, 1707–1720 (2003)
Tosun, N., Cogun, C., Tosun, G.: A study on kerf and material removal rate in wire electrical discharge machining based on Taguchi method. J. Mater. Process. Technol. 154, 316–322 (2004)
Acknowledgements
The work reported in this paper is supported by B.M.S. College of Engineering, through the Technical Education Quality Improvement Programme [TEQIP-III] of the MHRD, Government of India.
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2020 Springer Nature Singapore Pte Ltd.
About this paper
Cite this paper
Ugrasen, G., Rakesh, D., Ravindra, H.V., Guruprasad, K., Singu, S.M.R. (2020). Prediction of Machining Responses in Wire EDM on Stainless Steel-316. In: Shunmugam, M., Kanthababu, M. (eds) Advances in Simulation, Product Design and Development. Lecture Notes on Multidisciplinary Industrial Engineering. Springer, Singapore. https://doi.org/10.1007/978-981-32-9487-5_33
Download citation
DOI: https://doi.org/10.1007/978-981-32-9487-5_33
Published:
Publisher Name: Springer, Singapore
Print ISBN: 978-981-32-9486-8
Online ISBN: 978-981-32-9487-5
eBook Packages: EngineeringEngineering (R0)