Abstract
Friction stir processing (FSP) has proven to be a powerful emerging surface engineering technology for modifying metal surfaces and their bulk properties to desired forms. As a variant of friction stir welding (FSW), FSP borrows its principles of functionality from FSW. FSP technology is highly dependent on careful selection of process parameters. Its key parameters include tool rotational speed, traverse speed, tool tilt angles, axial force, tool and process design as well as base metal properties. Formation of excessive flash is a common FSP parametric challenge which needs to be studied. In this work, build-up of mass flash was experimentally observed and controlled by varying process tool tilt angle and the rotational during FSP of AA1100. The process was conducted using H13 tool steel cylindrical tool with a shoulder diameter of 21 mm with a 7 mm cylindrical threaded pin, at constant traverse speed of 20 mm/min at tilt angles varying from 0° to 3°, rotational speeds of 500 to 1500 rpm for unreinforced process and 2100–2800 rpm for reinforced process, at constant plunge depth of 0.2 mm, and traverse force of 11.2 kN. Results obtained from the physically examined FSP’ed samples show that excessive flash was generated for tilt angles from 0° to 2° as a result of limited under-shoulder space for flow of the plasticized material and the front tip of the tool digging into the base metal ejecting material from the processed zone. Massive flash reduction was observed at 2.5°. A further improvement of flash reduction was witnessed at 3° tilt angle but with reduced shoulder-to-base metal areal contact due to too much raised tool front.
This is a preview of subscription content, log in via an institution.
Buying options
Tax calculation will be finalised at checkout
Purchases are for personal use only
Learn about institutional subscriptionsReferences
Kiran AU, Pravala EK (2017) Experimental investigations on tribiological properties of 6061-T6 Al alloy by via friction stir processing. Int J Adv Eng Manag Sci (IJAEMS) 3(10):995–1000
García-Vázquez F, Vargas-Arista B, Muñiz R, Ortiz JC, García HH (2017) The role of friction stir processing (FSP) parameters on TiC reinforced surface Al7075-T651 aluminum alloy. Corporación Mexicana de Investigación en Materials—COMIMSA. Saltillo, México 21(4):508–516
Chainarong S, Muangjunburee P, Suthummanon S (2014) Friction stir processing of SSM356 aluminium alloy. In 12th Global Congress on Manufacturing and Management, GCMM 2014, Thailand
Węglowski M (2014) Microstructural characterisation of friction stir processed cast AlSi9Mg aluminium alloy. Arch Foundry Eng 14(3):75–78
Sairam SGNV, Madhu S (2015) A review on friction stir processing on aluminum based materials. Int J Appl Eng Res 10(33):25462–25467
Chan CY (2011) A doctoral thesis: friction stir processing of aluminium-silicon alloys. University of Manchester, London
Miranda RM, Gandra J, Vilaça P (2013) Surface modification by friction based processes. In: Morden surface engineering treatments, Lisbon, INTECH, 2013, pp 1–20
Kumar VM, Kumar RS, Vishnuadhithya U, Raj SJP, Kumar PS, Franklin SB (2017) Fabrication of aluminum surface composite by friction stir processing—a review. SSRG Int J Mech Eng (ICET’17) 17:15–19
Zhang YN, Cao X, Larose S, Wanjara P (2012) Review of tools for friction stir welding and processing. Can Metall Q 51(3):250–261
Akinlabi ET, Mahamood RM, Ogunmuyiwa E (2014) Process parameters influence on wear resistance behaviour of friction stir processed Al-TiC composites. Adv Mater Sci Eng 2014:1–12
Amirtharaj D, Rajamurugan G, Sivachidambaram S, Dinesh D (2015) Effect of tool geometryon surface modification of aluminium 6063 by friction stir processing. J Eng Appl Sci, ARPN 10(12):5391–5394
Cartigueyen S, Mahadevan K (2014) Study of friction stir processed zone under different tool pin profiles in pure copper. IOSR J Mech Civil Eng (IOSR-JMCE) 70(3):6–12
