Abstract
Lightweight thermoplastics are the most prominent concerns of manufacturers due to their high performance characteristics in the current trend. Weld strength and weld quality are the performance measures of the thermoplastic materials, and determining the optimum weld parameters is the major research problem. This paper presents the optimization of weld parameters required for friction stir welding (FSW) of silicon carbide and aluminum reinforced in high-density polyethylene. The improved mechanical properties of these composites are the resultant effects of the optimum process parameters like welding speed, rotational speed, tilt angle, and percentage of reinforcement; hence it is very essential to determine them and to study their influence on composites weld joint. The experimental analysis was carried out for three levels in each and different combinations of weld parameters in order to measure the tensile strength and hardness. The optimum set of nine experiments was designed based on L9 Taguchi’s design. The elicited test results convey that rotation speed of the tool is the most influential weld parameter for tensile strength and weld speed is the most responsible for hardness response of FSW butt joint. Maximum weld strength is 74.66% of the base material and hardness of 41.90 BHN at the weld portion is obtained. The analysis reveals that the added silicon carbide and aluminum particles enhance the ductility and brittle characteristics to base HDPE sheet causing improved weld strength and in turn ensures the weld quality.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Zohoor M, Besharati Givi MK, Salami P (2012) Effect of processing parameters on fabrication of Al-Mg/Cu composites via friction stir processing. Mater Des 39:358–365
Aydin M (2010) Effects of welding parameters and pre-heating on the friction stir welding of UHMW-polyethylene. Polym Plast Technol Eng 49(6):595–601
Bilici MK, Yükler AI, Kurtulmuş M (2011) The optimization of welding parameters for friction stir spot welding of high density polyethylene sheets. Mater Des 32(7):4074–4079
Arici A, Sinmazcelik T (2005) Effects of double passes of the tool on friction stir welding of polyethylene. J Mater Sci 40:3313–3316
Nandan R, DebRoy T, Bhadeshia HKDH (2008) Recent advances in friction-stir welding—process, weldment structure and properties. Prog Mater Sci 53(6):980–1023
Casalino G, Campanelli S, Mortello M (2014) Influence of shoulder geometry and coating of the tool on the friction stir welding of aluminium alloy plates. Procedia Eng 69:1541–1548
Hwang YM, Kang ZW, Chiou YC, Hsu HH (2008) Experimental study on temperature distributions within the workpiece during friction stir welding of aluminum alloys. Int J Mach Tools Manuf 48(7–8):778–787
Amancio-Filho ST, Sheikhi S, dos Santos JF, Bolfarini C (2008) Preliminary study on the microstructure and mechanical properties of dissimilar friction stir welds in aircraft aluminium alloys 2024-T351 and 6056-T4. J Mater Process Technol 206(1–3):132–142
Balasubramanian V (2008) Relationship between base metal properties and friction stir welding process parameters. Mater Sci Eng A 480(1–2):397–403
Liu P, Shi Q, Wang W, Wang X, Zhang Z (2008) Microstructure and XRD analysis of FSW joints for copper T2/aluminium 5A06 dissimilar materials. Mater Lett 62(25):4106–4108
Kwon YJ, Shigematsu I, Saito N (2008) Dissimilar, Friction stir welding between magnesium and aluminum alloys. Mater Lett 62(23):3827–3829
Serindag H, Serindag HT, Kiral BG (2016) Friction stir welding of Az31 magnesium alloys—a numerical and experimental study. Latin Am J Solids Struct 14(1):113–130
Bretz GT, Lazarz KA, Hill DJ, Blanchard PJ (2014) Adhesive bonding and corrosion protection of a die cast magnesium automotive door. Essent Readings Magnes Technol 9781118858:609–615
Park SHC, Sato YS, Kokawa H (2003) Effect of micro-texture on fracture location in friction stir weld of Mg alloy AZ61 during tensile test. Scr Mater 49(2):161–166
Sahu SK, Mishra D, Mahto RP, Pal SK, Pal K (2016) Friction stir welding of HDPE sheets: a study on the effect of rotational speed, ISBN: 978-93-86256-27-0, pp 1065–1068
Kurabe Y, Miyashita Y, Hori H (2017) Joining process and strength in PVC friction stir spot welding with fabricating composite material at welding area. Weld Int 31(5):354–362
Saeedy S, Givi MKB (2011) Investigation of the effects of critical process parameters of friction stir welding of polyethylene. Proc Inst Mech Eng Part B: J Eng Manuf 225(8):1305–1310
Panneerselvam K, Lenin K (2014) Joining of Nylon 6 plate by friction stir welding process using threaded pin profile. Mater Des 53:302–307
Bagheri A, Azdast T, Doniavi A (2013) An experimental study on mechanical properties of friction stir welded ABS sheets. Mater Des 43:402–409
Bilici MK (2012) Application of Taguchi approach to optimize friction stir spot welding parameters of polypropylene. Mater Des 35:113–119
Yousefpour A, Hojjati M, Immarigeon JP (2004) Fusion bonding/welding of thermoplastic composites. J Thermoplast Compos Mater 17:303–341
Kiss Z, Czigány T (2012) Microscopic analysis of the morphology of seams in friction stir welded polypropylene. Expr Polym Lett 6(1):54–62
Payganeh GH, Arab NBM, Asl YD, Ghasemi FA, Boroujeni MS (2011) Effects of friction stir welding process parameters on appearance and strength of polypropylene composite welds. Int J Phys Sci 6(19):4595–4601
Dashatan SH, Azdast T, Ahmadi SR, Bagheri A (2013) Friction stir spot welding of dissimilar polymethyl methacrylate and acrylonitrile butadiene styrene sheets. Mater Des 45:135–141
Raza K, Shamir M, Qureshi MKA, Shaikh AS, Zain-ul-abdein M (2018) On the friction stir welding, tool design optimization, and strain rate-dependent mechanical properties of HDPE–ceramic composite joints. J Thermoplast Compos Mater 31(3):291–310
Emamian S, Awang M, Yusof F (2017). A review of friction stir welding pin profile 1–18. https://doi.org/10.1007/978-981-10-4232-4
Rezaee Hajideh M, Farahani M, Alavi SAD, Molla Ramezani N (2017) Investigation on the effects of tool geometry on the microstructure and the mechanical properties of dissimilar friction stir welded polyethylene and polypropylene sheets. J Manuf Processes 26:269–279
Singh R, Kumar V, Feo L, Fraternali F (2016) Experimental investigations for mechanical and metallurgical properties of friction stir welded recycled dissimilar polymer materials with metal powder reinforcement. Compos B Eng 103:90–97
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2020 Springer Nature Singapore Pte Ltd.
About this paper
Cite this paper
Ramesh Babu, S., Hudgikar, S.R.K., Poornachandra Sekhar, Y. (2020). Experimental Investigation on Friction Stir Welding of HDPE Reinforced with SiC and Al and Taguchi-Based Optimization. In: Voruganti, H., Kumar, K., Krishna, P., Jin, X. (eds) Advances in Applied Mechanical Engineering. Lecture Notes in Mechanical Engineering. Springer, Singapore. https://doi.org/10.1007/978-981-15-1201-8_99
Download citation
DOI: https://doi.org/10.1007/978-981-15-1201-8_99
Published:
Publisher Name: Springer, Singapore
Print ISBN: 978-981-15-1200-1
Online ISBN: 978-981-15-1201-8
eBook Packages: EngineeringEngineering (R0)