Comparison of the High Cycle Fatigue Behavior of Ti–6Al–4V Produced Respectively by EBM and Hot-Rolling

  • Yunxi Liu
  • Wei Chen
  • Zhiqiang Li
  • Zheyuan Chen
  • Gang Yao
Conference paper
Part of the Lecture Notes in Mechanical Engineering book series (LNME)

Abstract

In this study, the microstructure, texture, and mechanical properties of Ti–6Al–4V(Ti-64) alloy produced by electron beam melting (EBM) and rolling were comparatively researched. The results showed that the microstructure of EBM Ti-64 consisted of columnar β grains growing epitaxially along the build direction. The c axis of α grains was oriented along the build direction, and the intensity was about 27 times random. The plate Ti-64 consisted of about 60 vol% of αp and 40 vol% of βT. The c-axis of α grains were parallel to the transverse direction of the plate and the texture strength was 5 times random. The tensile strength of EBM Ti–6Al–4V material was lower than that of the plate, but the ductility was higher. The EBM material exhibited a much larger variation of strength and ductility. This is because of the finer microstructure in the EBM material and also the microtextured regions in the plate material. The cracks in the plate material all initiated from the surface area but cracks in the EBM material occurred both on sample surface and in interior. The smaller lamellar thickness in the EBM material reduces the dislocation slip length, thus improves the life during the crack initiation stage.

Keywords

Ti–6Al–4V Additive manufacturing High cycle fatigue (HCF) Texture 

References

  1. 1.
    C. Leyens, M. Peters, Titanium and Titanium Alloys (WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim, 2003)CrossRefGoogle Scholar
  2. 2.
    G. Lütjering, J.C. Williams, Titanium (Springer, Berlin, 2007)Google Scholar
  3. 3.
    Z. Lian, Review of titanium industry progress in America, Japan and China. Rare Metal Mat. Eng. 32, 577–584 (2003)Google Scholar
  4. 4.
    R.R. Boyer, An overview on the use of titanium in the aerospace industry. Mater. Sci. Eng., A 213, 103–114 (1996)CrossRefGoogle Scholar
  5. 5.
    Y. Yang, Y. Luo, H. Zhao et al., Current status of research and application of titanium alloys for ships in China. Rare Metal Mat. Eng. S 2, 538–544 (2011)Google Scholar
  6. 6.
    Y. Li, Y.Y. Li, T.T. Dong, Influence of stress ratio and residual stress on fracture modes of Ti-64 under high cycle fatigue. Chin. J. Mech. Eng. 51, 45–50 (2015)CrossRefGoogle Scholar
  7. 7.
    I. Gibson, D.W. Rosen, B. Stucker, Additive Manufacturing Technology: Rapid Prototyping to Direct Digital Manufacturing (Springer Science and Business Media LLC, New York, 2010)CrossRefGoogle Scholar
  8. 8.
    C.K. Chuna, K.F. Leong, C.S. Lim, Rapid Prototyping: Principles and Applications, 2nd edn. (World Scientific, Singapore, 2003)Google Scholar
  9. 9.
    H. Tang, J. Wang, S. Lu et al., Progress in melt-forming technology of electron beam selection. Mat. Chin. 34, 225–235 (2015)Google Scholar
  10. 10.
    L.E. Murr, E. Martinez, K.N. Amato et al., Fabrication of metal and alloy components by additive manufacturing: examples of 3D materials science. J. Mater. Res. Technol. 1, 42–54 (2012)CrossRefGoogle Scholar
  11. 11.
    W.E. Frazier, Metal additive manufacturing: a review. J. Mater. Eng. Perform. 23, 1917–1928 (2014)CrossRefGoogle Scholar
  12. 12.
    W. Zhou, Z. Zhao, W. Chen, Analysis of influencing factors of high cycle fatigue properties of titanium alloy. Mod. Mach. 3, 90–93 (2009)Google Scholar
  13. 13.
    J. Schijve, Fatigue of Structures and Materials (Kluwer Academic, Dordrecht, 2001)Google Scholar
  14. 14.
    M.R. Bache, W.J. Evans, H.M. Davies, Electron back scattered diffraction (EBSD) analysis of quasi-cleavage and hydrogen induced fractures under cyclic and dwell loading in titanium alloys. J. Mater. Sci. 32, 3435–3442 (1997)CrossRefGoogle Scholar
  15. 15.
    F. Bridier, P. Villechaise, J. Mendez, Slip and fatigue crack formation processes in an α/β titanium alloy in relation to crystallographic texture on different scales. Acta Mater. 56, 3951–3962 (2008)CrossRefGoogle Scholar
  16. 16.
    S.K. Jha, C.J. Szczepanski, R. John et al., Deformation heterogeneities and their role in life-limiting fatigue failures in a two-phase titanium alloy. Acta Mater. 82, 378–395 (2015)CrossRefGoogle Scholar
  17. 17.
    S.K. Jha, C.J. Szczepanski, P.J. Golden et al., Characterization of fatigue crack-initiation facets in relation to lifetime variability in Ti–6Al–4V. Int. J. Fatigue 42, 48–257 (2012)CrossRefGoogle Scholar
  18. 18.
    A.L. Pilchak, J.C. Williams, Observations of facet formation in near-α, titanium and comments on the role of hydrogen. Metall. Mater. Trans. A 42, 1000–1027 (2011)CrossRefGoogle Scholar
  19. 19.
    Li Xingwu, Xia Shaoyu, Sha Aiyue, Fatigue properties of Ti-64 alloy. Acta Metall. Sin. 38, 277–279 (2002)Google Scholar
  20. 20.
    A.C. Collop, Deformation and fracture mechanics of engineering materials (4th edition). Eng. Struct. 19, 283–283 (1997)CrossRefGoogle Scholar

Copyright information

© Springer Nature Singapore Pte Ltd. 2018

Authors and Affiliations

  • Yunxi Liu
    • 1
    • 2
  • Wei Chen
    • 1
    • 3
  • Zhiqiang Li
    • 1
    • 2
  • Zheyuan Chen
    • 1
    • 3
  • Gang Yao
    • 1
  1. 1.AVIC Manufacturing Technology InstituteBeijingChina
  2. 2.Aviation Key Laboratory of Science and Technology on Plastic FormingBeijingChina
  3. 3.Power Beam Processing LaboratoryBeijingChina

Personalised recommendations