Abstract
There is a burgeoning use of reactive powder concrete unsettled to the outstanding mechanical properties and resilience. Reactive powder concrete structural elements can resist chemical paroxysm, impact loading from vehicles and vessels, and sudden kinetic loading due to earthquakes. In addition, the lower maintenance requirements result in significant economic detriment. Moreover, in the composition of reactive powder concrete, a fractional substitution of cement by silica fume (which is a waste by-product of silicon alloy) results in less cement consumption (and hence less greenhouse gas emission). In this experimental investigation study, the material performance of reactive powder concrete (RPC) with two different curing techniques, normal water curing of 25 °C and accelerated steam curing at 60 °C, and 60% relative humidity, was studied experimentally. This paper also remits the investigation, application, and different preparation of silica fume in reactive powder concrete at transformed temperature. The silica fume was substituted with the cement and the dosage which bequeathed the maximum strength was used for further addition of silica sand and steel fibers. Steam curing is effective process to achieve high early strength, and in this narrative, the compressive strength at the age of 3, 7, and 28 days was determined for further compared with normal cured water. Also find split tensile test to see the performance of concrete cylinder under tension. To reduce the water content, super plasticizer may be used as an admixture. Thus, results are interpreted for different combination to achieve maximum compressive stress as well as tensile stress.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Roux N, Andrade C, Sanjuan MA (1996) Experimental study of durability of reactive powder concretes. J Mater Civil Eng (ASCE) 8:1–6
Chan Y-W, Chu S-H (2004) Effect of silica fume on steel fiber bond characteristics in reactive powder concrete. Cem Concr Res (Sci Direct Pergamon) 34:1167–1172
Chang TP, Chen BT, Wang JJ, Wu CS (2009) Performance of reactive powder concrete (RPC) with different curing conditions and its retrofitting effects on concrete member. In: Alexander et al (eds) Concrete repair, rehabilitation and retrofitting II. Taylor and Francis group, London. ISBN: 978-0-415-46850-3
Hoe KW, Ramli M (2010) Rational mix design approach for high strength concrete using sand with very high fineness modulus. Am J Appl Sci 7(12):1562–1568. ISSN: 1546-9239
Tai YS, Pan HH, Kung YN (2011) Mechanical properties of steel fiber reinforced reactive powder concrete following exposure to high temperature reaching 800 °C. Nucl Eng Des 241(7):2416–2424
IS: 2250 (1981) Code of practice for preparation and use of masonry mortars. Bureau of Indian Standards, New Delhi
IS: 8112 (1989) Ordinary Portland cement, 43 grade—specification. Bureau of Indian Standards, New Delhi
Khalil WI (2012) Some properties of modified reactive powder concrete. J. Eng. Dev 16(4):66–87. ISSN: 1813-7822
Yu R, Spiesz P, Brouwers HJH (2014) Mix design and properties assessment of ultra-high performance fibre reinforced concrete (UHPFRC)”. Cem Concr Res 56:29–39
Tam CM, Tam VWY, Ng KM (2010) Optimal conditions for producing reactive powder concrete. Mag Concr Res 62:701–716
IS: 4031 (1988) (part 11) Methods of physical tests for hydraulic cement part ii determination of density. Bureau of Indian Standards, New Delhi
IS: 10262 (1999) Recommended guidelines for concrete mix design. Bureau of Indian Standards, New Delhi
IS: 383 (1970) Specification for coarse and fine aggregates from natural sources for concrete. Bureau of Indian Standards, New Delhi
Zdeb T (2013) Ultra-high performance concrete—properties and technology. Bull Pol Acad Sci Tech Sci 61(1):183–193
Kizilkanat AB, Oktay D, Kabay N, Tufekci MM (2016) Comparative experimental study of mortars incorporating pumice powder or fly ash. J Mater Civ Eng 28(2):1–7. (04015119)
IS: 3812 (1963) (part 1) Pulverized fuel ash specification part 1 for use as pozzolana in cement, cement mortar and concrete. Bureau of Indian Standards, New Delhi
IS: 3812 (2003) (part 2) Pulverized fuel ash—specification part 2 for use as admixture in cement mortar and concrete. Bureau of Indian Standards, New Delhi
Chung DDL (2005) Dispersion of short fibers in cement. J Mater Civ Eng 17(4):379–383
Carroll JC, Helminger N (2016) Fresh and hardened properties of fiber-reinforced rubber concrete. J Mater Civ Eng 28(7):1–9. (04016027)
Alkafaji MMK (2014) Performance of reactive powder concrete slabs with different curing conditions. J Eng Technol Res 6(6):81–93. ISSN: 2006-9790
Way RT, Wille K (2016) Effect of heat-induced chemical degradation on the residual mechanical properties of ultrahigh-performance fiber-reinforced concrete. J Mater Civ Eng 28(4):1–10. (04015164)
IS: 456 (2000) Plain and reinforced concrete-code of practice. Bureau of Indian Standards, New Delhi
IS: 516 (1959) Methods of tests for strength of concrete. Bureau of Indian Standards, New Delhi
IS: 2386 (1963) Indian standard code of practice for methods of test for aggregate for concrete. Indian Standard Institution, New Delhi
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2021 Springer Nature Singapore Pte Ltd.
About this paper
Cite this paper
Sonkusare, H.G., Pawade, P.Y. (2021). Investigate the Temperature Effects on Curing of Reactive Powder Concrete Containing Silica. In: Gupta, L.M., Ray, M.R., Labhasetwar, P.K. (eds) Advances in Civil Engineering and Infrastructural Development. Lecture Notes in Civil Engineering, vol 87. Springer, Singapore. https://doi.org/10.1007/978-981-15-6463-5_71
Download citation
DOI: https://doi.org/10.1007/978-981-15-6463-5_71
Published:
Publisher Name: Springer, Singapore
Print ISBN: 978-981-15-6462-8
Online ISBN: 978-981-15-6463-5
eBook Packages: EngineeringEngineering (R0)