Abstract
Copper T2 thin sheet thickness of 2 mm by vacuum electron beam welding, scanning electron microscopy, optical microscopy, microhardness tester, and tensile testing machine was used. The formation of the weld surface by different scanning methods was studied. The influence of cross section morphology and microhardness of welded joints and The Effect of microstructure on mechanical properties of the welded joint. The results showed that in working distance is 300 mm and the accelerating voltage U = 60 kV, focusing current If = 502 mA, welding speed V = 800 mm/min and electron beam flow Ib = 27 mA situation, without the addition of scanning, the welded joint with good forming and no macroscopic defects can be obtained. Under the same conditions contrast to add the scanning mode of welding and derived welding in the process of adding triangle wave scanning, not only the forming good welded joints can be attained, but also the welding joints hardness values and tensile strength are improved. The average tensile strength of the welded joint is 178.8 MPa, the maximum tensile strength can reach 85% of the base metal, and the elongation rate is 84.5%, which is the weakest in the weld fusion zone compared with the whole weld zone.
This is a preview of subscription content, log in via an institution to check access.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Huang XH, Tu JP, Zhang CQ et al (2007) Spherical NiO-C composite for anode material of lithium-ion batteries. Electrochim Acta 52(12):4177–4181
Poizot P, Laruelle S, Grugeon S et al (2002) Rationalization of the low-potential reactivity of 3d-metal-based inorganic compounds towards Li. J Electrochem Soc 149(9):A1212–A1217
Poizot P, Laruelle S, Grugeon S et al (2000) Nano-sized transition-metal oxides as negative-electrode materials for lithium-ion batteries. Nature 407:496–499
Neudecker BJ, Zuhr RA, Bates JB (1999) Lithium silicon-tin oxynitride (LiySiTON): high-performance anode in thin-film lithium-ion batteries for microelectronics. J Power Sources 81–82:27–32
He DQ, Wu HG (2010) The friction stir welding of copper with a large thickness. J Univ Sci Technol Beijing 10(32):1302–1305
Irisarri AM, Barreda JL, Azpiroz X (2010) Influence of the filler metal on the properties of Ti-6Al-4V electron beam weldments: part I: welding procedures and microstructural characterization. Vacuum 84:393–399
Zhang M, Chen G, Zhou Y et al (2014) Optimization of deep penetration laser welding of thick stainless steel with a 10 kW fiber laser. Mater Des 53(1):568–576
Sokolov M, Salminen A, Katayama S et al (2015) Reduced pressure laser welding of thick section structural steel. J Mater Process Technol 219:278–285
Li S, Chen G, Zhou C (2015) Effects of welding parameters on weld geometry during high-power laser welding of the thick plate. Int J Adv Manuf Technol 79(1):177–182
Powell J, Ilar T, Frostevarg J et al (2015) Weld root instabilities in fiber laser welding. J Laser Appl 27(S2)
Bachmann M, Avilov V, Gumenyuk A et al (2014) Experimental and numerical investigation of an electromagnetic weld pool support system for high power laser beam welding of austenitic stainless steel. J Mater Process Technol 214(3):578–591
Wu Y, Cai Y, Wang H et al (2015) Investigation on microstructure and properties of the dissimilar joint between SA553 and SUS304 made by laser welding with filler wire. Mater Des 87:567–578
Zhang BG, Wu L, Feng JC (2004) Research status of electron beam welding technology at home and abroad. Welding 2:5
Hu HQ, Feng CS (2007) Metal solidification principle. Machinery Industry Press, Beijing
Nakagawa H, Katoh M, Matsuda F (1970) Effects of welding heat and travel speed on the impact property and microstructure of FC welds. Trans JWS 1:94–98
Huang XY (2008) Electron microscopy analysis of material microstructure. Metallurgical Industry Press, Beijing
Xing L, Hang CP, Ke LM et al (2002) Microstructure and electrical properties test of friction stir welded joint of copper. Proc Eleventh Nat Weld Conf 1:456
Callister DW Jr (2000) Materials science, and engineering, an introduction. Wiley, New York
Lu L, Shen YF, Chen XH et al (2004) Ultrahigh strength and high electrical conductivity in copper. Science 422–426
Xue P, Xiao BL, Zhang Q et al (2011) Achieving friction stir welded pure copper joints with the nearly equal strength to the parent metal via additional rapid cooling. Scripta Mater 64(11):1051–1054
Zhao XJ (2016) Study on fiber laser welding T2 copper plate and joint performance. Liaoning University of Technology
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2019 Springer Nature Singapore Pte Ltd.
About this paper
Cite this paper
Zhang, Z., Wang, S., Xin, J., Chen, Y., Huang, Y. (2019). Effect of Scanning Mode on Microstructure and Physical Property of Copper Joint Fabricated by Electron Beam Welding. In: Chen, S., Zhang, Y., Feng, Z. (eds) Transactions on Intelligent Welding Manufacturing. Transactions on Intelligent Welding Manufacturing. Springer, Singapore. https://doi.org/10.1007/978-981-13-7418-0_8
Download citation
DOI: https://doi.org/10.1007/978-981-13-7418-0_8
Published:
Publisher Name: Springer, Singapore
Print ISBN: 978-981-13-7417-3
Online ISBN: 978-981-13-7418-0
eBook Packages: Intelligent Technologies and RoboticsIntelligent Technologies and Robotics (R0)