Wadekar W, Soladhra R, Barkade H, Thombare N (2017) A review on friction stir technology. Int Conf Ideas, Impact Innov Mech Eng (ICIIIME 2017) 5(6):1542–1549
Yang W, Ding H, Mu Y, Li J, Zhang W (2017) Achieving high strength and ductility in double-sided friction stir processing 7050-T7451 aluminum alloy. Mater Sci Eng, A 707:193–198
Nadammal N, Kailas SV, Szpunar J, Suwas S (2018) Development of microstructure and texture during single and multiple pass friction stir processing of a strain hardenable aluminium alloy. Mater Charact 140:134–146
Navaser M, Atapour M (2017) Effect of friction stir processing on pitting corrosion and intergranular attack of 7075 aluminum alloy. J Mater Sci Technol 33:155–165
Akinlabi ET, Akinlabi SA (2016) Effect of rotational speed on joint integrity of friction stir lap welded aluminium. In: Proceedings of the world congress on engineering 2016, vol II. (WCE 2016), London, UK
Gnanavel JPL, Vijayan S (2017) Friction stir processing of magnesium alloys—review. J Chem Pharm Sci 7:121–126
Hariharan R, Golden Renjith Nimal RJ (2014) Friction stir welding of dissimilar aluminium alloys (6061&7075) by using computerized numerical control machine. Middle-East J Sci Res 20(5):601–605
Vepakomma H (2006) Masters thesis: three dimensional thermal modeling of friction stir processing. Florida State University, Florida, USA
Anglada CS (2006) A final degree project: friction stir processing, a new microstructure improvement technique. Universitat de Girona, Spain
Langlade C, Roman A, Schlegel D, Gete E, Noel P, Folea M (2017) Influence of friction stir process parameters on surface quality of aluminum alloy A2017. In: International conference on computing and solutions in manufacturing engineering, CoSME’16, Belfort Cedex
Sun N, Apelian D (2014) Friction stir processing of aluminum cast alloys for high performance applications. JOM 63(11):44–50
Kumar S (2016) Ultrasonic assisted friction stir processing of 6063 aluminum alloy. Arch Civil Mech Eng 16:473–484
Izadi H, Nolting A, Munro C, Bishop DP, Plucknett KP, Gerlich AP (2013) Friction stir processing of Al/SiC composites fabricated by powder metallurgy. J Mater Process Technol 213:1900–1907
John J, Shanmughanatan SP, Kiran MB (2018) Effect of tool geometry on microstructure and mechanical properties of friction stir processed AA2024-T351 aluminium alloy. Mater Today Proceedings 5:2965–2979
Khodabakhshi F, Simchi A, Kokabi AH, Švec P, Simančík F, Gerlich AP (2015) Effects of nanometric inclusions on the microstructural characteristics and strengthening of a friction-stir processed aluminum–magnesium alloy. Mater Sci Eng, A 642:215–229
Hannard F, Castin S, Maire E, Mokso R, Pardoen T, Simar A (2017) Ductilization of aluminium alloy 6056 by friction stir processing. Acta Mater 130:121–136
Moustafa EB, Mohammed S, Abdel-Wanis S, Mahmoud T, El-Kady E (2017) Surface composites defects of Al/Al2O3 Metal matrix fabricated by friction stir. J Mater Sci Surf Eng 5(2):524–527
Huang G, Hou W, Shen Y (2018) Evaluation of the microstructure and mechanical properties of WC particle reinforced aluminum matrix composites fabricated by friction stir processing. Mater Charact 138:26–37
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2020 Springer Nature Singapore Pte Ltd.
About this paper
Cite this paper
Marazani, T., Akinlabi, E.T., Madyira, D.M. (2020). Reduction of Excessive Flash in Friction Stir Processing of AA1100: An Experimental Observation Study. In: Awang, M., Emamian, S., Yusof, F. (eds) Advances in Material Sciences and Engineering. Lecture Notes in Mechanical Engineering. Springer, Singapore. https://doi.org/10.1007/978-981-13-8297-0_32
Download citation
DOI: https://doi.org/10.1007/978-981-13-8297-0_32
Published:
Publisher Name: Springer, Singapore
Print ISBN: 978-981-13-8296-3
Online ISBN: 978-981-13-8297-0
eBook Packages: EngineeringEngineering (R0)