Advertisement

Effects of Cooling Rate and Grain Refiner on Semi-solid Rheocasting Slurries of Al–Zn–Mg Alloy

  • Min Luo
  • Daquan Li
  • Wenying Qu
  • Xiaokang Liang
  • Jianzhong Fan
Conference paper
Part of the Lecture Notes in Mechanical Engineering book series (LNME)

Abstract

Swirled Equilibrium Enthalpy Device (SEED) process was used to make Al–4.8Zn–1Mg semi-solid slurries. The effects, about cooling rate and Al–5Ti–1B on semi-solid slurry microstructure and temperature field, were studied in detail. It was found that slow cooling rate was helpful to decrease slurry temperature gradient. The temperature difference between slurry centre and edge decreased from 8.3 to 4.1 °C when the cooling rate decreased from 1.63 to 0.69 °C/min. But low cooling rate also resulted in coarser grain. Grain morphology and size was modified by grain refiner. Trace amount of Al–5Ti–1B changed the grain morphology and size greatly, and improved the homogeneity of slurry microstructure. When the content of Ti increased from 0, 0.01 to 0.12%, the grain size was decreased from about 800 to 115 and 75 μm respectively. These results suggested that low cooling rate and grain refiner were necessary for making Al–4.8Zn–1Mg semisolid slurry.

Keywords

Semi-solid rheocasting Al–Zn–Mg alloy Cooling rate Al–5Ti–1B Microstructure 

Notes

Acknowledgements

Financial support from the National Key Research and Development Program of China (N0.2016YFB0303001) and Shenzhen Free Exploring Basic Research Project (JCYJ20170307110223452) is gratefully acknowledged.

References

  1. 1.
    B. Dang, X. Zhang, Y.Z. Chen et al., Breaking through the strength-ductility trade-off dilemma in an Al-Si-based casting alloy. Sci. Prog. 6, 30874 (2016)Google Scholar
  2. 2.
    S. Janudom, J. Wannasin, P. Kapranos et al., The effect of hot tearing in semi solid casting of aluminum A201 alloy. Adv. Mater. Res. 739, 190–195 (2013)CrossRefGoogle Scholar
  3. 3.
    J. Wannasin, D. Schwam, J. Yurko et al., Hot tearing susceptibility and fluidity of semi-solid gravity cast Al-Cu alloy. Solid State Phenom. 116, 76–79 (2006)CrossRefGoogle Scholar
  4. 4.
    H.B. Dong, J.D. Hunt, A. Novel, Single-pan scanning calorimeter. Measurement of thermophysical properties of metallic alloys. J. Therm. Anal. Calorim. 64, 341–350 (2001)CrossRefGoogle Scholar
  5. 5.
    D. Spencer, R. Mehrabian, M. Flemings, Rheological behavior of Sn-15 pct Pb in the crystallization range. Metall. Trans. 3, 1925–1932 (1972)CrossRefGoogle Scholar
  6. 6.
    U.A. Curle, H. Möller, G. Govender, R-HPDC in South Africa. Solid State Phenom. 192, 3–15 (2013)Google Scholar
  7. 7.
    M.C. Flemings, Behavior of metal alloys in the semisolid state. Metall. Trans. B 22, 269–293 (1991)CrossRefGoogle Scholar
  8. 8.
    A. Bolouri, Q.F. Zhao, P. Côté et al., Microstructure and rheological properties of semi-solid 7075 slurries using SEED rheocasting process. Solid State Phenom. 256, 288–293 (2016)CrossRefGoogle Scholar
  9. 9.
    B. Hallstedt, E. Balitchev, H. Shimahara et al., Semi-solid processing of alloys: principles, thermodynamic selection criteria, applicability. ISIJ Int. 46, 1852–1857 (2006)CrossRefGoogle Scholar
  10. 10.
    D. Liu, H.V. Atkinson, H. Jones, Thermodynamic prediction of thixoformability in alloys based on the Al–Si–Cu and Al–Si–Cu–Mg systems. Acta Mater. 53, 3807–3819 (2005)CrossRefGoogle Scholar
  11. 11.
    B. Murty, S. Kori, M. Chakraborty, Grain refinement of aluminium and its alloys by heterogeneous nucleation and alloying. Int. Mater. Rev. 47, 3–29 (2002)CrossRefGoogle Scholar
  12. 12.
    M.E.L. Pascal Côté, X. Grant Chen, New Developments with the SEED technology. Solid State Phenom. 192–193, 373–378 (2012)CrossRefGoogle Scholar
  13. 13.
    ASTM E112-10, Standard test methods for determining average grain size. ASTM Int. (2010). (West Conshohocken, PA) www.astm.org

Copyright information

© Springer Nature Singapore Pte Ltd. 2018

Authors and Affiliations

  • Min Luo
    • 1
  • Daquan Li
    • 1
  • Wenying Qu
    • 1
  • Xiaokang Liang
    • 1
  • Jianzhong Fan
    • 1
  1. 1.General Research Institute for Nonferrous MetalsBeijingChina

Personalised recommendations